Question about 1995 Chevrolet G20

Open Question

Need diagram for 1995 g20 van heater hose to heater control valve

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Shouldibuyit
  • 44 Answers

SOURCE: replace heater core 1994 chevy g20 conversion van

Here a are the instuctions to remove it. I did not know if you have A/C or not so I included both for you.

REMOVAL & INSTALLATION
Without Air Conditioning
ALL MODELS
See Figure 1

  1. Disconnect the negative battery cable.
  2. Remove the coolant recovery bottle.
  3. Place a pan under the van and disconnect the heater intake and outlet hoses. Quickly remove and plug the hoses and support them in an upright position. Drain the coolant from the heater core into the pan.
CAUTION When draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
  1. Remove the heater distributor duct-to-case attaching screws and the duct-to-engine cover screw. Remove the duct.
  2. Remove the engine cover.
  3. Remove all the instrument panel attaching screws.
  4. Carefully lower the steering column. Raise and support the right side of the instrument panel. Refer to for further details.
  5. Remove the defroster duct-to-case attaching screws and the two screws attaching the distributor to the heater case.
  6. Disconnect the temperature door cable. Carefully fold the cable back and out of the way.
  7. Remove the three nuts from the engine compartment side of the distributor case and the screw from the passenger compartment side.
  8. Remove the heater case and core assembly.
  9. Remove the core retaining straps and remove the core.
To install:
  1. Install the core.
  2. Install the core retaining straps.
  3. Install the heater case and core assembly.
  4. Fasten the three nuts on the engine compartment side of the distributor case and the screw on the passenger compartment side.
  5. Connect the temperature door cable.
  6. Install the defroster duct-to-case attaching screws and the two screws attaching the distributor to the heater case.
  7. Install the steering column.
  8. Fasten all the instrument panel attaching screws.
  9. Install the engine cover.
  10. Install the duct. Install the heater distributor duct-to-case attaching screws and the duct-to-engine cover screw.
  11. Connect the heater intake and outlet hoses.
  12. Fill the cooling system.
  13. Install the coolant recovery bottle.
  14. Connect the negative battery cable.
1990-95 MODELS With A/C

  1. Disconnect the battery ground cable.
  2. Remove the engine cover.
  3. Remove the steering column-to-instrument panel bolts. Lower the column carefully.
  4. Remove the upper and lower instrument panel attaching screws. Remove the radio support bracket screw.
  5. Raise and support the right side of the instrument panel.
  6. Remove the lower right instrument panel bracket.
  7. Remove the vacuum actuator from the kick panel.
  8. Disconnect the temperature cable and vacuum hoses at the case. Remove the heater distributor duct from over the engine hump.
  9. Remove the two defroster duct-to-firewall attaching screws below the windshield.
  10. Under the hood, disconnect and plug the heater hoses at the firewall.
  11. Remove the three nuts and one screw (inside) holding the heater case to the firewall.
  12. Remove the case from the van. Remove the gasket for access to the screws holding the case together. Remove the temperature cable support bracket. Remove the screws and separate the case. Remove the heater core.
To install:
  1. Install the heater core.
  2. Assemble the case and fasten the screws.
  3. Install the temperature cable support bracket.
  4. Position the gasket, then install the case in the van.
  5. Fasten the three nuts and one screw (inside) holding the heater case to the firewall.
  6. Connect and plug the heater hoses at the firewall.
  7. Fasten the two defroster duct-to-firewall attaching screws below the windshield.
  8. Install the heater distributor duct.
  9. Connect the temperature cable and vacuum hoses at the case.
  10. Install the vacuum actuator at the kick panel.
  11. Install the lower right instrument panel bracket.
  12. Fasten the radio support bracket screw.
  13. Fasten the upper and lower instrument panel attaching screws.
  14. Fasten the steering column-to-instrument panel bolts.
  15. Install the engine cover.
  16. Connect the battery ground cable.
  17. Refill the cooling system as necessary.

Posted on Nov 28, 2008

Ad
  • 1 Answer

SOURCE: Electronic Control Module Installation 1994 G20 Chevy Van

I just had the same problem. If it is a regular van try under the driver seat in a plastic box. If it is a conversion van try in a pannel just behind driver seat on side of van wall behind a pannel that looks like a vent.

Posted on Apr 09, 2009

Danno5691
  • 17 Answers

SOURCE: How do you set the timing on a 350 chevy engine in

If the distributor hasn't been taken out, the timing can be set manually but you have to disconnect the distributor wire behind the glove box inside the cab. Tan wire with white tracer it is taped up to the a multi wire harness but is the only one with a single plug. Disconect the plug and use your timing light on the timing mark to set timing per specs. Rotate the distributor as needed to advance or retartd as required for the correct setting. tighten the dizzy clamp and plug the tan wire back together. The computer will now be fooled asd to what the base timing is and advance from there.
Contrary to popular belief, 96' and up do not have this wire. Timing has to be done with a programmable scanner.
Dan
Hope this helps.

Posted on Apr 25, 2009

  • 13 Answers

SOURCE: belt change for 1995 chevy g20

there should be a diagram sticker under the hood . first thing check to make shure all accesories move freely no locked pullys that may have shot the belt to begin with

Posted on Jul 18, 2009

johnjohn2
  • 5763 Answers

SOURCE: routing diagram for a Chevy G20 serpentine belt?

Okay, there are a few engines that come in this van, lucky there the same except,they come with or without ac or airpump, so i will give you all of them and you choose the right one.a613984.gif492790a.giffd1ae03.gif47b4a5f.gif

Posted on Mar 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heat or air not blowing out of any vents in my 95 Chevy g20 van


the heater control valve might be broken or plugged

Dec 11, 2016 | 1995 Chevrolet G20

1 Answer

Trans. modulator on a 93 g20 van ?


Depends on the type of transmission in the van. Most late model transmissions use electronic shift solenoids to control shift points. If the transmission in this van has a modulator valve, it is located on the passenger side of the van near the middle of the transmission with a vacuum hose attached to it.

Feb 25, 2015 | Cars & Trucks

1 Answer

Need fuse box diagram for chevy g20 van


look at fuse box behind drivers seat, as well as under dash in front of drivers seat,,all top lights,and mood lights behind drivers seat, small door on side of van apx 2 feet back of drivers seat

Nov 20, 2012 | 1995 Chevrolet G20

2 Answers

My 1992 chevy g20 van surges and i'm not sure exactly why. I changed the pcv valve, fuel filter, spark plugs, and air filter. What are some possibilities


My first thought would be a vacuum leak in one of the hoses. Rubber hoses get brittle with age and even a small crack in a hose may cause surging. Happened to me in a Lumina.

Apr 26, 2012 | 1997 Chevrolet Astro

1 Answer

I need a stereo wiring diagram for 1995 chevrolet g20 gulf stream van


Below is a wiring diagram. I do not have a picture of the connector but there are wire colors on the diagram which should help you figure it out. Also I believe if there was no cassette deck in the vehicle (factory), I don't believe there were any rear speakers. Hope this helps....

3_11_2012_9_07_49_pm.jpg

Mar 11, 2012 | 1995 Chevrolet G20

1 Answer

95 chevy van g20 starts runs rough and when you step on gas it stalls


I recommend checking the EGR valve first as GM cars and trucks of this era are famous for small ckunks of carbon getting lodged in the valve seat and holding the valve open causing rough idle and general undriveability.

Apr 10, 2011 | 1995 Chevrolet G20

2 Answers

Where is the jack stored on our 1995 Chevy G20 van


It should be located on the right hand side fender wall on most Chevrolet / GMC Vans. Another location it may be under your hood on one of the fender walls (these is more common with Dodge)

Aug 23, 2009 | 1995 Chevrolet G20

1 Answer

700R4 transmission diagrams needed


Im needing and exploded view of the inside of a 700 R 4 transmission

Jul 31, 2009 | 1992 Chevrolet G20

1 Answer

Belt change for 1995 chevy g20


there should be a diagram sticker under the hood . first thing check to make shure all accesories move freely no locked pullys that may have shot the belt to begin with

Apr 04, 2009 | 1993 Chevrolet G20

1 Answer

My 1995 ford areostar van when heat is on only blows cold air


The aerostar has a vacuum operated watervalve in the heater tubing.the valve is located on the
passenger side inner fender behind the aircleaner.with someone operating the controls inside the van
you can check to see if you get vaccum by removing the tiny hose that goes to the water valve
and checking for suction as you in the van person operates the heater conthttp://www.fixya.com/PostAnswer.aspx?thid=1323651&prdid=696348rols. If you have no
vaccum there is a break in the hose between the intake manifold and the valve. If you do get
vaccum check to see if the valve changes position from vaccum on to vaccum off. you can see
this motion on the small lever on the side of the valve. If the valve lever doesn't move you can
move it manually to allow the water to flow through the heater core. if the valve won't move manually
there is an obstruction in the valve. If it does move manually the vaccum diaphragm is gone.
replace the valve. if it moves to the manual open position you can hold it open with a tywrap.
before you get to this point you should first check to see that there is enough coolant in the
radiator. If you still have no heat you can check the coolant flow through the heater core. to do
this remove both heater hoses from the valve and pump water from a hose into one of the hoses
water should flow from the other hose. If it doesn't the heater core is blocked. The rear heater
operates the same way with the watervalve under the van just behind the drivers seat.
Good luck.

Dec 02, 2008 | 1995 Ford Aerostar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

450 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...