Question about 2004 Isuzu Axiom

Open Question

Where is map sensor location on 2004 Isuzu Axiom

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
alicantecoli
  • 22156 Answers

SOURCE: 1992 ISUZU TROOPER Crank Sensor location

doesnt have one its inside the distributor

Posted on Feb 04, 2009

Ad
  • 1 Answer

SOURCE: I need timing specs for 3.5 2002 Isuzu Axiom

I have found that one can mark (Paint pen) the gears and teeth (One tooth and one corresponding belt rib) on each gear prior to removing the belt. You can then overlay the old belt on a new belt and mark the same spots on the new belt and then install the belt so your marks on the gears and belt line up as they did before you removed the old belt. Given that your timing was right to start with....if done correctly, this will work.

Posted on May 09, 2009

  • 1 Answer

SOURCE: replace thermostat on isuzu axiom

I just had a garage replace my thermostat on my 2002 Isuzu Axiom. The book calls for 2 hrs labor, no way. iI took the garage more like 5 hrs plus, they ate the additional 3 hrs of labor. Note, the intake manifold must be removed and even then special tools are needed because it is still buried deep down. The garage took pictures ot this one because of how ridiculours Isuzu designed the location.

Posted on Aug 20, 2009

  • 75 Answers

SOURCE: where is the map sensor located on a 2004 rodeo

check the right side of the intake manifold or the right rear of the intake manifold...

Posted on Feb 03, 2010

  • 1 Answer

SOURCE: i have a 2004 Isuzu Axiom, my check engine light

You may have actually had a faulty MAP that needed replace. Thing is that any time you get a "check engine", the cruise will be disabled. you must clear the code, by either a trouble code diagnostic tool, or disconnect the battery for about five minutes. Codes will clear, and cruise will start working again.

Posted on Jan 24, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Goes do I get the rear wheel bearings off a 2003 Isuzu Axiom


quote
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:
    • Rear wheel
    • Disc brake caliper and bracket
    • Disc brake rotor
    • Wheel speed sensor bracket
    • Parking brake cable and bracket
    • Parking brake shoes
    • Axle shaft 4 and bearing housing 5
    • Snapring and discard it
    • Bearing, press it off the axle shaft with the bearing holder and oil seal. (you will need new seals)


26120462-bc3iup444wd3jyd1bmsomxey-2-0.jpg

Mar 06, 2016 | Isuzu Cars & Trucks

1 Answer

I have a 2004 Isuzu axiom my check enegine is on .I put new sensors on it ,but the light is still on.


Most people have the misconception that a trouble code tells you what part to replace. The fact is the code tells the mechanic only what to check.
The problem could be a sensor, or a wiring harness, or something mechanical.

Aug 05, 2013 | 2004 Isuzu Ascender

2 Answers

Where is the map sensor located on a 2004 isuzu rodeo 3.5l v6


check the right side of the intake manifold or the rear of the manifold

Mar 04, 2011 | 2004 Isuzu Rodeo

2 Answers

I have a 2004 Isuzu Axiom, my check engine light came on as i was on the interstate with my cruise control on. The cruise control stop working exactly the same time the engine light came on. I took it to...


You may have actually had a faulty MAP that needed replace. Thing is that any time you get a "check engine", the cruise will be disabled. you must clear the code, by either a trouble code diagnostic tool, or disconnect the battery for about five minutes. Codes will clear, and cruise will start working again.

Nov 19, 2010 | 2004 Isuzu Axiom

1 Answer

We're is a bank 1 sensors located on a 2002 isuzu axiom.


BANK ONE SENSOR IS UP STREAM ITS ON EXHUST MANIFOLD OR EXHUST PIPE BEFORE CAT CONVERTOR

Oct 11, 2010 | 2002 Isuzu Axiom

2 Answers

Where is the map sensor located on a 2004 rodeo


check the right side of the intake manifold or the right rear of the intake manifold...

Feb 03, 2010 | 2004 Isuzu Rodeo

1 Answer

Check engine light on


Ckt is your Torque Converter. it could be something small as a seal. that code alone doesnt do any good, without visually inspecting the Torque converter. in anycase, its not a job i recommend doing at home. one thing can lead to another which leads to disaster. Take it into your local shop.

Aug 09, 2009 | 2004 Isuzu Axiom

4 Answers

Leaking transmission fluid


How can I check transmission fluid on a 2002 Axiom - dipstick!

Jul 21, 2008 | 2002 Isuzu Axiom

Not finding what you are looking for?
2004 Isuzu Axiom Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...