Question about Cars & Trucks

1 Answer

My toyota 1vd enine 200 series is not switching ignition on have even removed components to another vehicle and they are switching on ignition and startering tje vehicle what could be the problem?

Toyota 1vd engine v8 200 series

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 76,132 Answers

The following are the general instructions on the start of diagnosing any electronically controlled engine or transmission problem.

The engine and the automatic transmission (transmission control is only for automatics, engine is still computer controlled no matter the transmission type) in this vehicle are computer controlled and in most cases when a fault occurs a fault code is stored in the memory of the computer control module. There are exception to this, such as the Mass Airflow Meter and fuel pressure problems. What must be done is to have all the basic testing done such as a scan of the system for fault codes as well as a check with a live data scanner tool for engine functions that are not within range of normal, a trained technician is required to know what is correct and what isn't, then based on careful diagnostics done from a factory repair manual the correct part is replaced or the wiring repaired or the computer replaced (known as the PCM or ECM,ECU), which is very rarely the problem. Other basic checks must be done as well such as mechanical problems with the engine as well as engine state of tune and mileage on the engine. The transmission can have mechanical issues as well such as no gear engagement at all or a failed pump or other pressure related problems. Also engine mechanical problems can and do cause many drive-ability related problem such as rough idle and other symptoms.

Posted on Nov 08, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
virgils
  • 39 Answers

SOURCE: 1999 Toyota Corolla CE.

it sounds like either your having a short at the starter or the ignition switch is bad, I am leaning towards the issue being the starter, usually when the ignition switch is going bad there will be no click,

Posted on Oct 06, 2008

  • 6 Answers

SOURCE: Starter Relay Switch.

your ignition switch are wrong or your starter stay on check with test light at little wire on starter when u are cranking light on when u leave the key no light will come

Posted on Oct 11, 2008

blueextc3221
  • 15935 Answers

SOURCE: 1999 Toyota Solara Starter or Ignition Switch problem?

Your problem is a faulty starter solenoid relay.
It is staying in the POWER ON position.
The relay is located under the hood near the power distribution panel (fusebox) i believe.
Consult your owners manual or Repair manual for exact location.



Thank you for using FixYa - a FixYa rating is appreciated!!

Posted on Jan 30, 2009

  • 2 Answers

SOURCE: Hi, have latest 2010 LC79 Toyota Landcruiser V8

The starter motor is buried in the V8 valley . It is about a days work to replace it . They are very expensive , have only a few service parts and don't like water .

Posted on Aug 02, 2010

jyackle5
  • 8197 Answers

SOURCE: The vehicle is a 1996 Mercury Grand Marquis with a

  1. Disconnect the negative battery cable.
  2. Raise the vehicle and support it safely.

2f393c9.jpg

7d38275.jpg
  1. Label and disconnect the starter cables from the starter. If equipped with starter mounted solenoid, detach the push-on connector from the solenoid.

To detach the hard-shell connector from the solenoid S terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and S terminal.
See Figures 3 and 4

fe5b04c.jpg
3b2189e.jpg

Remove the starter bolts and the starter.


Or you can go to autozone.com to get the info

Good luck and please accept the answer

Posted on Oct 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The landcruiser V8 1VD-Ftv engine can't crank through the button(keyless ignition)but all dashboard lights are on,how do I go about it?


The key have to be less that 12" from the ignition button to defeat the immobiliser.

That vehicle looks derelict!

Dec 23, 2016 | Toyota Land Cruiser Cars & Trucks

1 Answer

How do i remove the ignition cylinder on my 2002 Toyota Rav 4 without the key?


from another post, psoted by James Allmond

How to remove ignition cylinder from Toyota Camry 1993

Here are step-by-step instructions for the removal and re-installation of your ignition cylinder on your Toyota. Hope this sheds some light on the subject and solves your problem. Have a great day!




  1. Disconnect the negative battery cable. If equipped with an air bag, wait at least 90 seconds before working on the vehicle.
CAUTIONSome models covered by this guidemay be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in .
  1. Remove the lower steering column cover. Unfasten the ignition switch connector under the instrument panel.
  2. Remove the screws which secure the upper and lower halves of the steering column cover.
  3. Turn the lock cylinder to the ACC position with the ignition key.
  4. Push the lock cylinder stop in with a small, round object (cotter pin, punch, etc.).
On some vehicles, it may be necessary to remove the steering wheel and combination switch first.
  1. Withdraw the lock cylinder from the lock housing while depressing the stop tab.
  2. To remove the ignition switch, unfasten its securing screws and withdraw the switch from the lock housing.
To install:
  1. Align the locking cam with the hole in the ignition switch and insert the switch into the lock housing.
  2. Secure the switch with its screw(s).
  3. Make sure both the lock cylinder and column lock are in the ACC position. Slide the cylinder into the lock housing until the stop tab engages the hole in the lock.
  4. Install the steering column covers.
  5. Connect the ignition switch wiring.
  6. Connect the negative battery cable.

source

How do remove the ignition cylinder on my 2002 Toyota Rav 4 without the key

Jul 28, 2016 | Toyota Cars & Trucks

1 Answer

WILL TURN OVER BUT WILL NOT START


There are 2 possibilities: the spark plugs are not firing or the fuel system is clogged.

There are 2 ignition switch recalls for your vehicle:

Check your vehicle for the recall service stickers or call BMW and have your VIN number ready when you call and have them run your vehicle service history.

They should be able to tell you if the recall had been performed on your car.

Recall ID # 93253 - ELECTRICAL SYSTEM:IGNITION:SWITCH plus.gif Full Details Recall Date OCT 17, 2012 Component ELECTRICAL SYSTEM:IGNITION:SWITCH Model Affected 7-Series Potential Units Affected Recall ID # 93244 - ELECTRICAL SYSTEM:IGNITION:SWITCH plus.gif Full Details Recall Date OCT 17, 2012 Component ELECTRICAL SYSTEM:IGNITION:SWITCH Model Affected 7-Series Potential Units Affected

Read more: http://www.motortrend.com/cars/2007/bmw/7_series/recalls/#ixzz3Ft0kI54g

Oct 11, 2014 | 2007 BMW 750Li Sedan

1 Answer

How to replace ignaction cylander


Hello, Here are step-by-step instructions for the removal and re-installation of your ignition cylinder on your Toyota.

  1. Disconnect the negative battery cable. If equipped with an air bag, wait at least 90 seconds before working on the vehicle.
CAUTION: Some models covered by this guide may be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in .
  1. Remove the lower steering column cover. Unfasten the ignition switch connector under the instrument panel.
  2. Remove the screws which secure the upper and lower halves of the steering column cover.
  3. Turn the lock cylinder to the ACC position with the ignition key.
  4. Push the lock cylinder stop in with a small, round object (cotter pin, punch, etc.).
On some vehicles, it may be necessary to remove the steering wheel and combination switch first.
  1. Withdraw the lock cylinder from the lock housing while depressing the stop tab.
  2. To remove the ignition switch, unfasten its securing screws and withdraw the switch from the lock housing.
TO INSTALL:
  1. Align the locking cam with the hole in the ignition switch and insert the switch into the lock housing.
  2. Secure the switch with its screw(s).
  3. Make sure both the lock cylinder and column lock are in the ACC position. Slide the cylinder into the lock housing until the stop tab engages the hole in the lock.
  4. Install the steering column covers.
  5. Connect the ignition switch wiring.
  6. Connect the negative battery cable.
Thanks

Aug 12, 2010 | 1989 Toyota Camry

1 Answer

How to Remove an Ignition Cylinder From a Toyota Camry 1994


prev.gif next.gif Ignition Lock/Switch REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable. If equipped with an air bag, wait at least 90 seconds before working on the vehicle. CAUTION
    Some models covered by this manual may be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in Section 6.
  2. Remove the lower steering column cover. Unfasten the ignition switch connector under the instrument panel.
  3. Remove the screws which secure the upper and lower halves of the steering column cover.
  4. Turn the lock cylinder to the ACC position with the ignition key.
  5. Push the lock cylinder stop in with a small, round object (cotter pin, punch, etc.). NOTE: On some vehicles, it may be necessary to remove the steering wheel and combination switch first.
  6. Withdraw the lock cylinder from the lock housing while depressing the stop tab.
  7. To remove the ignition switch, unfasten its securing screws and withdraw the switch from the lock housing. To install:
  8. Align the locking cam with the hole in the ignition switch and insert the switch into the lock housing.
  9. Secure the switch with its screw(s).
  10. Make sure both the lock cylinder and column lock are in the ACC position. Slide the cylinder into the lock housing until the stop tab engages the hole in the lock.
  11. Install the steering column covers and connect the ignition switch wiring.
  12. Connect the negative battery cable.
prev.gif next.gif

Jul 17, 2010 | 1994 Toyota Camry

1 Answer

Toyota starter problrm


NEED TO REPLACE STARTER.

Mar 03, 2009 | 1996 Toyota T100

1 Answer

How to remove ignition cylinder from Toyota Camry 1993


Here are step-by-step instructions for the removal and re-installation of your ignition cylinder on your Toyota. Hope this sheds some light on the subject and solves your problem. Have a great day!




  1. Disconnect the negative battery cable. If equipped with an air bag, wait at least 90 seconds before working on the vehicle.
CAUTIONSome models covered by this guidemay be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in .
  1. Remove the lower steering column cover. Unfasten the ignition switch connector under the instrument panel.
  2. Remove the screws which secure the upper and lower halves of the steering column cover.
  3. Turn the lock cylinder to the ACC position with the ignition key.
  4. Push the lock cylinder stop in with a small, round object (cotter pin, punch, etc.).
On some vehicles, it may be necessary to remove the steering wheel and combination switch first.
  1. Withdraw the lock cylinder from the lock housing while depressing the stop tab.
  2. To remove the ignition switch, unfasten its securing screws and withdraw the switch from the lock housing.
To install:
  1. Align the locking cam with the hole in the ignition switch and insert the switch into the lock housing.
  2. Secure the switch with its screw(s).
  3. Make sure both the lock cylinder and column lock are in the ACC position. Slide the cylinder into the lock housing until the stop tab engages the hole in the lock.
  4. Install the steering column covers.
  5. Connect the ignition switch wiring.
  6. Connect the negative battery cable.

Nov 23, 2008 | 1993 Toyota Camry V6

1 Answer

Programming a 1995 toyota avalon key fob


To program a remote... note that you must not delay more than 10 seconds between any of the operations.

Driver's door open, all other doors closed, key removed from the ignition switch.

Insert key into ignitions switch, then remove it.

Press LOCK then UNLOCK on the vehicle door lock control switch at 1 second intervals 5 times.

close and re-open drivers door.

Press LOCK and UNLOCK on the vehicle door lock control switch at 1 second intervals 5 times

Insert Key into ignition switch.

Switch ignition ON and OFF once to program a remote transmitter code while retaining the original codes or twice to program a remote transmitter code while erasing the original codes. three times to check how many remote transmitters are currently registered, or 5 times to erase all registered codes.

Remove Key from ignition switch.

System should now lock and unlock vehicle. Once, twice or five times depending which mode has been selected. It will lock and unlock one to four times slowly, to indicate the number of remote transmitters registered if you chose option 3.

Press and hold remote transmitter LOCK and UNLOCK buttons at the same time.

Press LOCK remote button for 1 second: System should now lock and unlock vehicle once to confirm, twice to indicate registration has failed.

NOTE: to exit programming mode, close drivers door or insert key in the ignition.

NOTE: a maximum of 4 remote transmitters can be programmed

Oct 13, 2008 | 1995 Toyota Avalon

2 Answers

Car was working fine and then the car would not start. Checked the battery and fully charged. Tried to start again and it started. Turned off car and nothing again. Not even a cranking sound!


Depending of the type of car, and the starting system, you could have up to two starter solenoids on your vehicle. These components sent current to the starter during ignition but your problem sounds like the solenoid or even some of the connections throughout the starting system.(Starter motor, Ground strap, Pos+ cable from battery to solenoid.)

Aug 03, 2008 | 2006 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...