Question about 2005 GMC Sierra 1500

Open Question

P2761 - Torque Converter Clutch Pressure Control Solenoid Control Circuit/Open

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: 1997 transmission Slow Acceleration

not sure if this is the answer yet but i have the same problem with the same codes i work at an auto parts store and a few of the techs that are customers have lead me in the direction of changing the ignition switch, i am doing it today will let you know if it solves the problem

Posted on Jan 27, 2010

ZJLimited
  • 17970 Answers

SOURCE: 06 odyssey po741

Hi there:
This code is related to the TCC circuit in the transmission. It is either stuck in the closed position (regulator valve, or control valve) or it has a bad torque converter. You will need to take it to a reputable transmission shop to have some fluid line pressure tests done. The cost of course will depend on the repair needed. Some parts of the repair for this are pretty simple and only require removal of the oil pan and valve body to access related parts, but if the converter has ballooned and needs to be replaced the transmission will need to come out for repairs. Most good shops are happy to give you a free written estimate, ask for one before you authorize any repair work. Could be rather simple, but could just as easily be complex, hard to tell from where I'm setting. Better to have it tested than to just start throwing expensive parts at it in an attempt to fix it. Most of these failures are caused by dirt, and things getting plugged up due to lack of maintenance.

Honda Service News November 2003 TITLE:
A/T DTC P0740, P0741 Repair Tips: Another Look APPLIES TO:
All Models

SERVICE TIP:
If you're doing a repair for DTC P0740 or P0741 (lock-up control system) on any Honda models with A/T, except Passport, refer to this table first:

2_21_2012_3_22_47_pm.gif


If there is no S/B posted on ISIS for the vehicle you're working on, go to the DTC P0740 or P0741 troubleshooting procedure in the Automatic Transmission section of the appropriate S/M or under DTC Troubleshooting in ISIS. If the procedure recommends replacing the A/T, make sure you have a reman A/T on hand. Remove the original A/T, and look at the condition of the torque converter O-ring. Then follow these tips to ensure a lasting repair.

Missing or cut O-ring . If the O-ring is missing or cut, the ATF can leak internally, causing DTC P0740 or P0741 to set. Replace the O-ring, and reuse the original A/T. Make sure the problem has been fixed by connecting the HDS and testdriving the vehicle using the previous DTC P0740 or P0741 freeze data parameters (match the TPS and VSS values for at least 25 seconds ). If the DTC comes back, install the reman A/T. If the DTC doesn't come back, return the reman A/T to the reman center.

Flattened or deformed O-ring . If the O-ring is flattened or deformed, replace the A/T. The O-ring can get damaged if the ATF pump seizes up and overheats. Make sure the problem has been fixed by connecting the HDS and testdriving the vehicle using the previous DTC P0740 or P0741 freeze data parameters (match the TPS and VSS values for at least 25 seconds ).

O-ring is OK . If the O-ring is round and in good condition, the most likely cause for DTC P0740 or P0741 to set is the A/T, the torque converter, or both. Install the reman A/T. Make sure the problem has been fixed by connecting the HDS and test-driving the vehicle using the previous DTC P0740 or P0741 freeze data parameters (match the TPS and VSS values for 25 seconds ). Before you install the reman A/T, make sure the O-ring on the torque converter is properly installed.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Posted on Feb 21, 2012

emissionwiz
  • 75197 Answers

SOURCE: gmc p0741 torque converter clutch circuit performance or stuck off

The transmission oil pan must be removed and the TC solenoid tested, if it works you will need to remove the transmission replace the Torque Converter.

Posted on Jun 07, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

.2005 Silverado 6,0 codes po307,po332,po455,po2761 changed plugs and wires. need help .suggestions pleaSe


P0307: Cylinder 7 Misfire Detected
http://www.autocodes.com/p0307_chevrolet.html

P0332: Knock Sensor 2 Circuit
http://www.autocodes.com/p0332_chevrolet.html

P0455: Evaporative Emission Control System Leak Detected Gross Leak
http://www.autocodes.com/p0455_chevrolet.html

P2761: Torque Converter Clutch Pressure Control Solenoid Valve Circuit
http://www.autocodes.com/p2761_chevrolet.html

Oct 28, 2016 | 2005 Chevrolet Silverado

1 Answer

I have a 2001 aurora and code p1860 p1860 came up what is this and how much to fix


P1860 All GM - TCC (transmission Torque Converter Clutch) PWM Solenoid Circuit Electrical.
P1860 Description The Torque Converter Clutch Pulse Width Modulation (TCC PWM) solenoid valve controls the fluid acting on the converter clutch valve. The converter clutch valve controls the TCC application and release. The solenoid attaches to the control valve body within the transmission. The solenoid receives ignition voltage through circuit 239. The Powertrain Control Module (PCM) controls the solenoid by providing a ground path on circuit 418. Current flows through the solenoid coil according to the duty cycle (percentage of ON and OFF time). The TCC PWM solenoid valve provides a smooth engagement of the torque converter clutch by operating during a duty cycle percent of ON time.
When is the code detected? When the PCM detects a continuous open, short to ground or short to power in the TCC PWM solenoid valve circuit, then DTC P1860 sets. DTC P1860 is a type B DTC.

Possible causes - Faulty Torque Converter Clutch Pulse Width Modulation (TCC PWM) Solenoid
- Torque Converter Clutch Pulse Width Modulation (TCC PWM) Solenoid harness is open or shorted
- Torque Converter Clutch Pulse Width Modulation (TCC PWM) Solenoid circuit poor electrical connection. Unless you have a factory manual and very good auto repair skills this is best left to an expert. It is a messy dirty job that requires removing the parts inside the transmission for testing..

Aug 23, 2016 | Cars & Trucks

1 Answer

P0740 honda odyssey


P0740 Honda - Transmission Lock-Up Control System Fault Possible causes
- Low transmission fluid level
- Dirty transmission fluid
- Faulty torque converter clutch solenoid valve
- Torque converter clutch solenoid valve harness is open or shorted
- Torque converter clutch solenoid valve circuit poor electrical connection

Tech notes
On some Honda vehicles the P0740 code may be set by an overheating torque converter problem which is caused by an insufficient flow to the torque converter release circuit.

P0740 Honda Description
The torque converter clutch solenoid valve is activated, with the gear in D4, by the Transmission Control Module (TCM) in response to signals sent from the vehicle speed and the Engine Control Module (ECM). Lock-up piston operation will then be controlled. When the torque converter clutch solenoid valve is activated, the torque converter lockup clutch will engage creating a 1 to 1 RPM ratio between the transmission input shaft and the rotational speed of the torque converter.
Lock-up operation, however, is prohibited when A/T fluid temperature is too low.
When the accelerator pedal is depressed (less than 2/8) in lock-up condition, the engine speed should not change abruptly. If there is a big jump in engine speed, there is no lock-up.

Dec 04, 2013 | 2000 Honda Accord

1 Answer

Multiple DTC's Solenoid, Torque Converter related... I ran an ODB II read & these are the codes it returned: P0740 - Torque Converter Clutch Solenoid Circuit P0753 - Shift Solenoid A...


For starters I would run a fault code check to find out what item was affected . Next if nothing was amiss I would run the fault code reader to reset the CPU and see what parts of the CPU program was now working.

Nov 01, 2013 | 2004 Chevrolet Silverado

1 Answer

From a stop engine is running fine (not over speeding) but vehicle starts slowly as if on wrong gear


code p0740 refers to torque converter clutch (TCC) solenoid --circuit malfunction Causes---Wiring---TCC solenoid--- ECM/TCM
Code p2716 refers to transmission fluid pressure(TFP) solenoid D-electrical Causes---Wiring---TFP solenoid.
Code p0785 refers to shift/ timing solenoid circuit malfunction Causes---Wiring---shift/timing solenoid---ECM?TCM The common fault here appears to be the TCM ( transmission control module) have it check out..

Apr 07, 2013 | 2005 GMC Sierra

1 Answer

Codes po740, po743 ? po753 all at once. Where should i begin for repairs?


You must do the diagnostics for each code.
Here are the possibilitesP0740 DODGE - Torque Converter Clutch Circuitxicon.jpghttp://engine-codes.com/p0740_dodge.htmlForum CodePossible causes- Low transmission fluid level
- Dirty transmission fluid
- Faulty torque converter clutch solenoid valve
- Torque converter clutch solenoid valve harness or connectors
- Torque converter clutch solenoid valve circuit is open or shorted
P0743 DODGE - Torque Converter Clutch Solenoid Circuitxicon.jpghttp://engine-codes.com/p0743_dodge.htmlForum CodePossible causes- Faulty torque converter clutch solenoid valve
- Torque converter clutch solenoid valve harness or connectors
- Torque converter clutch solenoid valve circuit is open or shorted
- Low transmission fluid level
- Dirty transmission fluid

P0753 DODGEP0753 DODGE - 3-4 Shift Solenoid Relayxicon.jpghttp://engine-codes.com/p0753_dodge.htmlForum CodePossible causes- Faulty shift solenoid valve
- Shift solenoid valve harness or connectors
- Shift solenoid valve circuit is open or shorted
- Low transmission fluid level
- Dirty transmission fluid

Jul 03, 2012 | 1997 Dodge Ram 1500 Club Cab

1 Answer

How to fix p2761code


P2761 - Torque Converter Clutch Pressure Control Solenoid Control Circuit/Open

Feb 23, 2012 | 2005 GMC Sierra 1500

1 Answer

1998saab 900s po743


P0743: Torque Converter Circuit Electrical

- Faulty torque converter clutch solenoid valve
- Torque converter clutch solenoid valve harness or connectors
- Torque converter clutch solenoid valve circuit is open or shorted
- Low transmission fluid level
- Dirty transmission fluid

Feb 06, 2012 | 1996 Saab 900

1 Answer

Check engine light on, code P2761, 2005 GMC 2500 VAN


P2761=Torque Converter Clutch Pressure Control Solenoid Control Circuit/Open

Dec 18, 2009 | 2005 GMC Sierra 2500HD 4WD

Not finding what you are looking for?
2005 GMC Sierra 1500 Logo

Related Topics:

297 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...