Question about 2005 Ford Ka 1.3

1 Answer

Seems too be where the gear linkage attaches - 2005 Ford Ka 1.3

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 75,797 Answers

Duplicate question.

Posted on Nov 08, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Ford ka engin oil

You really need an inspection pit as the car needs to be level. Unscrew filler cap from front face of gearbox ( carefull though as there is a blanking cap as well and it is the one furthest from engine) The oil level should be between 5mm and 10mm below bottom edge of filler plug)

Posted on Oct 31, 2008

  • 1071 Answers

SOURCE: lower seal ,steering box,92 ford ranger

yes you do but its easy

Posted on Jul 27, 2009

  • 184 Answers

SOURCE: how do i ajust a ford mondeo gear linkage

if memory serves me right you cannot adjust the cables on these cars.

Posted on Sep 25, 2009

  • 5 Answers

SOURCE: Transmission fluid leaking from bell housing when in gear.

If you have never done this before,it may be best to take the truck to a shop or have some one with experience help you. You will need the truck up far enough to take out the transmission. The linkage and drive shaft has to be removed,then unbolt the transmission from the bell housing.Special tools may be needed to pull and replace the seal.
Transmission fluid needs to be changed since it is a brownish color.

Posted on Feb 16, 2010

  • 166 Answers

SOURCE: change master cyl clutch ford ka

Not oil, brake fluid, nasty stuff that removes all paint (Dot 3 and below)... Are you asking for directions or what? your post is cryptic

Posted on Mar 30, 2010

Testimonial: "quick reply"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

94 Toyota 4runner with shifter in park it seems like in gear but will not move


Remove trans pan and check your manual valve it may be broken, or linkage problem, if no problem found then you will need to take a pressure reading but that may be out of your capabilities, have a shop check your trans and give you a diagnostic.

Mar 08, 2016 | Toyota Cars & Trucks

1 Answer

Gear lever is not activating but the clutch is fine


problem with linkage cables. get under vehicle and select a gear
manually with engine off, then climb inside, start up with clutch
pedal depressed, release clutch, if nothing happens, problem in gearbox, if it takes off, problem with linkage cables.

Apr 03, 2014 | Toyota Quantum Cars & Trucks

1 Answer

Mitsubishi shift linkage


Hi Jordan,go check your clutch fluid,if low or out then your clutch slave cylinder is bad,what is your year.I can check it out and send you a repair guide,k.

Feb 05, 2014 | Cars & Trucks

2 Answers

Audi a3 auto reverse gear doesn't move


run fault codes and look for faulty TCM and reverse servo .

Nov 29, 2013 | Audi Cars & Trucks

1 Answer

The gear shifter feels like its not in place


linkage needs ajust--getta haynes manual atta parts store

Aug 25, 2012 | 1990 Ford Escort

2 Answers

Cannot get 5th and reverse gear. Feels like neutral. 1, 2, 3 and 4 work fine.


the linkage is loose or poping out! check to c if trans is tightend down

Aug 22, 2012 | 1995 Dodge Neon

1 Answer

I have a grinding noise in my transmission when I change gears what could this be


Possible wear and tear on the gear linkages/ the shaft/ the gears or the failure to notch.
All this relates to a possible fault within the gear box , check for PLAY of the gear levers/linkages, if worn out change them so that the links MOVE perfectly when the lever is moved to change the gears. Also check the gear box OIL within , if the oil seems to contain metal particles then you need to open the gear box without delay.

Jul 12, 2011 | 1995 GMC Sonoma

1 Answer

Have recently replaced the Clutch Kit on a Peugeot 206 model is 2005. The car is running but goes into third gear instead of first gear at times. It seems as if the linkages are not pushing far enough. Can...


Check to see that none of the gear linkages have been bent or misaligned. Check for wear in the gear linkage joints and also in the gear lever attachment point.

Jan 17, 2011 | 2005 Peugeot 405

1 Answer

Put new tranny in truck the linkage seems to be


Hold the brake pedal down,and try and start the engine in neutral,and drive,and between the gears.You can adjust the gear linkage under the truck ,on the transmission.

Dec 15, 2009 | 1988 Ford Ranger

2 Answers

Gear link or box problem


Sounds like a piece of linkage came loose. If it were an internal tranny problem, doubtful that the stick would be loose. Examine all linkage for something very obvious.

Oct 07, 2009 | 2005 Volkswagen Microbus

Not finding what you are looking for?
2005 Ford Ka 1.3 Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...