Question about 2006 Pontiac G6

Open Question

Timing belt replacement pontiac g6 06

My check engine light is on and the auto zone diagnostic said it could be a cam shaft sensor or the timing belt. How much would a timing belt replacement cost approximately. trying to brace myself.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: 1999 pontiac grand prix . will not run

If wiggling the wires cured the code, then one of the wires is broken inside the insulation. Pull on each wire one at a time. look for the colored insulation to stretch, this will be the broken wire. For the other car that wont rev up, this is a common when the catalytic concverter is plugged up. This will also cause MAF codes, and in turn, TRAC OFF light.
See http://www.greatautohelp.com

Posted on Oct 17, 2008

  • 1 Answer

SOURCE: Pressure Control Solenoid "D" Electrical

You need to take it to a reputable repair facility. The pressure control solenoid needs to be checked for proper operation. If the solenoid is operating properly, the PCM (Powertrain Control Module[computer]) will need to be replaced. If you continue to drive the vehicle with this condition the transmission will eventually destroy itself.

Posted on Apr 03, 2009

csmock132
  • 4669 Answers

SOURCE: Replace timing belt on 99 Pontiac Grand Am 2.4 L

This engine is chain drive. You shouldn't need to replace it unless it has a problem. Do you have a problem with it?

Posted on Jun 08, 2009

snafu86
  • 193 Answers

SOURCE: 2005 pontiac Grand Prix, check engine light on, Catalytic convert

Tuneup time is around 90,000 to 100,000 miles.If it were to ignition coil you would feel the misfire. Plugs, wires, airfilter and fuel filter should be changed before cat is. Plugs will tell the story.

Posted on Jul 21, 2009

  • 844 Answers

SOURCE: I have a 2006 Pontiac

when you changed the parts did you have the codes cleared ? as if the comp stored it then it will return and when you put new parts on it took the comp time to test and display new changes.

Posted on Jan 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When replacing the cam position sensor I see Oil in the cam position sensor port


get an OFFICIAL diagnosis from someone with a much more sophisticated reader. It doesn't have to be the dealer... just a good mech that specializes in GM

Mar 25, 2014 | 2007 Pontiac G6

1 Answer

What else could be the problem?


did you reset the light after change of sensers as some require reset to come out of limp mode

Dec 26, 2013 | 2004 Nissan Quest

1 Answer

2004 chrysler sebring 2.4l dohc.


Have you ever replaced the timing belt?? If not the problem is likely to be a loose worn out timing belt. A floppy belt will play havoc with the sensor signals and trigger a check engine light and a camshaft sensor code.

Jun 22, 2012 | 2002 Chrysler Sebring

1 Answer

2008 Kia Rio-After I replaced the timing belt my check engine light came on. I was told that the cam shaft position sensor was bad and needed to be replaced. I replaced it and the check engine light came...


were the codes cleared after replacment if not try that
if they were test the wires for cam signal and check for damaged ---cuts---fraied---pinched

May 28, 2011 | 2008 Kia Rio

1 Answer

HI MY CAM BELT STRIPPED AND JUST WANTED TO CHECK OUT THE CORRECT TIMMING MARK ON THE CAM SHAFTS PLEASE


If the timing belt stripped out chances are a valve in the interference engine was bent. These engine are called interference engines because they are designed in such a way that if the belt breaks or strips out the valve gets in the way of the piston and get hit by the piston, the timing marks can be found in a haynes repair manual found at Auto Zone or Advanced Auto Zone.

Dec 07, 2009 | 2000 Daewoo Nubira

1 Answer

Rpm guage cuts out and car quits but starts right away all the time


Best thing to do is go to Auto Zone and have the care scanned for any DTC codes. Auto Zone scan free of charge and that way we might get to the problem right away. It could be your cam sensor or crank shaft sensor or both that may have gone bad. There are just to many sensors that can shut down the engine and getting the car scanned will eliminate replacing good parts. Good luck and keep me posted.

Jul 12, 2009 | 1997 Pontiac Grand Prix

2 Answers

Check engine light blinks


Ok, i would ave the ignition coil pack tested for its operational valve asap if possible. this is either an ignition coil pack issue or, a bad ECM. the ECM controls the ignition timing in this vehicle so, the problem will be there if the crank shaft sensor and cam sensors are ok.

I would pull the trouble codes asap as well. this will help diagnosis this issue correctly. this can be done at a local auto zone or a local mechanics shop as well.

Jun 19, 2009 | 2001 Ford Windstar

1 Answer

Lod chirping, squeling noise from engine in ford taurus. Belt is


The cam shaft stabilizer for the 2003 to 2005 have been a known issue. They will intermitantly squel till they go completly out.

I took my 2003 and 2005 Turas to a professional mechanic. They where able to verify the cam shaft stabilizer was the issue since the squeling noise was coming from top right side of the engine.

The surpintine (fan, AC) belts are locted on the left side of the engine.

Once I had the cam shaft stabilizer replaced. I never had that squel again.

Mar 28, 2009 | 2005 Ford Taurus

Not finding what you are looking for?
2006 Pontiac G6 Logo

Related Topics:

480 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...