Question about 1997 Buick LeSabre

Open Question

1997 Buick LeSabre cruise control will not engage

"Cruise" light in dash comes on after pressing and releasing "Set/Resume" slide switch, but control does not take over throttle as I remove my foot from the gas pedal. This went out gradually. For a while it was hit-or-miss. Sometimes it would engage and others it would not.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: Replace Cruise Control Switch in Steering Wheel

I am describing the procedure for the "On/Off" switch, I did not try the one you mention. Buy the switch anywhere ( about $15 ), then use a sharp tool ( small knife, screwdriver, anything ) to gently pry the old one from its socket. It is not glued or screwed in or anything, just squeezed tightly in the socket. Once the switch is out, pull the cable, connect it to the new one, insert back in the socket and press gently. No force necessary, it comes out easily.

Posted on Jul 14, 2008

Ad
  • 56 Answers

SOURCE: 2001 buick LeSabre cruise control

no not a fuse may be the switch itself this is common and parts are not badly priced. replace the switch. It just pops out. The directions will tell you to take out the airbag first but it will sneek out of there.

Posted on Feb 13, 2009

Murphybanton
  • 2004 Answers

SOURCE: BROKEN CRUISE CONTROL 2002 BUICK RENDEZVOUS

A fuse is broken. Let an expert check to determine this.

Posted on Apr 10, 2009

honeymokey
  • 3113 Answers

SOURCE: How do your remove the switch for the cruise 2002 LeSabre

Pull

Posted on Jul 06, 2009

  • 408 Answers

SOURCE: Cruise Control - 1996 Buick Lesabre

Finally got mine fixed. It was a faulty Cruise Control Module..

Posted on Feb 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Intermittent Cruise Control Issue - cuts out when small bump in road is hit and may or may not re-engage after that.


Check the wire connector that plugs into the cruise control under the hood. Sounds like a loose connection. Remove the and reinsert the wire connector several times to make a better connection. Stepping on the brake pedal disengages the cruise control by a switch on the brake pedal, not the computer.

Jan 09, 2016 | 2004 Buick Rendezvous

1 Answer

Where is the fuse for cruise control on a 2003 envoy


It is HVAC 1fuse #39 in the rear fuse block ,this powers the on/off switch for cruise control ! Fuse Block - Rear Beneath the left rear seat. What engine does it have ? 4.2 L or 5.3 l There is no vacuum involved in the operation of the cruise control ! Your vehicle has electronic throttle control .
Cruise control is a speed control system that maintains a desired vehicle speed under normal driving conditions at vehicle speeds above 40 km/h (25 mph). Steep grades may cause variations in the selected vehicle speeds.
The following are the main components of the Cruise Control System:
?€¢
The powertrain control module (PCM)


?€¢
The On/Off switch


?€¢
The Resume/Accel switch


?€¢
The Set/Coast switch


?€¢
The TCC brake switch


?€¢
The stop lamp switch


?€¢
The throttle actuator control (TAC) motor


?€¢
The vehicle speed sensor


Cruise Control Engaged
The cruise control system will engage and adjust the vehicle speed based on the activation of the following cruise control switches:
?€¢
On/Off


?€¢
Resume/Accel.


?€¢
Set/Coast

The cruise control switches are located on the multifunction/turn signal lever.
The powertrain control module (PCM) monitors the signal circuits of the cruise control switches in order to determine when to capture and maintain the selected vehicle speed. The PCM uses the throttle actuator control (TAC) module motor in order to control the vehicle speed. For further information on the TAC System, refer to Throttle Actuator Control (TAC) System Description in Engine Controls - 4.2 L.
Ignition positive voltage is supplied from the 10 ampere HVAC 1 fuse to the cruise control switch via the ignition 3 voltage circuit. When the normally open cruise control On/Off switch is turned On, the switch closes and the PCM detects a high signal voltage on the cruise control on switch signal circuit. When the normally open Set/Coast switch is pressed, the switch closes and the PCM detects a high signal voltage on the cruise control set/coast switch signal circuit. To engage the cruise control system, turn the On/Off switch On and momentarily press the Set/Coast switch. The PCM will confirm that the cruise control enable criteria has been achieved. The PCM will engage the cruise control system and record the selected vehicle speed. The PCM sends a class 2 message to the instrument panel cluster in order to illuminate the cruise control indicator. Pressing the accelerator pedal, while the cruise control system is engaged, will allow the driver to override the cruise control system in order to accelerate the vehicle beyond the current set vehicle speed. When the accelerator pedal is released, the vehicle will decelerate and resume the current set vehicle speed. The driver can also override the current set vehicle speed via the Set/Coast switch and the Resume/Accel switch. When the cruise control system is engaged, pressing and holding the Set/Coast switch will allow the vehicle to decelerate from the current set vehicle speed without deactivating the cruise control system. When the Set/Coast switch is released, the PCM will record the vehicle speed and maintain the vehicle speed as the new set vehicle speed. When the cruise control system is engaged, momentarily pressing the Set/Coast switch will allow the vehicle to decelerate at 1.6 km/h (1 mph) increments for each time that the Set/Coast is momentarily pressed, with a minimum vehicle speed of 37 km/h (23 mph). When the normally open Resume/Accel switch is activated, the switch closes and the PCM detects a high signal voltage on the cruise control resume/accel switch signal circuit. Activating and holding the Resume/Accel switch, when the cruise control system is engaged, will allow the vehicle to accelerate to a greater vehicle speed than the current set vehicle speed. When the Resume/Accel switch is released, the PCM will record the vehicle speed and maintain the vehicle speed as the new set vehicle speed. When the cruise control system is engaged, momentarily activating the Resume/Accel switch will allow the vehicle to accelerate at 1.6 km/h (1 mph) increments for each time that the Resume/Accel switch is momentarily activated, with the maximum acceleration total of 16 km/h (10 mph) over the current set vehicle speed . Momentarily activating the Resume/Accel switch, after the cruise control system has been disengaged by pressing the brake pedal, will recall the previous set vehicle speed that is recorded in the PCM.

Sep 11, 2015 | Cars & Trucks

4 Answers

2005 Chevy trailblazer ext problems 1. Cruise will not set.worked last on 4/12/15 2. While checking fuses for CC problemdome lights stopped working, but worked fine before checking fuses. PLEASE HELP!


Bummer deal! This may be a way to tell you some tail lights are burnt out. Some cruise controls have a fuse in a second location.
The fuse is not in right or is blown. Check with a new fuse. Hope this helps. ...gc http://www.auto-tune-up-and-repair-options.com/

Apr 20, 2015 | 2005 Chevrolet Trailblazer Ext

1 Answer

I have a 2008 Honda CRV and for the life of me I cannot engage the Cruise control- I press the Cruise Button on the right of the steer wheel and nothing happens - nothing Help anyone ? Tks Nancy


The cruise-controls have 2-buttons that must be activated before it gets the car going when you remove your foot off the gas-pedal.
The cruise button is essentailly a switch that turns 'on' the cruise servo-motor that tells the sytems that you wants to use it, so it gets ready.
There are other three switches on the right-side of the steering wheel namely: resume accel; cancel; set decel.
To get your car to cruise: you must steady your speed and foot on the gas-pedal. You cannot just press the switches and expect the car to cruise. It takes about two-to-three seconds for the system to respond to a set cruising speed.
How to do it: accelerate to a speed of about 30-mph. Press the 'cruise' button on the dash first. Next you press 'set decel' button. This will turn 'on' the cruise control light on the instrument panel. Then wait a second or three and you would feel the cruise engagement. Any touch on the brake pedal will slow down the car and turns the cruise off. The 'cancel' button turns off the cruise light on the instrument panel.
If you hit the brake-pedal at any time for any reason, and you would like to continue cruising again, simply press the 'resume accel' button.
The cruise system works in conjunction with the braking system of the car. So all major parts of the braking system must be in good condition, otherwise the cruise system could shut off itself.





Sep 28, 2009 | Honda CR-V Cars & Trucks

1 Answer

Cruise control indicater lights are on but will not engage


Check the cruise control module connector, see if it looks good and there is power to the module over one of the white wires in the 10 pin connector.
There are two white wires going to the module which is located at pins "G" and "J". There should be no voltage at pin "G" until the brake switch is applied. This switch is also used to operate the brake lights. The two wire colors on this switch are white and orange. At pin "J", this signal goes to the PCM to tell it that the cruise control module is engaged. Here is the info on the cruise control connector:

Pin A: gray - cruise control on switch signal: 12VDC with cruise switch on
Pin B: dark blue - cruise control set/coast switch signal: 12VDC with switch pressed
Pin C: gray/black - cruise control resume/accel switch signal: 12VDC with switch pressed
Pin D: brown - cruise control release signal: 12VDC with brake pedal not pressed: 0V when pressed
Pin E: black/white - ground
Pin F: brown - ignition 3 voltage: 12VDC with ignition on
Pin G: white - stop lamp switch signal: 0V with brake pedal not pressed: 12VDC when pressed
Pin H: dark green - cruise control inhibit signal: 0V if PCM detects an inhibit condition
Pin J: white - cruise control engaged signal: voltage (unsure of value, either 12VDC or 5VDC) when signal engaged
Pin K: dark green - vehicle speed signal: 1 to 5 volts depending on speed

This view of connector is facing it after it is separated.

Trying to post the connector view, the lines may not quite line up, but at least it should show you the pin positions.

| F  G H J K |

| E D C B A | 

May 09, 2009 | 2002 Chevrolet Impala

1 Answer

Replace Cruise Control Switch in Steering Wheel


I am describing the procedure for the "On/Off" switch, I did not try the one you mention. Buy the switch anywhere ( about $15 ), then use a sharp tool ( small knife, screwdriver, anything ) to gently pry the old one from its socket. It is not glued or screwed in or anything, just squeezed tightly in the socket. Once the switch is out, pull the cable, connect it to the new one, insert back in the socket and press gently. No force necessary, it comes out easily.

Jun 14, 2008 | 2002 Buick LeSabre

Not finding what you are looking for?
1997 Buick LeSabre Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...