Question about 2007 Mitsubishi Endeavor

1 Answer

How to remove old lift gate struts and replace

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mitsubishi Master
  • 76,846 Answers

Watch the video on the job below, all of the gas lights are the same no matter the model.

Posted on Nov 08, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: 2004 endeavor trunk

Today is your lucky day. Get inside of your vehicle to open the lift gate and then open the glass from the inside as well . From the outside of the vehicle with the gate down and the glass open you will see the cover on the glass held in place by two screws. Remove this cover to expose the micro switch for the glass opening handle. You will see a small white connector and with a little patience you can remove this connector. If the glass switch is bad your hatch will now open and your glass should close without having to lock the locks. The switch is a dealer item and goes for around $50 and a bit more dissassembly of window to replace switch/Handle. Happened to me and cost 100 just for them to tell me what was wrong. I used a stick to poke the safty latch for almost two yrs

Posted on Sep 27, 2008

motor1258
  • 6674 Answers

SOURCE: rear strut removal

Check this link & scroll down to 1994-2000 models.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800382b2

Posted on Jan 31, 2009

jmgldsmth
  • 1889 Answers

SOURCE: Replacing Engine Air Filter in 2004 Endeavor

No it's just is hard to pull out; be sure you place the new filter in with the arrows facing the engine intake this assures that you did not put it in upsidedown

Posted on May 21, 2009

  • 3 Answers

SOURCE: Cabin Air Filter - 2004 Mitsubishi Endeavor (Where?)

IT IS IN BEHIND THE GLOVE COMPARTMENT YOU HAVE TO TAKE IT OUT BY UNSREWING AND START FROM YOUR RIGHT SIDE

Posted on Jun 10, 2009

  • 333 Answers

SOURCE: lift gate does not work in 2004 mit endeavor

This is due to the microswitch inside the glass hatch failing. It will not let you open the door because it is unsure if the glass is open or not.

Here is how to verify this:

Manually open the glass hatch.
Remove the two philips screws from the cover on the back of the handle area, and unscrew the plastic plug with the slot in it.
You should now be able to remove the cover.
You will see the harness coming off the glass handle going to a connector. Unplug this white two wire connector.
Your rear hatch should now open normally, just without glass opening.

To repair this, you will need to replace the glass hatch handle. It is a dealer-only part, and the cost is about $35.

To replace it, simply remove the 2 10mm nuts behind it (visible with the cover off that you just removed) and replace the handle and plug it back in.
Now all functions will work.

If you have any questions, just ask :)
If this has been helpful please be sure to rate me :)

Posted on Sep 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove stabilus lift-o-mat liftgate


Most of these lift struts can be removed by propping up the gate and prying off the strut ends from their balljoint ends. Some struts have a broad metal band that acts as a spring or retainer and you may have to slide that band off and then pop the old strut off.
To put the new one on, just center the socket over the strut and press it on or tap it with a small hammer. Make sure you put it on with the strut body either up or down the same way as the one you took off. Normally the body goes to the car and the shaft to the tailgate/hatch/trunk.

Jul 12, 2014 | 1998 Chrysler Sebring

1 Answer

Rear lift gate struts


The new ones will have instructions with them.
Be blessed.

Jan 02, 2014 | 1999 Mitsubishi Montero Sport

1 Answer

Looking for instructions on replacing the rear gate support struts on a 2008 Chevy Equinox


It is very simple. All you need to do the job is a small screwdriver or pick. Open the lift gate. (it may be helpful to get someone to help you hold it open while you are working.) Use the screwdriver or pick to lift the spring clip from the ball end of the lift strut and pull the lift strut off of the ball mount. Repeat this for the other end of the lift strut. The new struts should have new clips already in place. Simply push the ball ends of the new lift strut onto the ball mounts until they "click" into place.

Repeat the proceedure for the other lift strut if you are replacing both of them.

Sep 03, 2011 | Chevrolet Equinox Cars & Trucks

1 Answer

I am replacing the tailgate strut that failed and can't get the trim cover off to snap out the bottom of the strut.


In the lift gate inside trim panel you will see a plastic cap plug at the door latch area. Remove the plug to gain access to the latch.You will see the plastic plug cap at the bottom of the inside lift gate trim panel. ----------- Click this link below for more details:--- http://technoanswers.blogspot.com/2011/07/how-to-remove-tailgate-strut-on.html --------- This should help.Thanks.Helpmech.

Jul 20, 2011 | 2006 Cadillac SRX

1 Answer

How to replace gas lift for back gate


depends on what model you are asking about . some of the rear lifte gate struts are bolted on . just remove the bolts while supporting the real glass or lift gate .And some struts use a little push clip at each end of the strut . these you can use a pick or a small flat blade screw driver to pop out of place . the new struts should have them already installed on them . so they just snap back on . just remeber to support the gate while changing the struts

Mar 06, 2011 | GMC Envoy Cars & Trucks

2 Answers

2005 grand cherokee hood strut won't hold hood up.Brand new . Only has one strut.


Sounds like the new strut is either upside down or defective. When you purchase these make sure you get a hood support not a lift gate. The lift gate ones are for a much lighter rear hatch and will not support a hood.

Oct 13, 2009 | 2005 Jeep Grand Cherokee

2 Answers

I have a 2007 yukon and the lift gate goes up about half way and returns to the closed position. What is going on?


try removing your shocks/struts for the lift gate. once removed, check to see if they fully extend in and out of the barrel. You may have bent shocks/struts. Also, check to see there is nothing preventing the lift-gate from opening such as a bolt or acorns between the spoiler and the roof...

Jul 17, 2009 | 2007 GMC Yukon Denali

1 Answer

Liftgate opens only partially on 2007 tahoe


try removing your shocks/struts for the lift gate. once removed, check to see if they fully extend in and out of the barrel. You may have bent shocks/struts. Also, check to see there is nothing preventing the lift-gate from opening such as a bolt or acorns between the spoiler and the roof...

Jun 22, 2009 | 2007 Chevrolet Tahoe

Not finding what you are looking for?
2007 Mitsubishi Endeavor Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...