Question about Cars & Trucks

Open Question

Holden rodeo 1994 2.6 litre valve clearances

Valve clearances please

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: 1994 isuzu holden rodeo injection timing adjustment

try u-pull our patrs

Posted on Sep 12, 2008

Ad
snownbird33
  • 120 Answers

SOURCE: Holden 94 rodeo petrol

Good Day
Vale clearance cold
intake .006 in (.15 mm)
exhaust .010 in (.25 mm)

Timing
1. With transmission in Neutral or park, start engine and warm to normal operating temp. turn eng,and all accessories off. connect Tachometer. Connect timing light to no 1 spark plug wire.

2. Disconnect and plug fuel vapor canister purge hose and EGR vacuum hose. Start and ensure idle is 900 RPM. adjust idle as required. Check ignition timing ( 12 @ 900)

3. If adjustment is required, loosen distributor hold down bolt and turn until timing is within specification. Tighten distributor hold down bolt and recheck timing. adjust idle speed as required.

hope this helps

Cheers

Posted on Sep 30, 2008

dttech
  • 4803 Answers

SOURCE: i want to set valve

Knowing Intake from Exhaust is pretty basic...The intake valves are on the intake side of the head and the Exhaust valves are on the Exhaust side. If you don't know the difference between an exhaust valve and an intake valve, how are you going to know if your cams are lined up properly so you can check the clearance on each valve? How are you going to know if the cylinder you are checking is on Top Dead Center?

Posted on Apr 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hey there I need the exhaust and Intake(valve) clearance for a komatsu 300-6 please


note Perform the valve clearance check and adjustment at the engine cold state. 1.Remove all of the ignition coils. 2.Remove the cylinder head cover.
caution Turn the crankshaft always clockwise. 3.Turn the crankshaft clockwise, and align the timing mark on the exhaust camshaft sprocket against the upper face of the cylinder head as shown in Figure. Therefore, No.1 cylinder goes to the compression top dead center. 4.Using a thickness gauge, measure the valve clearance with the arrow shown in Figure. If deviated from the standard value, make note for the valve clearance.
Standard value:

    Intake valve 0.20 ± 0.03 mm (0.008 ± 0.0012 inch)
    Exhaust valve 0.30 ± 0.03 mm (0.012 ± 0.0012 inch)
5.Turn the crankshaft clockwise 360 degrees, and put the timing mark on the exhaust camshaft sprocket in position shown in Figure. Therefore, No. 4 cylinder goes to the compression top dead center. 6.Check the valve clearance with the arrow shown in Figure. In the same procedure as 4.
7.If the valve clearance is deviated from the standard value, remove the camshaft and the valve tappet. For the camshaft removal, refer to Camshaft Removal and Installation . 8.Using a micrometer, measure the thickness of the removed valve tappet. 9.Calculate the thickness of the newly installed valve tappet through the following equation.
A: thickness of newly installed valve tappet
B: thickness of removed valve tappet
C: measured valve clearance
Equation

    Intake valve: A = B + [C - 0.20 mm (0.008 inch)]
    Exhaust valve: A = B + [C - 0.30 mm (0.012 inch)] note The valve tappet ranges 3,000 - 3,690 mm (0.1181 - 0.1453 inch) and has 47 types per 0.015 mm (0.0006 inch). The thickness below a decimal point is stamped on the reverse side of the valve tappet. 10.Install the valve tappet selected through the procedure 9, and put the camshaft in position. For the camshaft installation, refer to Camshaft Removal and Installation .
    11.After installing the timing chain, measure the valve clearance using the procedure 3 to 6. Confirm the clearance is within the standard value.
    caution Completely remove all the old FIPG, which might be remaining among the components. 12.After completely removing the liquid gasket adhering on the timing chain case, cylinder block and cylinder head, degrease them with white gasoline.
    caution The cylinder head cover should be installed within 3 minutes of applying liquid gasket.
13.Apply a 4 mm bead of liquid gasket as illustrated.
Specified sealant:
    THREE BOND 1217G or equivalent
14. Install the cylinder head cover and tighten the tightening bolts using the following procedures.
(1) Temporarily tighten to the following torque in order shown in the illustration.
Tightening torque: 3.0 ± 1.0 N·m (27 ± 8 in-lb)(2) Tighten to the specified torque in order shown in the illustration.
Specified torque: 5.5 ± 0.5 N·m (49 ± 4 in-lb)15.Install the ignition coils.

Jan 23, 2017 | Cars & Trucks

1 Answer

What is the valve clearance of nissan caravan


Valve lash is the end of the rocker arm and the valve stem clearance between. When the engine is running, due to the thermal expansion and contraction, if there is no gap between the rocker arm and the valve stem, rocker arm swells, the top valve open, the impact of engine power and economy. Engine valve clearance will be different, usually when the car is cold, the intake valve 0.08-0.10MM, clearance exhaust valves 0.10-0.12MM Car Diagnostic Tool

Aug 26, 2016 | Nissan Cars & Trucks

1 Answer

Valve clearance


Valve clearance Google search your year make and model valve clearance. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Checking and adjusting valves
Engine Valve Adjustment Procedure The Right Way
Valve Clearance Adjustment
Valve clearance Google Search

Aug 10, 2016 | Cars & Trucks

1 Answer

What is the valve clearance for intake valve and exhaust valve for mitsubishi engine 4D32?


Please follow link to complete instuction's on the Correct way to set valve clearance on the 4D32 engine type.
6 INTAKE AND EXHAUST VALVE CLEARANCE INSPECT AND ADJUST

May 15, 2016 | Mitsubishi Cars & Trucks

2 Answers

Valve clearance 4hj1 isuzu


Intake valves clearance cold 0.4mm(.016inches)
Exhaust valve clearance cold 0.4mm(.016inches)

Oct 28, 2015 | 2001 Isuzu Rodeo

1 Answer

What is the valve clearance on a 2007 Holden Rodeo 2.4L Petrol?


They don't have adjustable value they are hydrolic

Sep 18, 2014 | Holden Ute Cars & Trucks

2 Answers

Please assist with Cylinder Head Torque and Valve Clearance Specs for Tata Indica 1.4 LXi


i need the head talk settings & valve clearance for tata indica lxi

Apr 20, 2013 | 2006 Tata Indica LXi

2 Answers

I want to set valve clearances on 1997 2.6 petrol holden rodeo. i need valve sequence? how can i tell which is exhast and which is intake?


the valve clearance is intake .006 exhust .010 they must be set with engine cold passenger side is the intake driver side is the exhust send me your e-mail and i will send you the procedure.

Apr 08, 2011 | Isuzu Rodeo Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...