Question about 2004 Chrysler Crossfire

Open Question

Brake rotor removal front and rear

I want to repair my crossfire front and rear brakes and rotors removal and installation. please help. Vernon

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 142 Answers

SOURCE: PULSATION WHEN APPLY BRAKES

Even though you replaced the rotors, seems that you will still need to have them resurfaced. This assuming you are experiencing pulsation only when braking.
Hope this helps, Please remember to rate this answer.

Posted on Feb 12, 2009

Ad
hunterd777
  • 14 Answers

SOURCE: Early wear on front brakes /rotors for 2008 Town and Country

I work for a brake repair shop and trust me you are not alone.Enterprise and alot of other people bought the same van and had the same trouble.I hate to say but it doesnt stop there.About every 14 to 15 thousand miles you have to replace the front pads.As of now they dont have an upgrade,for instance ceramic pads, but I am sure they will very soon

Posted on May 01, 2009

  • 770 Answers

SOURCE: i have 2006 chrysler town and country 6 cylinder,

The pulsating can be one of 2 problems, they feel very different, unfortunately, I can not feel what you feel, so here goes. One problem could be with your abs system, possibly diagnosed with an OBD II reader, the other could be warped rotors, but not likely since you replaced. Good Luck! I hope you find this to be very helpful!

Posted on Dec 23, 2009

  • 191 Answers

SOURCE: 2006 town and country rear brake rotor removal

yes the e brake shoes inside the rotor tend to create a lip that will hang them up just bake them off a bit and you should be able to pull them off fairly easily also check to be sure that the stock assembly line retainer clips have been removed from the front of the rotor they are just thin looking washers that are pushed on to the lug nut studs to hold the rotor in place on the assembly line a pair of side head cutters work well to remove them and discard after removed.
Hope this helps.

Posted on Feb 13, 2010

  • 2 Answers

SOURCE: Front brakes lock up causing hot and smoking front brakes.

I have 1999 ply voager The front passager brake will stick and get hot.I took it to a shop, They replace the both calb and passager brake line. It was fine for a few days and then the front passager did it again, I took it back to them they bleed the line again but it still does it. I called them they said to bring it back in and they will change out the passager calb it could have been bad even know its new. Does anyone know what would cause this

Posted on Jan 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove crossfire front brake rotors


front rotor removal you need to remove the brake caliper including the brake caliper bracket so nothing is in the way, there should be a 7mm set screw in the rotor remove that, then get some pb blaster and spray the center part of the hub and the back part of the hub very liberally then you have to use a hammer and beat it off, a way to make it easier is to rotate the rotor as you beat it. It will come off.

Sep 27, 2011 | 2005 Chrysler Crossfire

1 Answer

How to change the rear brakes and rotors..?


. Removal & Installation Front Front brake caliper & rotor removal/installation mitsubishi-09-00-7842.gif

Rear Rear brake caliper & rotor removal/installation mitsubishi-09-00-7843.gif

prev.gif next.gif

Dec 19, 2010 | 2005 Mitsubishi Galant

1 Answer

2007 uplander rear brake repair - what type of brake pads came as original equipment? Ceramic or semi-metalic? The dealer service states that the original were semi-metalic. I've replaced the front...


pads last about 20k, rotors about 40,for the fronts and about 30/50 for the rears,they are all semi metallic.if you look under the car you will see the places for the jack(not to be used when working on the car OTHER than replacing a tyre.)for all manuals see "manuals"on this website(i am in england...)

Sep 29, 2010 | 2007 Chevrolet Uplander LT Minivan

1 Answer

How to take back rotors off a 1994 honda civic.


PATH: Brakes > Front Disc Brakes > Brake Disc (Rotor) > Removal & Installation Removal & Installation
  1. Raise and support the front of the vehicle on jackstands. Remove the front wheels.
  2. Remove the caliper assembly; do not let the caliper assembly hang by the brake hose, instead support it with a piece of wire looped around the front spring or control arm.
  3. Remove the retaining screw from the brake rotor and remove the rotor from the hub.

An impact driver, No. 3 phillips screwdriver bit, and a hammer may be needed to remove the retaining screw. It is fairly easy to destroy the screw slots using an ordinary phillips screwdriver to remove the tightly driven screw (see photo).

  1. To install the disc, replace the disc on the hub, screw in the retaining screw and replace the caliper assembly.
edc2fe7.gif
PATH: Brakes > Rear Disc Brakes > Brake Disc (Rotor) > Removal & Installation Removal & Installation
  1. Raise and safely support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Disconnect the caliper from the caliper bracket. Support the caliper out of the way with a length of wire. Do not allow the caliper to hang from the brake hose.
  4. Remove the caliper bracket.
  5. Remove the two 6mm screws and the brake disc. If the brake disc is difficult to remove, install two 8mm bolts into the threaded holes and tighten them evenly to prevent cocking the rotor.
  6. Install the rotor in position. Install the two 6mm retaining screws.
  7. Install the brake caliper. Install the tire and wheel assembly.

PATH: Brakes > Rear Disc Brakes > Brake Disc (Rotor) > Removal & Installation Removal & Installation
  1. Raise and safely support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Disconnect the caliper from the caliper bracket. Support the caliper out of the way with a length of wire. Do not allow the caliper to hang from the brake hose.
  4. Remove the caliper bracket.
  5. Remove the two 6mm screws and the brake disc. If the brake disc is difficult to remove, install two 8mm bolts into the threaded holes and tighten them evenly to prevent cocking the rotor.
  6. Install the rotor in position. Install the two 6mm retaining screws.
  7. Install the brake caliper. Install the tire and wheel assembly.

4d85ad3.gif

Sep 15, 2010 | 1994 Honda Civic

1 Answer

Need instructions for installing parking brake shoes on a 2001 Dodge 3500 pickup


This is a big job for such a small part. I suggest you repair/replace rotors, pads, and anything else back there while you are at it. You will need to remove both wheels on both sides, as well as the axles (I think). See my earlier post on Rear Rotor removal to see how this is done.

You will need a large spindle nut to remove the axles.

DISASSEMBLY:
Once you have access to the parking brakes inside the rotor hat:
1. Lock out the parking brake w/a pair of Vise grips (on the parking brake cable under the cab)
2. Disengage teh park brake cable from behind the rotor assembly to allow easier disassembly of the parking brake shoes.
3. Disassemble the rear park brake shoes.

REASSEMBLY:
1. Reassemble the rear parking brake shoes. This is a typical, small brake drum configuration. Do one side at a time - so you can see how to reassemble each small part. Keep the springs and parts oriented the same: front to front and interior to interior, etc.
2. Release the parking brake cable
3. Install the disc brake rotor(s)
4. Install the disc brake caliper(s)
5. Install tire & wheel assembly
6. Lower the vehicle

Sep 07, 2010 | 2001 Dodge Ram 3500 Truck

2 Answers

When buying rotors for a 95 Bronco 4X4 should the rotors be seperate from the hub or should they be attached as one piece? Im getting mixed info from part stores.


The reason you're getting mixed info from parts stores is because it comes both ways.
Look at the following to determine which one you have, 4 wheel disc brakes (floating front rotors) or rear drum brake model (except 4 wheel disc brakes):
Brake Disc (Rotor) REMOVAL & INSTALLATION Except F-Super Duty with 4-Wheel Disc Brakes Fig. 1: Secure the caliper so there is no tension on the brake hose 88289p22.jpg
  1. Jack up the front of the truck and support it with jackstands. Remove the front wheel.
  2. Remove the caliper assembly and support it on the frame with a piece of wire (or something equally secure) without disconnecting the brake fluid hose.
  3. Remove the hub and rotor assembly.
  4. Install the rotor in the reverse order of removal, and adjust the wheel bearing as outlined in Section 1.
F-Super Duty with 4-Wheel Disc Brakes The hub and rotor are individual pieces, allowing the rotor to be replaced independently. The front and rear rotors are the same and are attached with 10 bolts and washers. The bolts are tightened a little at a time, in a crisscross fashion, to an ultimate torque of 74–89 ft. lbs. (100–121 Nm). prev.gif next.gif

Sep 03, 2010 | 1995 Ford Bronco

2 Answers

How to remove brake rotors on a 1996 ford explorer


How to replace the rear brake pads on a 1995 through 2001 Ford Explorer The system utilizes a drum-in-hat type rear brake rotor. The integral drum allows the use of a drum-and-shoe type parking brake system. All other components are similar to their front disc brake components Remove the two bolts on either side of the brake hose with the rubber boots. Do not remove the four bolts where the axle ties in. The two bolts to be removed require a 10mm socket/wrench. Loosen the pads from the caliper Rotor Removal In order to take the rotors off (replace with new or have them machined), it is best to loosen the emergency brake shoes. To do this, behind the rotors, in the back there is a rubber plug, remove that and you can use a screw driver to engage the teeth of the adjusting screw, turn it clockwise to loosen, usually 10-20 teeth. Usually this means turn it downward. After this, it may still be difficult to get the rotors off without tapping them. Use a rubber mallet and hit them from behind. Before really whacking the rotor, make sure you have loosened the adjusting screw enough. It may take heavy swings of the rubber hammer to do this. It will eventually break loose. Parking Brake You might want to check the parking brake while you are here. To remove:
  • Remove the rear disc brake rotor.
  • Remove the outboard return spring.
  • Remove the adjusting screw spring.
  • Remove the rear brake shoe hold-down spring and pin.
  • Remove the brake shoe adjusting screw and nut.
  • Remove the front brake shoe hold-down spring and pin.
  • Remove both parking brake shoes and the inboard return spring.
  • Check the parking brake lever for excessive wear and replace as necessary.
To install:
  • Position the front parking brake shoe to the backing plate and install the hold-down pin and spring.
  • Install the rear parking brake shoe with the inboard return spring.
  • Position the brake shoe adjuster screw and nut on the shoes and install the rear shoe hold-down pin and spring.
  • Install the brake shoe adjuster spring.
  • Install the outboard return spring.
  • Adjust the parking brake shoes and install the rotor, caliper and wheel.
  • Lower the vehicle and tighten the wheel lug nuts to 100 ft. lbs. (135 Nm).
ADJUSTMENT
  • Measure the inside of the drum portion of the rear brake rotor
  • Remove the rear disc brake rotor.
  • Using Brake Adjustment Gauge D81L-1103-A or equivalent, measure the inside diameter of the drum portion of the rear disc brake rotor.
  • Subtract 0.020 in. (0.508mm) from the first measurement, adjust the brake shoes to that size
  • Adjust the parking brake adjuster screw until the outside diameter of the parking brake shoes measures 0.020 in. (0.508mm) less than the drum measurement.
  • Install the rear disc brake rotor.
Reassembly Reassembly is easy. Put new or machined rotors back on by sliding them over the lugs (they should slide on easily.) Loosen bleeder valve (having a catch bottle handy is good). Push calipers in slowly (using a c-clamp or large channel lock pliers), close bleeder valve. Put on pads. Lubricate metal clips with small amount of anti-seize. Re-adjust the emergency brake by turning the opposite direction from loosening. Refill the brake master cylinder

Aug 09, 2010 | 1996 Ford Explorer

1 Answer

Can'tremove the rotors on my mitsubishi 2008 Eclipse Spyder GT. What am I missing


Brake Rotor Removal & Installation Front Front brake caliper & rotor removal/installation mitsubishi-09-00-7842.gif

Rear Rear brake caliper & rotor removal/installation mitsubishi-09-00-7843.gif

prev.gif next.gif

Jul 31, 2010 | Mitsubishi Spyder Cars & Trucks

1 Answer

Replace rear brake pads


Rear disc brake pads offer better performance and are not as affected by moisture like conventional brake shoe style brakes are. Rear disc brakes are similar to front disc brakes. The main difference is that rear disc brake systems must incorporate the emergency brake system. There are two methods widely used for the emergency brake with rear disc systems. The first system is a brake shoe inside the brake disc that is actuated by the emergency brake lever. The second is a screw style actuator inside the brake caliper. When activated the brake pads are forced into the brake disc and held tightly by the emergency brake lever.
READ COMPLETELY BEFORE STARTING
Step 1 - Identify Rear Disc Brake Components
rear_brake_pads.jpg Rear disc brake assembly includes; rear brake disc, rear brake pads, brake caliper mount and a caliper mounting screw. (Note: Some vehicles do not have the rotor mounting screw.)
Step 2 - Removing the Rear Brake Caliper Mount Bolts
rear_brake_pads_2.jpg To replace rear brake pads and rotors the rear brake caliper needs to be removed. First loosen the rear brake caliper mount bolts and remove them. Turn counter clockwise.
Step 3 - Lift Rear Brake Caliper from The Caliper Mount
rear_brake_pads_3.jpg After the caliper mount bolts have been removed, gently lift the brake caliper from the caliper mount. Inspect the caliper slides; they should move freely in the caliper mount. Remove rear brake pads and hardware.

Step 4 - Removing Caliper Mount Bolts
rear_brake_pads_4.jpg With a socket wrench or other appropriate removal tool, loosen the rear brake caliper mounting bolts. Remove bolts and lift the caliper mount and remove it from the vehicle. Remove the retaining screw from the disc mounting hole. Tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub holding on tightly, using both hands. You do not want to drop the rotor.

Step 5 - Removing Rear Brake Rotor
rear_brake_rotor.jpg Remove the retaining screw from the disc mounting hole, tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub, hold on using both hands and do not drop.

Step 6 - Install New Brake Rotor
rear_brake_rotor_2.jpg Check the new rotor against the old brake rotor to make sure they are the same size. Clean the mating surface on the wheel hub before the new brake rotor is installed. Reinstall rotor retainer screw.
Step 7 - Reset Rear Brake Caliper
rear_brakes_7.jpg Before new brake pads can be installed, the rear brake caliper must be reset. The reset tool winds the piston back into position so the new brake pads will fit. This style of brake caliper will not compress with a clamp tool; it can only be reset with the proper reset tool.
Step 8 - Reinstall Rear Caliper Mount and Install New Rear Brake Pads
rear_brake_rotor_3.jpg After the caliper has been reset, reinstall caliper mounting bolts and make sure the bolts are tight. Then match up the old brake pads to the new brake pads. They should be exactly the same except, of course; the old ones will be worn out. Check the new brake pads for proper fit and install any brake hardware that is required.
Step 9 - Remount Rear Brake Caliper
rear_brake_rotor_4.jpg Reinstall the brake caliper, align brake pad hardware and reinstall caliper mounting bolts. (Note: align the rear peg of the brake pad to the groove in the caliper piston.) Recheck and retighten all caliper and caliper mount bolts. Bleed brake system to relieve any air in the system. Before driving the vehicle, push the brake pedal down and let it up slowly. This operation forces the brake pads to travel to the brake rotors. DO NOT DRIVE VEHICLE until proper brake pedal operation resumes. When test driving vehicle listen for any unusual noises during the operation of the brakes.
WARNING! Always have the vehicle under inspection on level ground, in park with the emergency brake on. Always wear protective eyewear, gloves and necessary clothing before inspection or work begins. Never crank an engine over when anyone is near the battery or engine. Always have an operational fire extinguisher close by, obey all first aid instructions in the event of an injury. Never stand in front or behind a vehicle when cranked over or running. When engine is cranked over keep hands and clothing away from rotating components. Never move a car without proper brake pedal operation.

Jun 01, 2010 | 1995 Saab 900

1 Answer

I need to know the procedure for r and r on a front rotor if this is something that can be done at home with limited tools?


1999 Taurus/Sable Section 06-03: Brakes, Front Disc 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Disc Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Be careful to avoid damage or interference with caliper bleeder screw fitting and front disc brake rotor shield (2K004).
  1. ani_caut.gif CAUTION: Handle front disc brake rotor (1125) and disc brake caliper (2B120) assembly in such a way as to prevent deformation of front disc brake rotor , and nicking, scratching or contamination of brake linings/rotor surfaces.
    NOTE: To prevent damage, do not allow disc brake caliper to hang by the front brake hose (2078) .


    Remove caliper anchor plate bolts and discard. Position disc brake caliper out of the way. Prevent separation of caliper housing from anchor bracket because contamination of guide pin journals can occur.
  1. NOTE: If excessive force must be used during front disc brake rotor removal, the front disc brake rotor should be checked for runout prior to installation.


    If additional force is required to remove front disc brake rotor , apply Rust Penetrant and Inhibitor F2AZ-19A501-A or equivalent meeting Ford specification ESR-M99C56-A on front and rear rotor/hub mating surfaces. First, strike front disc brake rotor between lug bolts (1107) with a plastic hammer. If this does not work, attach 2-3 Jaw Puller 205-D027 (D80L-1013-A) or equivalent and remove front disc brake rotor . Remove front disc brake rotor from wheel hub (1104) assembly by pulling it off the lug bolts.
Installation
  1. If original front disc brake rotor is being installed, make sure rotor braking and mounting surfaces are clean.
  1. ani_caut.gif CAUTION: Failure to clean rust and foreign material from rotor and hub mounting faces when installing new or old front disc brake rotors will result in high rotor runout, which will speed up the development of brake roughness shudder vibration.
    Apply a small amount of Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A or equivalent meeting Ford specification ESE-M1C171-A to pilot diameter of front disc brake rotor.
  1. Install front disc brake rotor on wheel hub assembly.
  1. Install disc brake caliper and new caliper anchor bracket bolts on front disc brake rotor . Tighten caliper anchor bracket bolts to 88-118 Nm (65-87 lb-ft).
  1. ani_caut.gif CAUTION: Failure to tighten lug nuts (1012) in a star pattern may result in high rotor runout, which will speed up the development of brake roughness, shudder and vibration.
    Install wheel and tire assembly on vehicle. Tighten lug nuts to 115-142 Nm (85-104 lb-ft) using Rotunda Accutorq® Lug Nut Socket 164-R0303 or equivalent on a 1/2 inch air impact wrench, or use a torque wrench.
  1. Lower vehicle.
  1. Pump brake pedal prior to moving vehicle to position brake linings.
  1. Road test vehicle.









May 25, 2009 | 1999 Mercury Sable

Not finding what you are looking for?
2004 Chrysler Crossfire Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...