Question about Dodge Cars & Trucks

Open Question

07 cummins keeps blowing pcm fuse - Dodge Cars & Trucks

Posted by on

  • josh Nov 08, 2012

    actully quit blowing the fuse but the pcm is not acting like its getting power

×

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: the 20amp fuse for the PCM keeps blowing when

replace the pcm

Posted on Sep 28, 2009

Ad
  • 14036 Answers

SOURCE: 2003 trailblazer keeps blowing pcm

YOU HAVE MANY THINGS THAT CAN BLOW THE PCM FUSE.STARTER RELAY,ALTERNATOR, PARK NEUTRAL SAFETY SWITCH, FUEL PUMP, AND THE PCM CAN BE SHORTING OUT.

Posted on May 02, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hummer 2 2003 pcm fuse keeps blowing


Check your starter signal wire is not shorted to ground. Make sure its not rubbing on the chassis.

Feb 07, 2016 | Hummer H2 Cars & Trucks

1 Answer

2008 X. Why does PCM fuse #23 keep blowing?


Sounds like the is a wire shorting to earth

Dec 23, 2015 | Ford Taurus Cars & Trucks

1 Answer

Why does my pcm fuse keep blowing on my ford f150


Check the Powerbox for a group of Relays and try replacing the PCM Relay.

Mar 15, 2014 | 2004 Ford F150

1 Answer

97 ford f-150 PCM power fuse keeps blowing,


that could be a tricky situation because you don't know if it's the pcm itself or a circuit that it controls. first you must know whether or not it is a short in the power or ground supplies to the pcm, then if that is all ok, you have to disconnect all sensors, injectors, etc, everything that it controls and see if it blows a fuse. if it doesn't, then you have to hook them back up one by one and see which one will blow the fuse.

Mar 08, 2013 | Cars & Trucks

1 Answer

2002 PT Ignition start fuse blowing


PCM?? No they are wrong I think, keep looking at every wire fuse 30 supplies power to, you will need buy the factory wiring diagrams.

Oct 24, 2012 | 2006 Chrysler PT Cruiser

1 Answer

2003 trailblazer keeps blowing pcm fuse. wont start, key stuck in on position.


YOU HAVE MANY THINGS THAT CAN BLOW THE PCM FUSE.STARTER RELAY,ALTERNATOR, PARK NEUTRAL SAFETY SWITCH, FUEL PUMP, AND THE PCM CAN BE SHORTING OUT.

May 01, 2011 | 2004 Chevrolet TrailBlazer

2 Answers

02 dodgeram 2500 4x4 manual tran with 24valve 5.9 cummins lift pump went bad than after replacing truck ran rough intermittinally + ck eng lite comes on, so replaced vp inj pump n lost 1 code still 4...


high voltage is an indication something is not plugged in or plugged in wrong. You will need to test the harness to see if the required voltage supply is present, connector unplugged, if not then your going to have to determine if the siganl comes from the PCM or the fuse block. If its the PCM you may have a bad PCM. Same thing for the ground side. Now if the reference signal and ground are good you could have a sensor issue but I doubt this because you have high voltage on three components. This tells me that three component signals are not getting back to the PCM. This is why it sets the codes. With all the work you just did I suspect you didnt but the wiring back the way it was. Sometimes people take the ground wire off between the engine and and body because its in the way and don't reinstall it. Or don't tighten it enough. With todays electronics there simple mistakes cause unforeseen issues.

Nov 24, 2009 | Dodge Pickup Cars & Trucks

2 Answers

Number six cylinder misfire on an 07 dodge 6.7 cummins


you may have an injector stuck open or not firing at all..a dodge or cummins tech should look at

Apr 07, 2009 | 2007 Dodge Ram Truck

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...