Question about Cars & Trucks

Open Question

1997 ford explorer ignition control module - Cars & Trucks

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
chuck943
  • 783 Answers

SOURCE: where is the ignition module control located on 1996 ranger 2.3 e

It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Posted on Apr 08, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have ford escort 1.4i year 1997 I have change crank senson and ignition coil and can sensor and ignition control module but don't want to spark what is the problem what else I have to check


This vehicle doesn't have ignition control module ! The PCM - engine computer controls the coils . Also 1997 escort came with a 2.0 L engine . Not 1.4 . Testing an not guessing is the way to a proper fix. Your best bet , take it to a qualified repair shop .

Apr 21, 2017 | Ford Cars & Trucks

1 Answer

Needing to find location of TCM on 1997 ford explorer 4x4


The 1997 Ford explorer does not have separate Transmission Control Module, the transmission is controlled by PCM

Apr 20, 2013 | 1997 Ford Explorer AWD

1 Answer

1996 FORD EXPLORER , MISS FIRE ON CYL # 2, 1ST REPLACED PLUGS AND WIRES, THEN THE COIL PACK AND LAST THE FUEL INJECTOR BUT PROBLEM STILL THERE, ANY HELP WOULD BE GREAT


OK,
Have you tried the following:


Ignition Control Module (ICM) REMOVAL & INSTALLATION NOTE: Only the EEC-IV ignition systems use an external ICM. EEC-V systems have incorperated the ICM into the Power Control Module (PCM).
  1. Disconnect the negative battery cable.
  2. Detach the wiring harness connector(s) from the ICM.
  3. Remove the mounting bolts, then remove the ICM. To install:
  4. Position the ICM onto the inner fender apron and install the mounting bolts. Tighten the bolts to 22–31 inch lbs (2.5–3.5 Nm).
  5. Attach the wiring harness connector(s) to the ICM.
  6. Connect the negative battery cable. Fig. 1: Ignition control module and mounting location on the 2.3L, 2.5L engine 89682g32.gif
    Fig. 2: Ignition control module used on all EEC-IV systems except the 2.3L engine 89682g33.gif
    Fig. 3: Ignition control module mounting on all EEC-IV systems except the 2.3L engine 89682g34.gif
prev.gif next.gif

Jul 11, 2010 | 1996 Ford Explorer

1 Answer

Need help finding the ignition module on a 97 ford crown victoria


There is no ignition module. The ignition coils are controlled directly by the Powertrain control module (computer) located inside the vehicle above the drivers left foot and connected to the engine wiring harness thru the firewall

Apr 06, 2010 | 1997 Ford Crown Victoria

1 Answer

I have a 1997 Ford Explorer that will turn over but will not start. I reset the fuel pump switch, but that did't help, any suggestions.


ignition problems start with a new cranksensor if it has tbs or multiport ... if it has a distribitor change the pickup coil or ingition control module

Mar 01, 2010 | 1997 Ford Explorer AWD

1 Answer

1997 explorer a/c blend door ?


may possibly have a vacuum leak.

May 31, 2009 | 1997 Ford Explorer AWD

1 Answer

Replacing the control module on my 1997 ford explorer


the module is located behind the dash just to the left of the radio. remove the two screws below the radio and the dash panel snaps out and you can access the module

May 10, 2009 | 1997 Ford Explorer AWD

3 Answers

Where is the ignition module control located on 1996 ranger 2.3 e


It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Apr 08, 2009 | 1996 Ford Ranger SuperCab

2 Answers

Ignition control module location for 1997 ford thunderbird?


1997 Ford Thunderbird Transmission problem
When driving normally transmission surges like it is not in gear. Had sensors replaced, nitural safety switch, and still acts up.

Dec 12, 2008 | 1997 Ford Thunderbird LX

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...