Question about 2010 Nissan Murano

Open Question

How do i remove steering column on 2010 nissan murano?

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: '06 Nissan Murano factory radio/cd player removal steps

what holds the radio in place besides the 2 side screws in a 2006 nissan murano

Posted on Feb 08, 2009

Dak408
  • 277 Answers

SOURCE: How do you remove the

dak408_166.gif

dak408_167.gif

Removal and installation
REMOVAL

CAUTION:

  • The rotation of the spiral cable (SRS air bag component part) is limited. If the steering gear must be removed, set the front wheels in the straight-ahead direction. Do not rotate the steering column while the steering gear is removed.
  • Remove the steering wheel before disconnecting the coupling joint to avoid damaging the spiral cable.
  1. Disconnect battery negative terminal.
  2. If necessary, remove the steering wheel.
  3. Remove the instrument column cover and lower driver instrument panel.
  4. Remove the combination meter.
  5. Remove the cluster lid and center console assembly.
  6. Remove the instrument panel screws from the LH side of the instrument panel to allow the ignition switch to clear the instrument panel during removal.
  7. Remove LH lower knee protector.
  8. Disconnect the following:
    • Telescopic motor, if equipped
    • Telescopic sensor, if equipped
    • Tilt motor, if equipped
    • Tilt sensor, if equipped
    • Headlamp switch
    • Wiper switch
    • Spiral cable
    • Key in reminder
    • Immobilizer
    • Illumination lamp
    • Ignition switch
    • Column harness clips, position aside
  1. Remove the shaft lower cover.
  2. Remove the pinch bolt.
  3. Remove the steering column nuts and steering column. INSTALLATION Installation is in the reverse order of removal. CAUTION: When installing the steering column, finger-tighten all of the lower bracket and joint retaining bolts; then tighten them to specification. Do not apply undue stress to the steering column. NOTE: Align **** of the coupling joint with projection on dust cover. Insert the joint until surface A contacts surface B.
dak408_168.gif
  • After installation, turn steering wheel to make sure it moves smoothly. Ensure the number of turns are the same from the straight-forward position to left and right locks. Be sure that the steering wheel is in a neutral position when driving straight ahead.

Posted on Dec 12, 2010

dttech
  • 4803 Answers

SOURCE: how to remove center console of 2007 nissan murano

There is a lot to explain about how to remove the center console in your vehicle. The instructions from the service manual is copyrighted information and cannot be posted here. Trying to explain it all would be too time consuming as well as very difficult to do. So, Instead of attempting to post all of the information on this page, I have assembled a PDF file for you to download which has step-by-step instructions as well as a few illustrations. You can download the file for free at:

http://depositfiles.com/files/3460au660

Please note that this file will be deleted in about three days and will not be available for download after that.

Posted on May 07, 2012

emissionwiz
  • 75814 Answers

SOURCE: how can i remove lower steering joint on a maxima 2004

It is a very tight fit after the clamping bolt is removed, just keep tapping on it with a hammer or mallet.

Posted on Jun 14, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Set 1 2 switches? please clarify


See pg. 3-31 in owners manual. Start car in park. Adjust seat, telescoping wheel, and side view mirrors. Pust Mem button and then within 5 sec. push either 1 or 2. That button should light to show memory stored.
From the 2012 Guide (See link)
l"AUTOMATIC DRIVE POSITIONER (if so equipped) Two positions for the driver's seat, steering column and outside mirrors can be stored in the automatic drive positioner memory. Follow these procedures to set the memory positions: • Confirm the shift lever is in the P (PARK) position. • Push the ignition switch to the ON position. • Adjust the driver's seat, steering column and outside mirrors to the desired positions using the adjusting switches for each feature. • Push the SET switch and within 5 seconds, push the memory switch (1 or 2) for at least 1 second. • The indicator light on the memory switch you select will illuminate for approximately 5 seconds. • The driver's seat, steering column and outside mirror positions are now set to your preference. These memorized positions can also be linked to your NISSAN Intelligent Key®. For more information, refer to the "Pre-driving checks and adjustments (section 3)" of your Owner's Manual." https://owners.nissanusa.com/content/techpub/ManualsAndGuides/Murano/2012/2012-Murano-quick-reference-guide.pdf
For added info see whole owners manual.

Dec 28, 2015 | 2006 Nissan Murano

1 Answer

Where is the airbag module located on my 2005 nissan murano. is it in the steering column?


There is no module for air bags .
There is a fuse its not something that needs sensors unless their is an impact witch their are sensors for but not a signal module. because its a federial mandate and their several impact points on vehclies.

Mar 07, 2015 | 2005 Nissan Murano SL

3 Answers

What is the reason that my 2010 nissan murano steering becomes so hard at low speed and when is startibng to move


Your vehicle has an electric power steering system. More than likely you have a weak battery or faulty electric motor.

Dec 18, 2014 | 2010 Nissan Murano

1 Answer

HORN IS ONLY BLOW WHEN I TURN THE STEERING WHEEL


Bad spiral cable in column behind steering wheel.

Feb 22, 2014 | 2007 Nissan Murano S

1 Answer

Nissan murano steering wheel stiff


We had the same problem with our 2007 Murano. However, the steering assembly (Box) actually broke and flipped upside down. This caused the car to turn sharp to the right and hit the cub while turning. Nissan said we caused the damage when we hit the cub and refused to pay for the damages. Look into the steering assembly before you also have an accident. Our insurance went up $20 a month.

Sep 07, 2012 | 2007 Nissan Murano SE

1 Answer

Had a 2007 Murano with backup camera that worked great. Now with the 2010 Murano the video is so dark is is nearly worthless. How can I increase the brightness?


There is abrightness control on right hand side of touch screen controls. I think it has a picture of a part moon and a star (sun). Try that.
A new Murano owner.

Oct 23, 2010 | 2010 Nissan Murano

1 Answer

I have a 2009 Murano LE loaded; the tilt steering column makes a grinding noise like it wants to move in the pre-set position but all it does is stay at the lowest setting. What could be the problem? ...


The problem has to do with the internal gears, or at least that's what it sounds like to me. My steering column on my 09 murano had the exact same symptoms so I took it to the dealership and they had to replace the internal gears in the steerining column, luckily it was still covered under warranty otherwise who know how much it wouldve cost.Good Luck!
-Zeke

Sep 02, 2010 | 2009 Nissan Murano

1 Answer

OBD port location


i always thought it was to the right of the column, just below the dash

May 11, 2010 | 2006 Nissan Murano

1 Answer

Whininhg from power steering pump


That is the power steering belt routed around pump pulley that is slipping . The power steering is located behind the steering column, replacing and re-routing the belt is not an easy repair.

If instead the whining noise comes from under the hood , that is the serpentine belt, that is easier to repair.

May 02, 2009 | 2005 Nissan Murano

Not finding what you are looking for?
2010 Nissan Murano Logo

Related Topics:

330 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...