Question about 2008 Dodge Avenger

Open Question

2008 dodge avenger blower motor resistor location

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: locating heater blower motor resistor

the resistor is behind your glove box. open the box and push in the sides to release it and let it hang down...the resistor is right there. I didn't try to replace it, a friend did it, but the part was under $20.

Posted on Feb 01, 2009

SOURCE: 1999 Dodge Ram 1500 Fan Motor Resistor Location

I've never seen a vehicle w/o a blower resistor. You don't need to remove the blower. The resistor is about 2 inches x 3 inches and is installed in a hole in the plenum (duct) near the blower motor. It will have a wiring harness connected to it. It could be under the passenger dash or under the hood, depending on where the blower motor is.

Posted on May 06, 2009

hardinfarms
  • 144 Answers

SOURCE: blower motor resistor location on 1998 dodge

It's on the right rear engine compartment.5a8f741.jpeg

Posted on Oct 02, 2009

  • 63 Answers

SOURCE: 2008 Dodge Avenger check engine light

Not sure if this will work for you but worth a shot. I own a 2005 dodge neon. I know the ecu's are different but maybe dodge was smart and made all the cars this way. Insert you key into ignition. Turn key forward until you are at the last position right before the car starts to crank over. Repeat this for a total of three times then on your digital odometer display, you will see a set of numbers displayed. this will be your code for the malfanction(s) that set your check engine light. Like I said, it might not work on your car but give it a shot. If not, rent an obdII scanner and get your codes. Then you know where to start looking to fix your problem.

Posted on Dec 17, 2009

  • 1 Answer

SOURCE: 2008 dodge avenger spark plug location and socket size.

  • 2008+ Dodge Avenger 2.4L 4cyl.
  • Remove plastic cover on top of engine, just pull on each corner for it is friction fit.
  • Once removed you will see 4 black spark plug covers with one hex type screw holding each.
  • Remove Hex screw and place aside, pull upward to remove plug boot from plug.
  • To remove the plug, use a 5/8 socket with a 6" extension. Once plug has been turned out all the way and you cannot get the plug up and out of the hole, just press the plug boot back on the plug and pull it back up.
  • Gap and replace 4 plugs with the same or equavalent type,. Drop plug down the hole and use socket to align and tighten until just snug, then torque to manufactures specifications.

Posted on Feb 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the heater resistor on a 2005 dodge dakota? Behind glove box?


should be just above the blower motor. You will need to remove the glove box door to gain access.

Dec 12, 2015 | 2005 Dodge Dakota Club

1 Answer

My 2010 Dodge Avenger the blower was only working on the to low and medium prop mob up with penny work for a while to penny fell out won't work now


2009 dodge avenger blower motor works on low, medium ...

www.fixya.com/.../t21143783-2009_dodge_avenger_blower_motor_wo...
Nov 2, 2013 - 2009 dodge avenger blower motor works on low, medium low,medium high but not high. Resister has ... SOURCE: Dodge 2001 Stratus - A/C fanonly blows on High ... working. Jan 04, 2010 ' 2003 Dodge Durango ยท 1 Answer ...

Oct 29, 2015 | Dodge Cars & Trucks

1 Answer

I need to find the exact location of the starter motor relay for a 2008 dodge avenger


Starter Activation Is Controlled By Totally Integrated Power Module--Left Side Of Engine Compartment.
Can Be Checked With Scanner (buss lines) Has Solinoid On Starter

Feb 18, 2015 | 2008 Dodge Avenger

1 Answer

Where is the blower motor resistorlocation on 2008 dodge avenger


on the fuse pannels or somewhere along the wiring harnes itself

Oct 26, 2013 | 2008 Dodge Avenger

1 Answer

High speed blower


Usually the high speed circuit bypasses the resistor. There should be a relay for high. I did not see it in the fuse box in the engine compartment, but it may be listed in your owners manual.
If there is a relay you should be able to test it to see if the high circuit is getting power.

Aug 30, 2012 | 2008 Dodge Avenger

1 Answer

No high speed blower on heating or air


check for bad connection on wiring, turn blower on high and wiggle wiring under dash around blower motor and resistor area

Aug 30, 2012 | 2008 Dodge Avenger

1 Answer

I need know which relay is for the ac/heat blower.


It is located under the hood in the fuse and relay center. Consult your owners manual for detailed info. If you don't have an owners manual you can get one here from Dodge free.
http://www.dodge.com/en/owners/manuals/

Jun 27, 2012 | 2010 Dodge Avenger

1 Answer

2008 Dodge Avenger fuel filter location


my father is fixing my 2008 dodge avenger,he cannot find where the fuel pump relay is located on my car

Feb 23, 2012 | 2008 Dodge Avenger

1 Answer

Where is the blower motor resistor located on a 1988 dodge lancer


REMOVE GLOVE BOX ASSEMBLY LOWER RIGHT SIDE INSTRUMENT PANEL TRIM COVER AND RIGHT COWL TRIM PANEL. WHEN YOU WILL SEE BLOWER WIRES THATS WHERE YOUR RESISTOR LOCATED. DISCONNECT BLOWER MOTOR WIRES THEN REMOVE RESISTOR.

Dec 06, 2010 | 1988 Dodge Lancer

1 Answer

I have a 2006 Dodge Ram diesel. Can you tell me where the resistor for the blower motor is located ?


It's right next to the blower, above the passenger's feet. See pic below.


jturcotte_37.jpg
  1. Disconnect and isolate the negative battery cable.
  2. Reach under the instrument panel near the blower motor and disconnect the wire harness connector from the blower motor resistor.
  3. Remove the two screws that secure the blower motor resistor to the HVAC housing.
  4. Remove the blower motor resistor from the HVAC housing.

Nov 30, 2010 | 2006 Dodge Ram 2500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

897 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...