Question about 1993 Toyota Corolla

Open Question

Howto bleed Clutch hydraulic in a toyota corolla 1998

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 14 Answers

SOURCE: How do you rplace an ignition lock cylinder on a 98 toyota corolla

You can do this one yourself if you want it does not require removing the steering wheel. just the plastic housing from the steering column.
remove housing/cover. then look at housing with cylinder lock assem. on bottom about 1.2 inches or so from the end of the lock assembly you will see a very small hole insert metal pin into hole and push in while turning the key in the ignition backwards to accessory positionyou will feel the pin your pushing move in a bit, then you should be able to pull the cylinder assembly out. insert new assembly with key in the same position and turn forward this will install your new assemlby then reassemble your plastic column covers.

Posted on May 26, 2009

Ad
  • 9 Answers

SOURCE: wondering if a 1998 toyota corolla will fit in a 2000 corolla

In 1998 the 1zz-fe engine was intoduced. Toyota only added variable valve timing in the 2000-2002 1zz Corolla engines. Same engine same parts and components

Computers should not need swapped but you could go to the dealer and ask for the part number for 1998-2002 ECU's for Corolla. This is the electronic control modul on the car that runs the engines.It is usually located under the dash by the passengers side glove box.

Posted on May 27, 2009

scottyoung56
  • 89 Answers

SOURCE: toyota corolla 1.4 vvti cluth problem

try to give it a little gas when letting the clutch out

Posted on Jul 03, 2009

alicantecoli
  • 22219 Answers

SOURCE: Toyota corolla 1300 1998 model - How many km does

80000miles or 6years

Posted on Jan 21, 2010

  • 137 Answers

SOURCE: I need to replace the

Pay someone. This is a difficult job that should take a trained technician in a well equipped shop 5-6 hours to complete. That does not include having the flywheel resurfaced. Unless you are very organized, have adequate tools, torque specs, knowledge of what parts to replace and inspect while in there, and what not to destroy when removing the transmission and what to replace when putting it back together, you might get in over your head rather quickly. I am not out to doubt anyone's ability but this is not a as simple as an oil change or a brake job that even a novice can perform in a driveway unless you are 100% positive you are up to the task of removing the transmission, properly replacing the clutch and reinstalling the transmission I advise you not to open that can of worms until you are better trained. There are a ton of snags that you can and will run into during this job and you will need to know what to do. You can't get everything from a manual or how-to book.
Good luck.

Posted on Oct 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Does Toyota hilux R150 gear box have a clutch adjustment ?ie master cylinder adjustment ?


If it is adjustable it will have a threaded push rod at the slave cyl ,bleed the hydraulic system first adult the clutch then bleed again .

Oct 26, 2015 | Toyota Cars & Trucks

1 Answer

What type of clutch fluid to use in a 1998 toyota corolla


Practically applied for more than 4 decades I have found that the clutch fluid is not more than a brake fluid. This Brake fluid is broken as
DOT(s) and ranges 2 to 5. Properties are of higher numbers say like DOT 3 and 4 have more ability to resist heat and have higher boiling temperature marks than DOT 2. Cars like manufactured around 1998 should use Dextron II D or 3. If you are to top up the level (you can check the minium and maxium level marks at the outside of the fluid plastic reservoir) the best is to top up to maximum level with as same as mother fluid. If you can't get or don't know what brand or what type of clutch fluid is already exits and not to get even a small reactions between fluids, flush out the existing one and replaced with the other.
Make sure you have enough amount of fluid for your dry clutch hydraulic system. One 0.5 bottle is good enough for family and light trucks. Make sure you bleed out all the air trapped inside the dydraulic system. Good luck.

Jun 24, 2014 | 2005 Toyota Corolla

1 Answer

I have a Toyota corolla 2004,I started my car, but I can't get the car into gear. And now I shut it down, but when I tried to start it up, it won't start now, not even in nuetrol.


I thinking that you have either a hydraulic clutch or a cable operated clutch. If hydraulic then bleed out the system and see if the clutch works .If not replace the clutch master cylinder and slave cylinder . If cable then replace the cable. Some cars require it to be in neutral with the foot on the clutch before the starter will work (Safety reasons) so if the clutch is not working then nothing will work

Nov 15, 2013 | Cars & Trucks

1 Answer

Where is the transmission cable located on 1998 corolla


Clutch cable? Actually, I think you'd have a hydraulic clutch. If it's cable, it would come out of the firewall, where your clutch pedal operates, and down to the transmission. If it's hydraulic, there'd be a clutch reservoir just beside your brake reservoir on the firewall, with a hose leading down to a "clutch slave cylinder" mounted on your transmission. If you have no clutch, this slave cylinder can be easily bled of air and will gravity feed new fluid to the cylinder.

Oct 25, 2011 | 1998 Toyota Corolla

1 Answer

Clutch pedal has no resistance like it's not even working. is it the clutch itself or the pedal.


It appears to be a hydraulic clutch so your reservoir is probably empty and there is no fluid to operate the clutch. Try filling the reservoir and bleeding the clutch. If that does not work you will have to overhaul or replace the master cylinder or the slave cylinder. None of the above are really difficult tasks.

Feb 27, 2011 | 1993 Toyota Corolla

1 Answer

My clutch is not angaging need to see how can i bleed


Hydraulic Clutch System BLEEDING The clutch system can be bled using a pressure bleeder. Follow the instructions that come with the pressure bleeder for the proper pressure bleeding procedure. The maximum line pressure while pressure bleeding must not exceed 36 psi (248 kPa). NOTE: To bleed a clutch manually requires the assistance of a second person, a section of hose that is compatible with brake fluid (preferably clear) and fits the slave cylinder bleed screw snugly and a container to catch the fluid that is bled through the system. As brake hydraulic fluid easily absorbs moisture, always use fresh fluid when bleeding a hydraulic system.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. To bleed the system perform the following:
    1. Top off the hydraulic fluid reservoir using a fluid that meets the standards of the vehicle's hydraulic system.
    2. Open the clutch slave cylinder bleed screw and press the clutch pedal to the floor and hold the pedal down.
    3. Close the clutch slave cylinder bleed screw.
    4. Release the clutch pedal.
    5. Check the hydraulic fluid level and top off as necessary.
  3. Repeat the above steps until the discharged fluid is clean and no air bubbles appear during the bleeding process.
prev.gif next.gif

Aug 03, 2010 | 1998 Audi A4

1 Answer

1998 corolla needs clutch adjustment or replacement. It grinds some & is difficult to get in gear often.Brian


I had a hydraulic clutch on a nissan that was low on fluid and it had the same problem.

May 08, 2009 | 1998 Toyota Corolla

1 Answer

Clutch adjustment for toyota corolla 1984


the clutch is hydraulic and self adjusting, if it is slipping then it is time for a clutch, the sign of a worn clutch is the clutch engages when the pedal is near the top of its travel when u let it out

Apr 12, 2009 | 1984 Toyota Corolla

1 Answer

Hydraulic Clutch Problem in an 82 Toyota Pickup


If you are leaking fluid from the clutch master cylinder then you have air in the system. You could try and bleed the air out of the clutch slave cylinder to get the gears but it would not last. The only way is to replace the defective master cylinder, replace all of the fluid and bleed out the air through the slave cylinder.

Apr 07, 2009 | 1985 Toyota Corolla 2 Door

2 Answers

Trying to figure out how to adjust the clutch on a 2005 Toyota Corolla style s


You car does not have an "adjustable" clutch. The Corolla uses a hydraulic clutch. The action of the hydraulics eliminates the need for adjustements. If the clutch is slipping, you may need to replace the clutch.

Jan 15, 2009 | 2005 Toyota Corolla

Not finding what you are looking for?
1993 Toyota Corolla Logo

Related Topics:

177 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...