Question about 1995 Volkswagen Polo 1.4

Open Question

Cylinder head bolt torque settings for VW ABD 1.4 petrol 8 valve engine

ABD 8 valve petrol engine. I would like to know the cylinder head bolt torque settings and the tightening sequence please?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
steve_e_uk
  • 1675 Answers

SOURCE: golf iv 1.6 8v cylinder head torque settings

hi to tighten you have to do it in 4 stages as follows
1st stage 40nm leave 5 mins 2nd stage 60nm leave 5 mins 3rd stage 90 degrees leave 10 mins 4th stage 90 degrees then you are done i will try put order on here i hope this works as follows
10 4 2 6 8 front of engine back of engine 7 5 1 3 9

in that order hope this helps

Posted on May 10, 2010

Ad
alicantecoli
  • 22156 Answers

SOURCE: what is 1996 1.6 8v cylinder head bolt torque settings

80 lbs

Posted on May 07, 2009

morse008
  • 1111 Answers

SOURCE: I need torque settings for 1600 beetle engine SP

wiki this

Posted on Aug 25, 2009

  • 54 Answers

SOURCE: I need the torque sequence for a 1970 vw 1600cc

Imagine that the head bolts are numbered from left to right.  Go 2-3-1-4 and set the wrench to 23 ft/pounds.

Posted on Jun 08, 2010

swoop611
  • 488 Answers

SOURCE: vw jetta 2007 bkd engine whatare cylinder head

I had a quick look online for these specs. according to several sites I visited, these are the correct specs.. Have fun.. 1.8L Turbo

  • Volkswagon's 1.8-liter Turbo engine has 10 head bolts arranged in pairs across the engine. The bolts should first be pre-tightened to a specification of 40 Newton Meters (Nm), starting with the middle two bolts and proceeding in sequence out towards either the left or right end of the engine. The bolts should then be tightened again in the same sequential order by making a one-quarter turn of the wrench, and then tightened once again with another one-quarter turn.
  • 2.8L V6
  • There are 20 head bolts arranged in three lines across Volkswagon's 2.8-liter V6 engine. The bolts should first be pre-tightened in sequence to a specification of 50 Newton Meters (N-m), starting with the first bolt that is situated in the center of the engine block between cylinders 3 and 4. Proceed tightening the bolts in sequence out towards either the left or right end of the engine. The bolts should then be tightened again in the same sequential order by making a one-quarter turn of the wrench, and then tightened once again with another one-quarter turn.
  • 2.0L L4
  • Volkswagon's 2.0-liter L4 engine has 10 bolts that are arranged in pairs across the engine. The bolts should first be pre-tightened in sequence to a specification of 40 Newton Meters (N-m), starting with the middle two bolts and proceeding in sequence out towards either left or right end of the engine. The bolts should then be tightened again in the same sequential order by making a one-quarter turn using a box wrench, and then tightened again with another one-quarter turn.
  • Posted on Dec 19, 2010

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    Need head bolt torque specs for a 1996 saturn sl


    Quote:





    Originally Posted by norvelplagbao52

    1993 saturn sl2 1.9 dohc cylinder head torque
    specs and sequence
    Cylinder head bolt
    tightening procedure:
    CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

    INTAKE
    SIDE
    8 4 1 5 9

    7 3 2 6 10
    EXHAUST SIDE

    In sequence,
    torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
    In sequence,
    torque all bolts. Torque: 50 Nm (37 ft-lbs)
    In sequence, turn each bolt an
    additional 90 degrees.





    Originally Posted by norvelplagbao52

    1993 saturn sl2 1.9 dohc cylinder head torque
    specs and sequence
    Cylinder head bolt
    tightening procedure:
    CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

    INTAKE
    SIDE
    8 4 1 5 9

    7 3 2 6 10
    EXHAUST SIDE

    In sequence,
    torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
    In sequence,
    torque all bolts. Torque: 50 Nm (37 ft-lbs)
    In sequence, turn each bolt an
    additional 90 degrees.

    Sep 19, 2013 | 1996 Saturn SL

    1 Answer

    Correct pressure for torque the head of mazda pickup 1998


    Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.


    Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.



    B2500 4 Cylinder

    Torque sequence: --------- ' 10 6 2 4 8 ' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51 Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final tighten all bolts an additional 90 to 100 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.







    B3000 3.0 6 Cylinder

    Torque sequence ---------- ' 6 4 2 8 ' ' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque to 73 Ft/Lbs









    B4000 4.0 6 Cylinder

    Torque sequence --------- ' 5 1 3 7 ' ' ' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs Step 3: turn cylinder head bolts in sequence an additional 90-degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.


    Good luck with this job!

    Feb 06, 2011 | 1998 Mazda Pickup

    1 Answer

    Want to know the amount of torque pressure do i use when tightening the head bolts, and whats the sequence?


    To install:

    0996b43f80208f65.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Cylinder head bolt torque sequence-3.8L engine

    1. Install the new cylinder head gasket with the arrow pointing to the front of the engine.
    2. Install the cylinder head.
    3. Install NEW cylinder head bolts. Torque the bolts in sequence, as follows:
      1. Step 1: 37 ft. lbs. (50 Nm).
      2. Step 2: Plus 120 degree turn.
    To install:

    0996b43f802316ea.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Tighten the cylinder head bolts using the following sequence-31L and 3.4L engines

    1. Install the cylinder head with a new gasket.
    2. Apply thread sealer to the head bolts.
    3. Tighten the cylinder head bolts to 37 ft. lbs. (50 Nm) plus an additional 90 degree turn.

    Dec 16, 2010 | 2002 Pontiac Grand Prix

    1 Answer

    NEED HELP WITH TORQUE SPECS ON 1998 CHEVROLET SURBURBAN CYLINDER HEADS 5.7


    Cylinder Head Removal & Installation 5.7L Engine To Remove:
    1. Disconnect the negative battery cable.
    2. Drain the engine coolant.
    3. Remove the air cleaner assembly.
    4. Remove the upper radiator hose.
    5. Remove both heater hoses.
    6. Disconnect spark plug wires at distributor cap.
    7. Remove distributor cap.
    8. Remove the coolant bypass hose from the water pump.
    9. Remove the drive belt. NOTE: It is not necessary to evacuate the A/C refrigerant.
    10. Remove the A/C compressor from the mounting bracket and set it aside.
    11. Remove the wiring bracket from the rear of the cylinder head.
    12. Disconnect the accessory bracket and slide forward.
    13. Remove the upper and lower intake manifold.
    14. Remove the exhaust manifolds.
    15. Remove the valve rocker arms and pushrods.
    16. Remove the power steering pump pulley.
    17. Disconnect the electrical connector from the power steering pump.
    18. Remove nuts attaching the power steering pump to the engine.
    19. Remove power steering pump mounting bracket bolts and nut.
    20. Slide power steering pump/bracket assembly forward and remove stud.
    21. Set power steering pump/bracket assembly aside.
    22. Disconnect the wiring bracket from rear of the right cylinder head.
    23. Remove the generator.
    24. Remove the oil indicator tube bracket bolt.
    25. Remove the generator mounting bracket.
    26. Remove the sixteen cylinder head bolts.
    27. Remove cylinder heads and gaskets.
    28. Clean all sealing surfaces.
    To Install:
    Right Side NOTE: Clean all dirt, debris, and coolant from the engine block cylinder head bolt holes. Failure to remove all foreign material may result in damaged threads, improperly tightened fasteners or damage to components.
    NOTE: Do not use any type of sealant on the cylinder head gasket (unless specified).
    1. Clean the cylinder head bolt holes with a thread chaser and compressed air.
    2. Check the cylinder head locating pins for proper installation.
    3. Place a new cylinder head gasket over the engine block dowel pins.
    4. Install the cylinder head to the engine block.
    5. Apply sealant (GM P/N 12346004 or equivalent) to cylinder head bolt threads.
    6. Install the cylinder head bolts. gm-03-50-685.gif

    7. Tighten the cylinder head bolts in sequence on the first pass.
      • Torque to: 22 ft. lbs. (30 Nm)
    8. Using a torque angle meter, tighten the long bolts (1, 2, 5, 6, 9, 10 and 13) on the second pass in sequence to 75°.
    9. Using a torque angle meter, tighten the medium bolts (14 and 17) on the second pass in sequence to 65°.
    10. Using a torque angle meter, tighten the short bolts (3, 4, 7, 8, 11, 12, 15 and 16) on the second pass in sequence to 55°.
    11. Install the valve rocker arms and pushrods.
    12. Install the generator mounting bracket stud.
      • Torque to: 15 ft. lbs. (20 Nm)
    13. Loosely assemble the generator mounting bracket over the stud.
    14. Install all nuts and bolts finger tight.
      • Torque to: 30 ft. lbs. (41 Nm)
    15. Install the generator.
    16. Install the oil indicator tube bracket bolt.
    17. Install the exhaust manifold.
    18. Install the lower intake manifold.
    19. Install the valve rocker arm covers.
    20. Install the wiring bracket to the rear of the cylinder head.
    21. Connect the accessory bracket.
    22. Install the A/C compressor.
    23. Install the drive belt.
    24. Install the distributor cap.
    25. Connect the spark plug wires to the distributor cap.
    26. Install both heater hoses.
    27. Install the upper radiator hose.
    28. Install the air cleaner assembly.
    29. Refill the engine coolant.
    30. Connect the negative battery cable.
    Left Side To Install:
    NOTE: Clean all dirt, debris, and coolant from the engine block cylinder head bolt holes. Failure to remove all foreign material may result in damaged threads, improperly tightened fasteners or damage to components.
    NOTE: Do not use any type of sealant on the cylinder head gasket (unless specified).
    NOTE: Clean all dirt, debris, and coolant from the engine block cylinder head bolt holes. Failure to remove all foreign material may result in damaged threads, improperly tightened fasteners or damage to components.
    NOTE: Do not use any type of sealant on the cylinder head gasket (unless specified).
    1. Clean the cylinder head bolt holes with a thread chaser and compressed air.
    2. Check the cylinder head locating pins for proper installation.
    3. Place a new cylinder head gasket over the engine block dowel pins.
    4. Install the cylinder head to the engine block.
    5. Apply sealant (GM P/N 12346004 or equivalent) to cylinder head bolt threads.
    6. Install the cylinder head bolts. gm-03-50-685.gif

    7. Tighten the cylinder head bolts in sequence on the first pass.
      • Torque to: 22 ft. lbs. (30 Nm)
    8. Using a torque angle meter, tighten the long bolts (1, 2, 5, 6, 9, 10 and 13) on the second pass in sequence to 75°.
    9. Using a torque angle meter, tighten the medium bolts (14 and 17) on the second pass in sequence to 65°.
    10. Using a torque angle meter, tighten the short bolts (3, 4, 7, 8, 11, 12, 15 and 16) on the second pass in sequence to 55°.
    11. Install the valve rocker arms and pushrods.
    12. Install the power steering pump mounting bracket stud.
      • Torque to: 15 ft. lbs. (20 Nm)
    13. Loosely assemble the mounting bracket over the stud.
    14. Install all nuts and bolts finger tight.
      • Torque to: 30 ft. lbs. (41 Nm)
    15. Install the power steering pump pulley.
    16. Connect the electrical connector to the power steering pump.
    17. Install the exhaust manifold.
    18. Install the lower intake manifold.
    19. Install the valve rocker arm covers.
    20. Install the wiring bracket to the rear of the cylinder head.
    21. Connect the accessory bracket.
    22. Install the A/C compressor.
    23. Install the drive belt.
    24. Install the distributor cap.
    25. Connect the spark plug wires to the distributor cap.
    26. Install both heater hoses.
    27. Install the upper radiator hose.
    28. Install the air cleaner assembly.
    29. Refill the engine coolant.
    30. Connect the negative battery cable.

    Aug 31, 2010 | Chevrolet Suburban 1500 Cars & Trucks

    2 Answers

    What r the torque specifications on installing a head on a 1999 yukon and the tightening sequence


    Check this procedure...
    1. Tighten the first design cylinder head bolts as follows:
      1. M11 bolts 1st pass: in sequence to 22 ft. lbs. (30 Nm).
      2. M11 bolts 2nd pass: in sequence + 90 degrees.
      3. M11 bolts (1,2,3,4,5,6,7,8): + 90 degrees.
      4. M11 bolts (9 and 10): + 50 degrees.
      5. M8 cylinder head bolts (11,12,13,14,15) to 22 ft. lbs. (30 Nm). Begin with the center bolt (11) and alternating side-to-side, work outward tightening all of the bolts.
    2. Tighten the second design cylinder head bolts as follows:
      1. M11 bolts (1-10) 1st pass: in sequence to 22 ft. lbs. (30 Nm).
      2. M11 bolts (1-10) 2nd pass: in sequence + 90 degrees.
      3. M11 bolts (1-10): + 70 degrees.
      4. M8 cylinder head bolts (11,12,13,14,15) to 22 ft. lbs. (30 Nm). Begin with the center bolt (11) and alternating side-to-side, work outward tightening all of the bolts.

    c409909.jpg

    Fig. Cylinder head bolt tightening sequence-4.8L, 5.3L and 6.0L engines (click for zoom)


    Install the cylinder head bolts in sequence to 22 ft. lbs. (30 Nm). The bolts must be tightened once, then be tightened again in sequence in the following order:
    1. Step 1: Short length bolt: (3, 4, 7, 8, 11, 12, 15, 16), plus 55 degrees.
    2. Step 2: Medium length bolt: (14, 17), plus 65 degrees.
    3. Step 3: Long length bolts: (1, 2, 5, 6, 9, 10, 13), plus 75 degrees.

    7f05cb7.jpg

    Fig. Cylinder head bolt tightening sequence-5.0L and 5.7L engines

    Aug 04, 2010 | 1999 GMC Yukon Denali

    1 Answer

    What is the torque for head screws and timing


    300M, Concorde, Intrepid, LHS, 1998-2004 - Cylinder Head
    Removal & Installation
    2.7L Engines
    1. Before servicing the vehicle, refer to the Precautions section.
    2. Properly relieve the fuel system pressure.
    3. Drain the cooling system.
    4. Remove or disconnect the following:
      NOTE Place shop rags in the openings to prevent debris from entering the engine.
      Negative battery cable Accessory drive belts Crankshaft damper Intake plenum, lower intake manifold and exhaust manifold Valve and timing chain covers Coolant connections for the cylinder heads
    5. Rotate the crankshaft until the crankshaft timing mark aligns with the timing mark on the oil pump.
      WARNING Be sure the head bolts 9-11 are removed before attempting to remove the cylinder head, the head and/or block may be damaged.
      Primary timing chain Camshaft bearing caps, gradually, in the reverse order of the tightening sequence Camshafts Cylinder head bolts in reverse order of installation starting with bolts 11-9, then 8-1 Cylinder head(s)

    To install:


    af080a0.jpg

    Fig. Camshaft bolt tightening sequence-2.7L engine

    eb0ed0f.jpg

    Fig. Cylinder head bolt tightening sequence-2.7L engine
    1. Thoroughly clean and dry the mating surfaces of the head and block. Check the cylinder head for cracks, damage or engine coolant leakage. Remove scale, sealing compound and carbon. Clean the oil passages thoroughly.
    2. Place a new head gasket on the cylinder block over the locating dowels.
    3. Inspect the cylinder head bolts for necking (stretching) by holding a straightedge against the threads of each bolt. If all of the threads are not contacting the straightedge, the bolt should be replaced. New head bolts are recommended.
      WARNING Due to the cylinder head bolt torque method used, it is imperative that the bolt threads be inspected for necking (stretching) prior to installation. If the threads are necked down, the bolt should be replaced. Failure to do so may result in parts failure or damage.
    4. Lubricate the bolt threads with clean engine oil, then install them.
    5. Torque the head bolts in the sequence shown in the illustration, utilizing the following steps and tightening values:
      1. Step 1: bolts 1 through 8: 35 ft. lbs. (48 Nm).
      2. Step 2: bolts 1 through 8: 55 ft. lbs. (75 Nm).
      3. Step 3: bolts 1 through 8: 55 ft. lbs. (75 Nm).
      4. Step 4: bolts 1 through 8: plus 90 degree turn using a torque angle meter.
      5. Step 5: bolts 9 through 11: 21 ft. lbs. (28 Nm).

    6. Install or connect the following:
      Camshafts, timing chain and sprockets Water connections to the cylinder head Valve and timing chain covers Crankshaft damper and torque the center bolt to 125 ft. lbs. (170 Nm) Lower intake manifold and intake plenum Exhaust manifolds Accessory drive belts Negative battery cable
    7. Fill the cooling system to the proper level.
    8. Start the vehicle, check for leaks and repair if necessary.
    continue...

    Apr 11, 2010 | 2002 Dodge Intrepid

    1 Answer

    I am looking for the cylinder head torque specification for the 3.3litre chrysler town and country 2003


    Tighten the cylinder head bolts 1 - 8 in the sequence shown in Cylinder Head Bolts Location and Tightening Sequence Using the 4 step torque turn method, tighten according to the following values:
    Step 1: Bolts 1 - 8 to 61 N·m (45 ft. lbs.)
    Step 2: Bolts 1 - 8 to 88 N·m (65 ft. lbs.)
    Step 3: Bolts 1 - 8 (again) to 88 N·m (65 ft. lbs.)
    Step 4: Bolts 1 - 8 turn an additional 1/4 Turn. (Do not use a torque wrench for this step.)
    NOTE: Bolt torque after 1/4 turn should be over 122 N·m (90 ft. lbs.) If not, replace the bolt.

    Tighten head bolt number 9 Cylinder Head Bolts Location and Tightening Sequence to 33 N·m (25 ft. lbs.) after head bolts 1 - 8 have been tighten to specifications.

    Jan 24, 2010 | 2003 Chrysler Town & Country

    1 Answer

    What is the cylinder head torque spec for a 2005 nissan sentra 1.8 liter engine


    1. For 1.8L engines, tighten the bolts in sequence, as follows:
      1. Step 1: Bolts 1-10 to 22 ft. lbs. (29 Nm).
      2. Step 2: Bolts 1-10 to 43 ft. lbs. (59 Nm).
      3. Step 3: Loosen bolts 1-10 completely.
      4. Step 4: Bolts 1-10 to 22 ft. lbs. (29 Nm).
      5. Step 5: Bolts 1-10 plus 50-55 degrees.
      6. Step 5: Bolts 11-14 to 74 inch lbs. (8 Nm).

        0900c152801afb79.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Cylinder head torque sequence-1.8L engine


        0900c152801afad8.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Tighten the valve cover bolts in sequence-1.6L and 1.8L engines

    Nov 13, 2009 | 2005 Nissan Sentra

    2 Answers

    What is the tension on cylinder head bolts for a jeep grand cherokee 307935 4 litre, 6 cylinder, 1999, petrol motor.


    Coat threads of left hand front bolt with sealant: 1st - step; - 22 ft./lbs. 2nd - step; - 45 ft./lbs. 3rd - step, all bolts except L.H. front bolt; - 110 ft./lbs. 4th - step, L.H. front bolt; - 100 ft./lbs. fig100.png

    Sep 05, 2009 | 1999 Jeep Grand Cherokee

    1 Answer

    Need to know cylinder head bolt torque specs


    Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

    Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

    Not finding what you are looking for?
    1995 Volkswagen Polo 1.4 Logo

    Related Topics:

    783 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Volkswagen Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    yadayada
    yadayada

    Level 3 Expert

    76132 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8273 Answers

    Are you a Volkswagen Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...