Question about Cars & Trucks

1 Answer

Need a torago van manual

Need advice on over heating problem

Posted by on

  • ann white Nov 09, 2012

    all good friend helping



1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Buy manual.

Posted on Nov 08, 2012


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

The open door indicater is stuck on & it stays on when ignition is off on my 1999 torago

Hi Darren, Im AL the owner of Big As Auto Repair.

Darren most likely you have a defective door ajar switch causing the computer to see that door open all the time and turning on the light. Most are built into the door latch, some are on the body of the car, so you'll need a latch for the door that's causing the issue or a switch that mounts into the door opening on the body. The parts people will know which one you have. Hope this helps and should you find the time please visit my auto-repair-website HERE:

Oct 24, 2016 | Cars & Trucks

2 Answers

Cyl head gasket replacement on a Nissan Duke HR16 vvti engine 2015

best advice is to get a workshop manual for the engine
heads can generally be removed in car
next set the valve timing before removing the belt. check and record the position of the cam timing marks
don't move the crank after the head is pulled

Oct 02, 2016 | Cars & Trucks

1 Answer

Temperature gauge staying on C

first thing i would do is the simplist, and change the thermostat. if that doesnt help, then you may need to backflush the heater core, because sometimes these will plug up.

Jan 22, 2013 | 2006 Dodge Caravan

1 Answer

Oxygen Sensor Replacement 1988 Chevy G20 Van 5.7 350

You'll need to crawl under the van and look at the exhaust pipes before the catalytic converter. You will see it once you take a peek.

Nov 26, 2012 | Cars & Trucks

1 Answer

Is there an electronic choke on the side of a carby on a toyota torago 1990 model and if so can it stick open?

Hi, All the engine funtions are controlled by the computer(ECU). The only thing you maybe able to change is the idle speed. There is no carb. but there is a throttlebody EFI. Good luck.

Sep 15, 2011 | Toyota 4Runner Cars & Trucks

1 Answer

I need a heater hose routing diagram for a 1989 Chevy G30 Van with rear heat

The hoses dont matter which way you install them, they just run up the frame to the intake, and water pump outlet the water pump is the pressure side and the intake is the return, if you need any other advice just ask, and please rate or leave feedback

Jul 31, 2011 | Chevrolet G30 Cars & Trucks

1 Answer

I have no heat in the van-no blower or heat. Is

there are several probable cause it may be a fuse blown, resistor block which you can check for continuity or a blower motor prob.These things need to be checked one at time

Jan 30, 2010 | 1996 Ford Econoline

1 Answer

No heat

As for the fan your blower resistor is in need of replacement.
To address the heat problem I'll need to know a couple of things
1. Does your vans temp gauge read in the normal range or is it running low(after you've driven it for at least 10 min
2. Is the out side temp really cold?

Jan 16, 2009 | 2002 Chevrolet Astro

1 Answer

Blower squeals when van is turned on, not much heat comes out

the blower is going out .needs to be replaced,

Jan 10, 2009 | 1997 Chevrolet Astro

1 Answer

My 1995 ford areostar van when heat is on only blows cold air

The aerostar has a vacuum operated watervalve in the heater tubing.the valve is located on the
passenger side inner fender behind the aircleaner.with someone operating the controls inside the van
you can check to see if you get vaccum by removing the tiny hose that goes to the water valve
and checking for suction as you in the van person operates the heater cont If you have no
vaccum there is a break in the hose between the intake manifold and the valve. If you do get
vaccum check to see if the valve changes position from vaccum on to vaccum off. you can see
this motion on the small lever on the side of the valve. If the valve lever doesn't move you can
move it manually to allow the water to flow through the heater core. if the valve won't move manually
there is an obstruction in the valve. If it does move manually the vaccum diaphragm is gone.
replace the valve. if it moves to the manual open position you can hold it open with a tywrap.
before you get to this point you should first check to see that there is enough coolant in the
radiator. If you still have no heat you can check the coolant flow through the heater core. to do
this remove both heater hoses from the valve and pump water from a hose into one of the hoses
water should flow from the other hose. If it doesn't the heater core is blocked. The rear heater
operates the same way with the watervalve under the van just behind the drivers seat.
Good luck.

Dec 02, 2008 | 1995 Ford Aerostar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides