Question about 2005 Nissan Altima

Open Question

P1611 XDI C21 RESTRON CAR CAN STAR - 2005 Nissan Altima

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Mini Cooper codes 1611 1613


That would be P1611 and P1613, the letter is important as it indicates the system of the car affected, in this case the powertrain. I would unplug the large connector to the transmission and see if water has intruded into it. if so blow it out until it is dry and reinstall it. If that doesn't fix the problem you need to get a transmission repair shop involved in the diagnosis and repair.

Oct 07, 2016 | 2006 Mini Cooper

1 Answer

Rexton 270 xdi


change all the fuel filters and bleed any air out of the system. Check the variable action of the turbo actuator and check that the vacuum hose to it is not brittle and cracked.. Run fault codes to see if any faults have been recorded

Mar 03, 2014 | Cars & Trucks

1 Answer

Code p1610 & p1611


Dont know where you found these fault codes but their not in my nissan list or the universal codes ,no my main suspect is the alternator diodes now charge the battery and then disconnect the alternator wires and see what happens when car is left for a few days

Jan 29, 2014 | Nissan Micra Cars & Trucks

1 Answer

Hi could you tell me please is a freelander 2000 xdi buying to pull a caravan


Look up the gross weight of the Caravan and then the towing capacities listed for the truck.

Oct 30, 2012 | 2002 Land Rover Freelander

1 Answer

Byundai trouble code p1611


Hi there:
DTC P1611 - MIL request signal circuit low input

This code is for a short to ground in MIL (Malfunction Indicator Light) system. Possible causes are short to ground between the ECM (Engine Control Module) and the TCM (Transmission Control Module), faulty ECM or faulty TCM.

A Hyundai scanner is required to test the ECM and TCM.
A short to ground means that wire is shorting out to ground(exposed wire touching metal). faulty means that the ECM or TCM is not working properly.
Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 29, 2012 | Hyundai Cars & Trucks

1 Answer

Hi i got an error code of p1611 thank u


P1611 =
MIL request signal circuit low input MIL-on Request Line

This code is set when the MIL On Request from the TCM (Transmission Control Module) has/had a problem getting the information to the ECU (Engine Control Module). In the 98 Elantra, there are two separate computer modules; one for the engine, the other for the transmission. (both located under the dash Driver's side. The diagnostic procedure specifies the wiring between the ECM & TCM be checked for any damage/defects. If none found, then replace the TCM with a new one to see if the problem (code) occurs again. If communication between TCM & ECM is corrected, you should have a ****** code related to the MIL On Request from the TCM (****** codes begin with P07 w/the next two digits (??) identifying the specific transmission component/malfunction).

You can also Go to www.hmaservice.com and register your vehicle by VIN #.. you'll then have access to wiring diagrams, shop & owner manuals, service bulletins, campaigns, illustrations and procedures, etc

Sep 14, 2011 | 1998 Hyundai Elantra

Not finding what you are looking for?
2005 Nissan Altima Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14251 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...