Question about 2001 Jeep Grand Cherokee

1 Answer

How can i program my garage door to open from my 01 jeep grand ch

I want to program my automatic garage door control into my 01 jeep grand cherokee, how can i do that?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Hold down the button on your garage door opener while pushing one of the 3 buttons on the overhead console in the Jeep. It will beep when confirmed.

Posted on Jan 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2012 grand cherokee fuel door release button doesn't work


Fuel door doesnt open - Jeep Garage - Jeep Forum

www.jeepgarage.org > ... > Trouble Shooting/Problems/Service

May 20, 2011 - 12 posts - ‎3 authors
try pressing the button and have someone else try to open the door, if it works, ... i tried that and it didnt work ... I have a 2011 Grand Cherokee Limited and my problem is that the fuel door stuck or ... There is a manual release in the cargo area. .... Itdoesn't sound like the internet is going to solve your issue.

2012 Grand Cherokee fuel door release button doesn't work? ' Yahoo ...

https://answers.yahoo.com/question/index?qid...

Dec 16, 2015 | 2012 Jeep Grand Cherokee

2 Answers

Keyless remote 1996 jeep grand cherokee laredo programing


Instructions
  1. Programming the First Transmitter
    • 1

      Unlock all of the Jeepicon1.png Grand Cherokee's doors and open the driver's side door. Keeping the door open, lock it using the manual lock on the door itself.

    • 2

      Put the manual key into the ignition and switch it to the "On" or "Run" position, whichever applicable, without starting the engine.

    • Sponsored Links

    • 3

      Point the remote at the receiver (located by the little bulb on the caricon1.png ceiling) and hold down the "Lock" button for up to 5 seconds.

    • 4

      When the driver's side door unlocks, you know the remote has been programmed correctly. If you are only programming one remote, jump to the next step. If not, manually re-lock the driver's side door and repeat steps 5 and 6 using each remote you would like to program and then continue.

    • 5

      Turn the key to the "Off" position and turn the ignition on immediately. This must be done within 20 seconds of programming the last remote. You're finished!

Sponsored Links

Read more: How to Program the Remote on a 1996 Jeep Grand Cherokee ' eHow.com http://www.ehow.com/how_7433787_program-1996-jeep-grand-cherokee.html#ixzz2KdCc5PQq

Feb 11, 2013 | 1996 Jeep Grand Cherokee

1 Answer

How do you "train" the


Instructions
    • 1 Turn off the engine of the car and press and hold buttons 1 and 3 on the Jeep's transmitter for 20 seconds to erase previous codes. Release them when the display reads "Channels Cleared."
    • 2 Hold your garage-door remote 1 to 3 inches from the Jeep transmitter.
    • 3 Press and hold the open button on your handheld remote and simultaneously press the button you wish to program on the Jeep's transmitter. For example, if you want button 2 to be the one you use to open your garage door, press button 2 while pressing the open button the remote.
    • 4 Release the button once you hear a beep and the display reads "Trained."
    • 5 Press the "smart" button on your garage door motor. This button is usually located on the back or side of the motor near the antenna wire and light lens.
    • 6 Return to your vehicle and press and hold the programmed button in your Jeep for 2 seconds. Release and press and hold the button for another 2 seconds to complete the programming sequence. You will now be able to use the vehicle's transmitter to open your garage door.

Sep 14, 2011 | 2001 Jeep Grand Cherokee

1 Answer

I want to program the garage door opener for a 1998 Jeep Grand Cherokee that we just bought. How do I do that?


Depends which kind of garage opener you have. But generally, it goes like this:

In car, press and hold 2 outer buttons on overhead console until indicator lights start flashing.

Hold desired button you want to program garage opener with until lights begin to flash rapidly.

At the garage door receiver in the garage, press the "learn" button. (Mine was located under one of the plastic light covers; it is purple in mine, can be other colors, but should say "learn button" or something similar) If I recall correctly, the light next to the learn button started flashing after I pressed it.

Quickly go back to the car, and press and hold the desired button and the garage should close.

That should be it.

Jul 26, 2011 | 1998 Jeep Grand Cherokee

1 Answer

2002 Grand Cherokee: i need help programing my garage door opener...


The process is simple but too lengthy to post here.


Goto homelink.com


They make the system and have very complete instructions you can download.


PLEASE NOTE: MOST but not ALL Brands / models of opener will work with this system.

May 18, 2010 | 2002 Jeep Grand Cherokee

1 Answer

I got a U0103 and P0700 error code on my 2006 Jeep Grand Cherokee. Do I need to do anything about it?


I DID NOT SEE CODE UO103 BUT CODE PO700 IS AUTOMATIC TRANSMISSION CONTROL SYSTEM MALFUNCTION.WHAT CODE IS TELLING YOU THAT YOU HAVE A FAULTY TRANSMISSION CONTROL MODULE.THATS A GARAGE FIX BECAUSE THEY HAVE TO REPROGRAM IT BEFORE YOUR JEEP WILL SHIFT RIGHT.

Apr 20, 2010 | 2006 Jeep Grand Cherokee

1 Answer

How to I program my garage door opener in my 1994 jeep grand cherokee?


GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

Jan 03, 2010 | 1994 Jeep Grand Cherokee

1 Answer

01 jeep grand cherokee limit driver side air warm


You have the blend doors problem which needs to be fixed. At jeep it is about £1300, by EDM in bicester it is £255 and maintains dual control. I would imagine the recirc dooe is or soon will go as well.

Oct 22, 2009 | 2001 Jeep Grand Cherokee

1 Answer

How to set-up visor remote with garage door remote


To program the car to your remote-hold down the 2 outer buttons until the red light blinks or comes on(not sure its been awhile) then put the garage door remote next to the sunvisor, hold down the button on the remote and any button on the sunvisor at the same time until the red light blinks. Thts it.

Mar 06, 2009 | 1996 Jeep Grand Cherokee

1 Answer

My garage door opener on my jeep


Go to dealer. Borrow a users manual. The procedure is easy. You need the handheld remote to synch the homelink to the door opener.

Dec 19, 2008 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
2001 Jeep Grand Cherokee Logo

944 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...