Question about Cars & Trucks

Open Question

2007 DODGE NITRO ESP/BAS LIGHTS ON WHAT THE PROBLEM

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
tunde007
  • 2382 Answers

SOURCE: ESP/BAS warning light on. went

Hi, these systems are all linked together. Most commonly, one of the wheel speed sensors is not reading or is reading incorrectly. This can also occur on slippery surfaces where one or more wheel slides enough to cause the sensor to drop the signal, but not enough to meet criteria for an abs or esp episode. If the light comes back every time you turn on the ignition, there is a deeper problem.
The system has detected a fault in the electronic stability program - brake assist system. You have an electrical connection at the rear wheels secured to the inside of the brake area and are viewable from under the vehicle. It is a small wire harness running to each wheel. Grab the connector and wiggle it around, and make sure they are tight. Due to the connector being mounted low to the ground, sometimes they become dirty or corroded, not making contact. Do this on both sides and see if the lights turn off.

If the light does not turn off, you have to replace dynamics sensor, which is mounted UNDERNEATH the center console in the car. There is a "lost communication to dynamics sensor" and "low voltage to dynamics sensor supply"..

Posted on Feb 13, 2011

Ad
Benimur
  • 6966 Answers

SOURCE: Warning Light on Mercedes ML270

Hi,

To my understanding:
BAS ESP - Electronic Stability Program (keeps you moving in the direction you intended the vehicle to go); probably a faulty brake switch or a bad brake sensor. You may want to reference this forum for additional insights;
ETS - Electronic Traction System (keeps you moving); would require an appropriate code reader to diagnose and pinpoint problem.Surprisingly, there has been some reports of defective brake pedal switch that activates this warning. You may lilkewise want to reference this forum for additional insights.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Posted on Jun 06, 2008

mercanic
  • 14 Answers

SOURCE: mercedes benz bas/esp light on

Change the brake light switch first, its on the brake pedal, £9 from mercedes.
jib
www.mercanic.co.uk

Posted on Nov 24, 2008

bschilz
  • 2049 Answers

SOURCE: where is the oil filter on a 2007 dodge nitro v6

You can access the oil filter easily from underneath next to the front, driver-side wheel at the front of the engine. There is clear access to the filter there.

For more info on Dodge Nitro, visit the forum at
http://www.dodge-nitro.com/dodge-nitro/

Posted on Aug 08, 2009

  • 3 Answers

SOURCE: Where is the fuse for rear brake lights on 2007

In the fuse box, under the hood on the drivers side. There is a detailed map of what fuses do what on the inside of the box cover.

Posted on Sep 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The esp bas light is on my 2009 dodge 1500 and it won't start


An Electronic Stability Program (ESP)/Brake Assist System (BAS) indicator is standard equipment on all instrument clusters. The ESP/BAS indicator is serviced as a unit with the instrument cluster.
The ESP/BAS indicator gives an indication to the vehicle operator when the Electronic Stability Program (ESP)/Brake Assist System (BAS) has been activated. This indicator is controlled by a transistor on the instrument cluster circuit board based upon cluster programming and electronic messages received by the cluster from the Controller Antilock Brake (CAB) and the Transmission Control Module (TCM) over the Controller Area Network (CAN) data bus.
The ESP/BAS indicator Light Emitting Diode (LED) is completely controlled by the instrument cluster logic circuit, and that logic will only allow this indicator to operate when the instrument cluster receives a battery current input on the fused ignition switch output (run-start) circuit. Therefore, the LED will always be OFF when the ignition switch is in any position except ON or START. The LED only illuminates when it is provided a path to ground by the instrument cluster transistor. The instrument cluster will turn ON the ESP/BAS indicator for the following reasons:
  1. Bulb Test- Each time the ignition switch is turned to the ON position the ESP/BAS indicator is illuminated for about four seconds as a bulb test.
  2. ESP/BAS Indicator Lamp-On Message- Each time the cluster receives an electronic ESP/BAS indicator lamp-ON message from the CAB indicating that the ESP/BAS system has been activated, the ESP/BAS indicator will be illuminated. The indicator remains illuminated until the cluster receives a lamp-OFF message from the CAB, or until the ignition switch is turned to the OFF position, whichever occurs first.
  3. ESP Full Off Textual Message- Each time the cluster receives an electronic ESP Full OFF indicator lamp-ON message from the CAB indicating that the ESP/BAS system has been manually disabled, an ESP OFF textual message will appear within the cluster odometer display. The ESP OFF textual message remains displayed until the cluster receives a lamp-OFF message from the CAB, or until the ignition switch is turned to the OFF position, whichever occurs first.
  4. Actuator Test- Each time the cluster is put through the actuator test, the ESP/BAS indicator will be turned ON, then OFF again during the bulb check portion of the test to confirm the functionality of the LED and the cluster control circuitry.
The CAB continually monitors the ESP/BAS circuits and sensors to decide whether the system is in good operating condition and the proper outputs to the components of the system. The CAB then sends the proper lamp-ON or lamp-OFF message to the Electro Mechanical Instrument Cluster (EMIC) (also known as the Cab Compartment Node/CCN).
For proper diagnosis of the ESP/BAS system, the CAB, the TCM, the EMIC, the CAN data bus or the electronic communication related to the ESP/BAS indicator operation a diagnostic scan tool is required. Refer to the appropriate diagnostic information.

Apr 11, 2016 | Dodge Cars & Trucks

1 Answer

2007 dodge magnum in limp mode now esp/bas has come on and oil light even though ots fill of oil how do i fix this??


Have the codes read. This helps point you in a direction to look. The eps/bas came on because of limp mode. The oil light? could be a bad sensor.

Apr 09, 2016 | Dodge Cars & Trucks

3 Answers

2007 dodge durangos brake light came on then the brake pedal got really hard to press so i replaced the whole braking system and it was good for 2 days now the brake is hard esp bas brake lights on


If your truck has a brake booster, I suspect the vacuum hose to the booster has gotten fuel into it or just gotten old and is collapsing inside.

Apr 27, 2015 | 2007 Dodge Durango

1 Answer

Our Dodge Nitro was parked for about 5 weeks and when we started it up the ABS, ESP, lights came on, also a picture of a car with squiggly lines under the wheels. Any suggestions?


Make sure the battery didn't expire

2007 original battery ? & not charging it while parked!

Once the computer monitors run, that issue may go away
IF the battery is good & module voltage is good,if not
then you will have to have the problem diagnosed

Maybe you have an abs problem & the rest is just a coincidence

I would run my scan tool software & look at the modules in enhanced data & road test until all monitors run clean,in your
situation

Unfortunately folks don't own professional tools at home
& have decades of vehicle knowledge for a hobby, just me
I guess

Jul 16, 2014 | 2007 Dodge Nitro SXT

1 Answer

2008 dodge charger ESP/BAS and traction light on


Have the brakes inspected for worn out brake pads causing a metal to metal scrape of the pad and brake rotor.

Mar 20, 2014 | Dodge Charger Cars & Trucks

2 Answers

2007 Chrysler 300 Touring ESP light on


un hook your battery to reset the computer , if it persits you may have to change the esp sensor keep in mind once you disconnect the battery it will clear your error codes and it can not be read later.

Mar 19, 2013 | 2007 Chrysler 300 Touring

2 Answers

I have an 06 Dodge Magnum. ESP/BAS light


Whenever this warning or any other stays on in the dash it id indicating that the systems control module has detected a fault, it then disables the system as long as the light is on. You must now have the dealer hook up a special electronic diagnostic tool and "scan" the system for the fault code that is stored for the problem(s)

Sep 19, 2012 | 2006 Dodge Magnum

1 Answer

2007 JEEP LIBERTY ESP BAS ABS WARNING LIGHTS


i took my 2007 jeep liberty 4x4 to the carwash but it was freezing out side as soon as i came out of the carwash the esp abs the skid car in the middle came on

Apr 09, 2012 | 2007 Jeep Liberty Sport

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

3,615 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...