Question about 2003 Land Rover Discovery

1 Answer

Replacing tag light assembly on 03 LR Discovery

It appears you have to remove panel on inside of rear door to access mounting bolts but I don't want to mess anything up.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 149 Answers

Nope, it's held in by two screws on each light IIRC, undo these and the light assembley will be able to be wiggled out to change the bulb. Repeat for the other side.

Posted on Feb 23, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Undo stripped screw on rear light panel


Stripped head or threading on screw itself?

Nov 09, 2013 | Land Rover Cars & Trucks

1 Answer

How do i replace the rear view mirrors mounted on the doors on a 1999 beetle? Both are loose and floppy and when i remove the plastic housing on each i can see the tension spring is broken, also a star...


Hi,first u need to remove the inside cover on the inside of the door to access the screw for the mirror,but u also need to remove door panels so on the door panel there are screws at the bottem of panel and at the door handle to get to them u need to unclip the handle trim.hope u get it done

May 21, 2011 | 1999 Volkswagen Beetle

1 Answer

How to remove and install the driver side window (just the glass) on a 94 honda prelude


Hi!!
Here is how:
REMOVAL & INSTALLATION
See Figures 1, 2, 3, 4, 5 and 6
  1. Remove the door pad and inner moisture barrier.
  2. If working on the rear window of a sedan, remove the two upper screws securing the center channel. Remove the two lower bolts (in the door) securing the channel and remove it. On some cars, the two screws are concealed below the weatherstrip.
  3. For sedan rear doors, remove the quarter glass. The entire glass and rubber seal may be removed as an assembly from the door.
  4. Lower the door glass until the glass mounting bolts are accessible. One will be easily seen in the large access hole in the door; the other will appear in the smaller, round access hole. Remove the bolts.
  5. Stand next to the inside of the door. Tilt the door glass and remove it through the slot.
  6. On front doors, remove the bolts securing the front run channel, then remove the channel.
  7. Remove the regulator mounting bolts and remove the regulator. On later models, there are additional roller guide bolts to be removed. Mark the roller guide mounting bolts to ease window alignment later.
  8. For power windows, remove the motor from the regulator if desired.
CAUTION The regulator gear will move suddenly when the motor is removed due to action of the large spring. Keep hands well clear.
TO INSTALL, REVERSE DIRECTIONS
FIG 1 1kbron_122.gif

FIG 2 1kbron_123.gif
FIG 3 1kbron_124.gif

FIG 4 1kbron_125.gif

FIG 5 1kbron_126.gif

FIG 6 1kbron_127.gif

Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa!!

Feb 16, 2011 | 1994 Honda Prelude

1 Answer

The left rear door window fell off the track. How do I remove the door panel to access it.


This is the complete procedure you stop when you see the problem.



1. REMOVE REAR DOOR INSIDE HANDLE BEZEL


(a) Remove the screw.


(b) Using a screwdriver with its tip taped, disengage the 2 claws A.


(c) Pull out the the rear door inside handle bezel in the direction indicated by the arrow, disengage the claw B, and remove the rear door inside handle bezel.


2. REMOVE DOOR PULL HANDLE


(a) Using a screwdriver wrapped with the protective tape, disengage the 2 clips and remove the door pull handle.


3. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


(a) Remove the screw.


(b) Disengage the 7 clips.


(c) Disconnect the connector and pull up on the rear door trim board sub-assembly to remove it.


4. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


(a) Remove the bolt.


(b) Disengage the 2 claws and separate the rear door inside handle sub-assembly.


(c) Disconnect the 2 cables and remove the rear door inside handle sub-assembly.


5. REMOVE REAR SPEAKER


6. REMOVE REAR DOOR SERVICE HOLE COVER


(a) Disconnect each connector and remove the rear door service hole cover.


HINT:


Remove the remaining tape on the door side.


7. REMOVE REAR DOOR GLASS RUN


(a) Connect the window regulator switch assembly.


(b) Fully lower the door glass.


(c) Remove the rear door glass run.


8. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


(a) Remove the 2 bolts, the screw and rear door window division bar sub-assembly.


9. REMOVE REAR DOOR QUARTER WINDOW GLASS


(a) Pull out the direction indicated by the arrow, remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit.


10. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP


11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


(a) Remove the rear door glass sub-assembly as shown in the illustration.


(b) Disconnect the window regulator switch assembly.


12. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


(a) Disconnect the connector.


(b) Loosen the temporary bolt.


NOTICE:


If the temporary bolt is removed, the rear door window regulator may fall and become deformed.


(c) Remove the 3 bolts and the rear door window regulator sub-assembly and the power window regulator motor assembly rear as a unit.


(d) Remove the temporary bolt from the regulator.


13. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY REAR


(a) Using a "torx" driver (T25), remove the 3 screws and power window regulator motor assembly rear.


14. REMOVE REAR DOOR LOCK ASSEMBLY


(a) Disconnect the connector.


(b) Remove the bolt.


(c) Using a "torx" socket wrench (T30), remove the 3 screws.


(d) Slide the rear door lock assembly downward, pull out the link from the outside handle frame, and remove the rear door lock assembly and cables as a unit.


(e) Remove the door wire harness packing.


(a) Using a "torx" socket wrench (T30), loosen the screw.


(b) Disengage the 2 claws and remove the rear door outside handle cover.


(a) Disengage the 2 claws and remove the rear door outside handle pad rear.

Jan 03, 2011 | 2006 Toyota Highlander

1 Answer

Replacing the window regulator


Hello,
1.Remove trim from around the door handle by prying it out along the top and front edges. Once loosened, it comes unhinged from the back edge.
2.Remove the Phillips head screw from metal bracket, that is revealed after removing the trim piece
3.Pry the inside light assembly from the door panel and remove the bulb socket from the housing
4.Pry the door panel from the frame using a panel removal tool by starting at the bottom and releasing the 7-8 plastic studs from the frame.
5 - Remove the 2 mounting bolts for the rear door controller and disconnect the cables.
6.Use a small flat blade (e.g. scraper) and flathead screwdriver to remove the plastic vapor barrier (be careful not to tear as it must be replaced).
7.Reach inside the door and locate the cable that is attached to the bottom of the lift mechanism and then cut it.
8.Push the window class to the full UP position (this will locate it horizonally and vertically) and tape it in place.
9.Near the top of the sheet metal there will be 2 openings (1 square, 1 round). When the glass is in the full up position, there will be (2) 10 mm bolts in view. Loosen these bolts which will open the rubber coated clamps on the bottom of the glass. The lift mechanism will free fall to the bottom position when these bolts are loose.
10.Remove the window lift motor plug and (3) 10 mm nuts that hold the lift mechanism in place and remove through the opening at the front of the inner door sheet metal.This will require some maneuvering.
11.Loosen but do not remove the 2 bolts for the window clamps on the new unit before installing.
12.Make sure the new unit is not in the full up position before installing.
13.Install the new lift mechanism in the door and tighten the (3) 10 mm mounting nuts.
14.Connect the power plug into the new lift motor
15.Temporarily connect the rear door controller, turn on the ignition and slowly raise the new lift mechanism using the window up switch on the driver's door.
16.Then the lift is in the full up position, tighten the window glass clamps using the same access holes as when you removed the glass clamps.
17.Slowly run the window down and up to make sure it doesn't bind
18.Disconnect the read door controller and reverse the process for assembly
19. Make sure the rear door light socket and bulb are not trapped behind the plastic.
Hope this was helpful!

Dec 03, 2010 | 2001 Buick Century

1 Answer

Remove the inside rear door panel for 1995 Landrover


Remove the 2 bolts holding the grab handle ( 10mm) Remove the screw holding the pull handle plastic cover and remove the cover. Use a fork and pry the panel away from the door and you will be able to pull it off. Before refitting, check all of the plastic clips that hold the panel to the door, some will have broken off. Remove them and fit them back on to the trim panel and glue them on. Refit is reverse as removal. Hope that helps

Mar 29, 2010 | 1995 Land Rover Discovery

1 Answer

I need to replace LR (driver side) exterior door handle assembly on my Honda Odyssey 2000. I found a source for part but need replacement instruction. Can you help? Thanks, Ed


Have to take off inner door panel and all parts then u will gain access to inside of door remove all linkages and remove bolts from door handle and install in reverse order.

Oct 20, 2009 | 2000 Honda Odyssey

2 Answers

Replacing driver side rear view mirror with housing, non-heated


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Jun 26, 2009 | 1998 Toyota Camry

2 Answers

Need to replace Mirror Assembly, 03 suburban


Your going to have to remove the inside door panel to get to the three bolts that hold the out side mirror assembly. Once you have the door panel off you'll see the three bolts that hold the mirror assembly, just un-bolt and un-clip the wire harness to the electric/heated mirror. To install the new mirror assembly, just do everything in reveres. Go to Auto Zone and by extra door panel clips, there is a good chance of breaking some of the retainer clips and Auto Zone will have the step by step instructions to replacing the mirror assembly and the removal to the door panel. Good luck and keep me posted. Be glad to help.

Jun 22, 2009 | 2001 Chevrolet Suburban

1 Answer

2003 Toyota Sienna - Need to replace left rear brake light


Hi -
I just replaced my left rear brake light on my 2005 Sienna. I followed the manual directions and removed the two metal bolts from the tail light cover. However the assembly did not come off. I could open it a little and it appeared to be bolted from the inside. I looked online but didn't find an answer. I had already gotten pulled over and I didn't want to go to the dealer so I pulled on the assembly a little harder applying even pressure to the top and the bottom and it popped loose. I didn't yank it. There are two metal pegs that have a little lip on them and thats where you are getting the resistance. Hope this helps.

Dec 02, 2008 | 2003 Toyota Sienna

Not finding what you are looking for?
2003 Land Rover Discovery Logo

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

yadayada
yadayada

Level 3 Expert

64052 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...