Question about 2000 Mazda 626

Open Question

Does a 2000 mazda 626 have an inertia switch

Turns over but wont start getting power to coil and fuel pump

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: I have 1987 Mazda B2200 2.2 ltre, turns, fires, no fuel psi.

I had something like this before. There is a fuel saftey switch near the gas tank right by the rear end. Its a roll over sensor and mine fell off the mount and I guess the truck thought it was upside down :)

Posted on Jan 01, 2009

rcampsr
  • 90 Answers

SOURCE: Do you know where or if a 2000 Mazda 626 has a

Hello, I am going to make a few assumptions here. The vehicle has an electric fuel pump and you replaced it. The vehicle has fuel injection. The engine is actually cranking, just not starting, when you say "car still won't crank". You are getting fire to the spark plugs at the plug ends. You checked the fuel pump for power at the pump. No power, then you back traced the wire to the fuse block and checked the fuse to see if it was blown. If the fuse is good back trace the power to the ignition switch and/or ECM for power. You have power at the pump, check the ground and make sure it is connected properly. Will the pump run when someone turns the key on? Pump runs, check fuel manifold for pressure. No pressure, check the fuel filter for blockage, or replace it. Fuel pump doesn't run, new replacement pump is defective. There is usually some type of control module for the fuel pump on fuel injected vehicles. Good Luck, RAC

Posted on Apr 18, 2009

wracefans24
  • 1985 Answers

SOURCE: How to Replace a Fuel pump on a 2000 Mazda 626

yes it isn't that much if you buy them.they slide inside the coupler and release the line.

Posted on Dec 27, 2009

Testimonial: "Thank you didn't know if there was a tool for this."

wracefans24
  • 1985 Answers

SOURCE: 2000 mazda 626 wont start,is turning over,fuel

if you have spark at the plugs you need to check fuel pressure at reed valve on fuel rail,you will need at least 55psi to fire injectors,

Posted on Dec 27, 2009

  • 2 Answers

SOURCE: 1999 mazda 626 wont start

truns over strong and feul pump is on but fire to cam

Posted on Mar 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does the 98 Mazda 626 have a inertia switch and if so where is it located at?


More than likely, my vote goes to the trunk/tailgate area. Some are under the spare tire.

Sep 06, 2016 | 1998 Mazda 626

1 Answer

Is there a fuel inertia cut off switch and where is it located?


Only Ford products use an inertia switch, and it only turns off in a wreck.
Have you checked the fuel pump relay to see if it is sending power to the pump ?

Mar 26, 2016 | 2001 Mazda 626

1 Answer

Where is the inertia switch located on a mazda 626, 2002


Only Ford products use an inertia switch for the fuel pump.
Mazda only uses a relay controlled by the engine computer.

Oct 21, 2015 | Mazda Cars & Trucks

1 Answer

2000 mazda protege 1.6 liter dx..... I have no power to my fuel pump I have replaced the pump and relays and fuses are good... Where is my inertia switch on this vehicle


No inertia switch on the Prot?g?. Ford thing. Not used by Mazda. No voltage to the Red with white stripe wire at fuel pump?

Sep 18, 2015 | Mazda Cars & Trucks

1 Answer

Where is the inertia switch located on a 2000 626 Mazda


You Mazda does not have an inertia switch like the fords do. The only things that control the fuel pump are the pcm, fuel pump relay, and the fuel pump fuse.

May 25, 2015 | 2000 Mazda 626

1 Answer

Need location of tipped inertia switch on 2000 mazda 626


To the best of my memory it doesn't have one the computer shuts the fuel off its probably a relay out or bad pump being that old good chance it is the pump

Jan 03, 2015 | Cars & Trucks

1 Answer

I have no power going to the fuel pump


one thing to check is the inertia switch. it kills power to the fuel pump in case of an accident, or sometimes a large pothole. it can be reset once you locate it.

Aug 31, 2014 | 2000 Mazda 626

1 Answer

Where is inertia switch in 94 Mazda 626 2.0


No inertia switch. That was a common problem on these cars., The alarm box gave problems and it is what is causing the fuel pump to shut off. Good luck finding one. The easiest and cheapest way to fix is to give it ignition power when you turn ignition on. If you want to be a bit safer, buy a ford KA inertia switch, secure it at the l/f kick panel directly onto the body (It works with shock waves) to cut of fuel in case of an accident Luckily you don't have to take the tank out, you just remove the rear seat and the metallic cover. .

Jul 27, 2014 | 1994 Mazda 626

1 Answer

Is there a reset button for a fuel pump 94 Mazda 626


Here you go, it should be to the left of your left foot wile sitting in the driver's seat under a panel.

Jul 23, 2014 | 1994 Mazda 626

1 Answer

Mazda 626 2000 Need to know where the reset or inertia switch is


The is no Fuel Inertia Switch --Only on Ford Products

Jul 12, 2011 | 1995 Mazda 626

Not finding what you are looking for?
2000 Mazda 626 Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...