Question about 1998 Toyota Camry

Open Question

Where is Blower Motor Resistor for 1998 Toyota vienta grande

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 373 Answers

SOURCE: Where is blower motor resistor

HI....
The BLOWER motor resistor on a Toyota Camry 01.
Is located Behind center right side of dash.
ON blower housing.
If you vehicle is equipaded with protection cover.
Just you need to remove the cover. and will see the blower resistor.

I hope this information work for you.

Thank you for use fixya.

Posted on Jul 21, 2008

  • 154 Answers

SOURCE: Blower motor has only low speed

You may need to get the correct resistor, as they are designed to only allow so much amperage to go through them. If it is getting very hot it is runnig to many amps through it. It will eventually blow and you will need to replace it anyway.

Posted on Jul 28, 2008

  • 1861 Answers

SOURCE: 1999 toyota vienta drivers side rear electric window not working

You need to replace the window regulator assembly.
The cables that run the glass up and down have broken inside the regulator.

Hope this helps. A FixYa rating would be greatly apprecited.

Posted on Jan 21, 2009

  • 318 Answers

SOURCE: I have a 1999 Toyota

It could either be the speed control switch or the resister pack near the blower.

Posted on Jun 23, 2009

  • 1986 Answers

SOURCE: how do i program a remote control for a 1998

1-insert and remove key from ignition two times

2-close and open driver door two times

3-insert and remove key once from ign.

4-close and open drvr door twice

5-insert key into ign.,then close driver door

6-turn key to on (not start) then off, twice this is rewrite mode,have all remotes to reprogram it will clear any lost remotes.

7-remove key from ignition,the door locks should cycle twice.if not start over.it may take a few tries.

8-press lock/unlock together and hold for a second

9-release,and press lock on remote,the door locks will cycle confirming program.continue to do other remotes you have,steps 8 and 9.if only one in possession,you are done. To end mode open door or insert key into ignition.

You'll need to follow the steps with no more than a 1-2 second delay between each step.. hope it works

Posted on Aug 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove heater blower motor?


1998 ATC Jeep Grand Cherokee Blower Resistor connector ...

? 0:55
www.youtube.com/watch?v=sDFLuenx9aw
Nov 14, 2012 - Uploaded by Freedomautomotive1
1998 ATC Jeep Grand Cherokee Blower Resistor connector Repair Kit (RARE 1/2 Year) ... How to Fix a Chrysler Blower FanThat Only Works on High - Duration: 16:51. ... JEEP2001 FIXING THE HEATER BLOWER CONTROL. ... Jeep Grand CherokeeCenter and Lower Dash Removal - Auto Repair Series ...

Sep 30, 2015 | 1998 Jeep Grand Cherokee

1 Answer

1998 dodge grand caravan blower motor resistor


please go to this site for more info. http://www.ehow.com/how_7669595_remove-caravan-blower-motor-resistor.html this is for a 1998 dodge caravan. hope this helps ! good-day !

Feb 22, 2012 | Dodge Grand Caravan Cars & Trucks

1 Answer

Trying to find blower motor resister on a 98 grand am pontiac i need to replace it but dont know where to start can some one be detailed


REMOVE LOWER RIGHT DASH INSULATOR PANEL FROM BELOW THE GLOVE BOX.YOU HAVE TO SLIDE BCM MODULE ASIDE THE BLOWER MOTOR RESISTOR ON THE BLOWER MOTOR HOUSING WHERE ELECTRICAL CONNECT TO BLOWER MOTOR. TO KEEP FROM SETTING OFF THE THEFT SECURITY SYSTEM, WHEN YOU MOVE THE BCM MODULE. ASIDE FIRST TURN OFF RADIO,THEN DISCONNECT NEGATIVE BATTERY CABLE.THEN REPLACE BLOWER MOTOR RESISTOR.

Jul 31, 2011 | 1998 Pontiac Grand Am

1 Answer

For a1998 i need to know where is the relay for a grand am blower motor resistor stop blowing


RELAY SHOULD BE ON TOP OF AIR PLENUM BEHIND GLOVE BOX (MOST GM)
THE RESISTOR IS LOCATED UP STEEM FROM BLOWER MOTOR (BOTTOM PASSENGER SIDE) CHECK FOR POWER AT BLOWER MOTRO CONECTION FIRST AND FUSE ALSO
VERY RARE TO LOOSE ALL SPEED AT ONCE UNLESS FUSE OR BLOWER MOTOR OR
SWITCH

Apr 17, 2011 | 1998 Pontiac Grand Am

1 Answer

Blower motor on 2000 toyota camry works only on hi settig


Hi!!
The blower motor speeds are ultimately controlled by the Blower Motor Resistor, when the Resistor becomes defective, current goes right thru it and the Blower Motor only operates at max. speed. Replacing the Resistor is a simple task. Locate electrical connector to blower motor, trace back wiring no more than 8" to next plug, The device where the plug is connected to is the Blower Motor Resistor, disconnect plug and remove the two screws, remove and replace Resistor.
Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.

Mar 15, 2011 | 1998 Toyota Camry

2 Answers

Blower motor resistor location


should be right next to the blower motor, heavy gauge wire running to it

Oct 22, 2010 | 1998 Jeep Grand Cherokee

1 Answer

Trying to locate blower motor resistor in 1998 Jeep Grand Cheroke


blower resistor is right next to motor under passenger side of dash.

Jun 20, 2009 | 1998 Jeep Grand Cherokee

1 Answer

Blower reisitor, 1998 Toyota Tacoma


The blower motor resistor is located in the heater box area, which is under the dashboard on the passenger side. You will find the resistor in the large squarish tube that leads to the center of the dash from the blower motor housing (right to left on an american vehicle). Unplug the large black wiring connector, remove the 2 phillips screws and the resistor is ready to pull out of the heater box.

Sep 19, 2008 | 1998 Toyota Tacoma

Not finding what you are looking for?
1998 Toyota Camry Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...