Question about 1999 Ford Escort

1 Answer

1994 escort 1.8d van fanbelt

The fixing bolt to the bottom adjustable bracket , the one with the castellated adjuster on it is worn and the belt cannot be tensioned enough to stop the belt slipping any suggestions?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 345 Answers

Put a hammer shaft behind the alternator and pull on the handle then tighten the bolt....

Posted on Jan 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the power steering belt on a 4g13



ADJUSTMENT

Excessive belt tension will cause damage to the alternator and water pump pulley bearings, while, on the other hand, loose belt tension will produce slip and premature wear on the belt. Therefore, be sure to adjust the belt tension to the proper level.
To adjust the tension on a drive belt, loosen the adjusting bolt or fixing bolt locknut on the alternator, alternator bracket or tension pulley. Then move the alternator or turn the adjusting bolt to adjust belt tension. Once the desired value is reached, secure the bolt or locknut and recheck tension.


REMOVAL & INSTALLATION

1.5L, 1.6L, 1.8L, 2.0L and 2.4L Engines


0900c15280037bf7.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory V-belt routing-Mitsubishi 1.5L, 1.6L, 1.8L, 2.0L and 2.4L engines
Alternator Belt


0900c15280037bf8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Loosen the adjuster lock bolt . . .


0900c15280037bf9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. . . . then remove the alternator belt from the engine

  1. Loosen the alternator support nut.
  2. Loosen the adjuster lock bolt.
  3. Rotate the adjuster bolt counter clockwise to release the tension on the belt.
  4. Remove the belt.

To install:
  1. Install the belt on the pulleys.
  2. Rotate the adjuster bolt clockwise until the proper tension is reached.
  3. Tighten the adjuster lock bolt and the alternator support nut.

POWER STEERING BELT


0900c15280037bfa.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. After the adjusting and fixed bolts are loosened, rotate the pump . . .


0900c15280037bfb.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. . . . then remove the power steering belt from the engine

  1. Remove the alternator belt as described above.
  2. Loosen the power steering pump adjusting bolts.
  3. Remove the power steering pump fixed bolt on the rear of the bracket.
  4. Rotate the pump toward the engine and remove the belt.

To install:
  1. Install the belt on the pulleys.
  2. Rotate the pump until the proper tension is reached.
  3. Tighten the adjusting bolts on the pump.
  4. Tighten the fixed bolt on the rear of the bracket.
  5. Install the alternator belt.

A/C COMPRESSOR BELT
  1. Loosen the tension pulley and remove the belt.
  2. The installation is the reverse of the removal.

3.0L DOHC, 3.0L SOHC Galant, and 3.5L Engines


0900c15280037bfc.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Serpentine belt routing-Mitsubishi 3.0L engines (except 1998-00 Galant models)


0900c15280037bfd.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory V-belt routing-Mitsubishi 3.5L and 1998-00 3.0L SOHC Galant engines
ALTERNATOR AND A/C COMPRESSOR

  1. Disconnect the negative battery cable.


CAUTION Wait at least 90 seconds after the negative battery cable is disconnected to prevent possible deployment of the air bag.
  1. Raise and safely support the vehicle and remove the front undercover.
  2. Loosen the tension pulley fixing nut and relieve the tension on the belt by turning the adjusting bolt.
  3. Remove the belt.

To install:
  1. Install the belt on the crankshaft and alternator pulleys.
  2. Using the adjusting bolt on the tensioner, tighten the belt to the desired tension.
  3. Tighten the fixing nut to hold the adjustment.
  4. Install the undercover and lower the vehicle to the floor.
  5. Connect the negative battery cable.

POWER STEERING BELT
  1. Disconnect the negative battery cable.


CAUTION Wait at least 90 seconds after the negative battery cable is disconnected to prevent possible deployment of the air bag.
  1. Raise and safely support the vehicle and remove the undercover.
  2. Remove the alternator and A/C compressor belt.
  3. Lower the vehicle and remove the cruise control pump link assembly.
  4. Place the power steering hose under the oil reservoir.
  5. Loosen the tension pulley fixing bolts and remove the power steering pump drive belt.

To install:
  1. Install the power steering pump drive belt.
  2. Insert an extension bar or equivalent into the opening at the end of the tension pulley bracket and pivot the pulley to apply tension to the belt.
  3. Tighten the fixing bolts.
  4. Raise the vehicle and install the alternator and A/C compressor belt.
  5. Install the undercover and lower the vehicle.
  6. Connect the negative battery cable.

3.0L SOHC Diamante
  1. Disconnect the negative battery cable.
  2. Loosen the lockbolt on the face of the A/C tensioner pulley.
  3. Turn the adjusting bolt of the A/C tensioner pulley to loosen the tension of the A/C belt.
  4. Remove the A/C compressor belt.
  5. Loosen the locknut on the face of the power steering/alternator tensioner pulley.
  6. Turn the adjusting bolt of the tensioner pulley to loosen the tension of the belt.
  7. Remove the power steering/alternator belt.

To install:
  1. Install the power steering/alternator belt first and then the A/C compressor drive belt.
  2. Adjust the belts to the proper tension by turning the adjusting bolts and tighten pulley fixing nut/bolt.
  3. Tighten the mounting nut of the power steering/alternator tensioner pulley to 36 ft. lbs. (50 Nm).

Mar 21, 2013 | 1996 Mitsubishi Mirage

1 Answer

Hi,how do u tighten the fanbelts in 1995 delica 2lt disel turbo van


YOU HAVE IDLER PULLEY WITHOUT ADJUSTING BOLT.TO TIGHTEN DRIVE BELTS YOU SWIVEL THE IDLER PULLEY WITH A PAIR OF PLIERS OR WRENCH ON THE BEARING MOUNTING UNTIL THE PROPER TENSION IS ACHIEVED.

May 16, 2011 | Mitsubishi Minivan Cars & Trucks

1 Answer

Changing alternator



REMOVAL & INSTALLATION 2.2L Engines
CHRYSLER ALTERNATOR

  1. Disconnect the negative battery cable.
  2. Label and disconnect the wiring (for easy installation).
  3. Remove the air conditioning compressor drive belt, if equipped.
  4. Loosen the alternator adjusting bracket bolt and adjusting bolt. Remove the alternator belt.
  5. Remove the bracket and mounting bolts.
  6. Remove the pivot bolt and nut.
  7. Lift the alternator from the vehicle.

When lifting the alternator out of the vehicle on some years with A/C, clearance may be restricted by the condenser cooling fan assembly or the A/C compressor and mounting bracket assembly, if so, removal of one of these items will be necessary.
To install:
  1. Position the alternator against the engine.
  2. Install the pivot bolt and nut.
  3. Install the mounting bracket bolts, and adjusting bolt.
  4. Install drive belts and adjust to specification.
  5. Tighten all the mounting bolts and nuts.
  6. Connect all alternator terminals.
  7. Connect the negative battery cable.

BOSCH ALTERNATOR
  1. Disconnect the negative battery cable.
  2. Disconnect the wiring and label for easy installation.
  3. Remove the air conditioning compressor drive belt.
  4. Loosen the alternator adjusting bracket locknut and adjusting screw. Remove the alternator belt.
  5. Remove the bracket locknut and mounting bolt.
  6. Remove the pivot bolt and nut.
  7. Remove the alternator from the engine.

To install:
  1. Position the alternator against the engine.
  2. Install pivot bolt and nut.
  3. Set the mounting bracket in place and install the bracket mounting bolt and locknut.
  4. Install the drive belts and adjust to specification.
  5. Tighten all the mounting bolts and nuts.
  6. Connect all alternator terminals.
  7. Connect the negative battery cable.

Jan 02, 2011 | 1994 Plymouth Voyager

1 Answer

How do you replace the alternator?


there are 2 locking bolts underneath and 2 bolts on the front belt adjuster bracket,undo the 2 bottom bolts and the bolt in the alt/bracket,loosen the block bolt/adjuster bracket,that will release the belt tension,then pull out of the engine bay,replacement is the 2 bottom bolts finger tight then the belt over the pulley then finger tight for the bracket,tension the belt be levering the alt away from the block and tighten up the alt/bracket first then the other 3.check belt tightness (1/2"movement/slack on longest run)then recheck all bolts tight.....you will need to recode your radio after.and dont forget to note what wires came off what terminals.......draw a picture if needed...

Jun 24, 2010 | 2004 Volkswagen Jetta

1 Answer

Changing alternator


REMOVAL & INSTALLATION
2.2L Engines
CHRYSLER ALTERNATOR
  1. Disconnect the negative battery cable.
  2. Label and disconnect the wiring (for easy installation).
  3. Remove the air conditioning compressor drive belt, if equipped.
  4. Loosen the alternator adjusting bracket bolt and adjusting bolt. Remove the alternator belt.
  5. Remove the bracket and mounting bolts.
  6. Remove the pivot bolt and nut.
  7. Lift the alternator from the vehicle.
When lifting the alternator out of the vehicle on some years with A/C, clearance may be restricted by the condenser cooling fan assembly or the A/C compressor and mounting bracket assembly, if so, removal of one of these items will be necessary.

To install:

  1. Position the alternator against the engine.
  2. Install the pivot bolt and nut.
  3. Install the mounting bracket bolts, and adjusting bolt.
  4. Install drive belts and adjust to specification.
  5. Tighten all the mounting bolts and nuts.
  6. Connect all alternator terminals.
  7. Connect the negative battery cable.

BOSCH ALTERNATOR

  1. Disconnect the negative battery cable.
  2. Disconnect the wiring and label for easy installation.
  3. Remove the air conditioning compressor drive belt.
  4. Loosen the alternator adjusting bracket locknut and adjusting screw. Remove the alternator belt.
  5. Remove the bracket locknut and mounting bolt.
  6. Remove the pivot bolt and nut.
  7. Remove the alternator from the engine.
To install:
  1. Position the alternator against the engine.
  2. Install pivot bolt and nut.
  3. Set the mounting bracket in place and install the bracket mounting bolt and locknut.
  4. Install the drive belts and adjust to specification.
  5. Tighten all the mounting bolts and nuts.
  6. Connect all alternator terminals.
  7. Connect the negative battery cable.

2.5L Engines
2.5L engines were equipped with either Chrysler or Bosch alternators.

  1. Disconnect the negative battery cable.
  2. Remove the drive belts.
  3. Remove the adjusting bracket-to-engine mounting bolt.
  4. Remove the adjusting locking bolt and nut, then remove the mounting bracket.
  5. Position the alternator to gain access to the wiring.
  6. Disconnect the wiring and label for easy installation.
  7. Remove the pivot bolt, nut, and washers.
  8. Remove the alternator assembly from the engine.
To install:
  1. Position the alternator assembly against the engine.
  2. Loosely install the pivot bolt, washers, and nut.
  3. Attach all wiring connectors to the alternator.
  4. Position the mounting bracket in place, then install engine mounting bolt.
  5. Loosely install the adjusting locking bolt and nut.
  6. Install the drive belts, and adjust to specification.
  7. Tighten all mounting bolts and nuts.
  8. Connect the negative battery cable.

2.6L Engines
2.6L engines were equipped with Mitsubishi alternators.
  1. Disconnect the negative battery cable.
  2. Disconnect the wiring and label for easy installation.
  3. Remove the adjusting strap mounting bolt.
  4. Remove the drive belts.
  5. Remove the support mounting bolt and nut.
  6. Remove the alternator assembly.
To install:
  1. Position the alternator assembly against the engine, then install the support bolt.
  2. Install the adjusting strap mounting bolt.
  3. Install the alternator belts and adjust to specification.
  4. Tighten all the support bolts and nuts.
  5. Connect all of the wiring terminals to the alternator.
  6. Connect the negative battery cable.

3.0L Engines
The 3.0L engines were equipped with either the Nippondenso or Bosch alternators.
  1. Disconnect the negative battery cable.
  2. Install a 1 / 2 in. breaker bar in the tensioner slot. Rotate counterclockwise to release belt tension and remove poly-V belt.
  3. Remove the alternator mounting bolts (2).
  4. Remove the wiring and remove alternator.
To install:
  1. Position the alternator onto the engine, then install the wiring.
  2. Set the alternator against the mounting bracket and install the mounting bolts.
  3. Rotate the tensioner counterclockwise and install poly-V belt.
  4. Connect the negative battery cable.

3.3L and 3.8L Engines
The 3.3L and 3.8L engines were equipped with the Nippondenso alternators.
  1. Disconnect the negative battery cable.
  2. Remove the alternator drive belt, by relieving the tension on the dynamic tensioner.
  3. Loosen the nut on the support bracket at the exhaust manifold, do not remove it.
  4. Remove the alternator tensioner/power steering bracket bolt.
  5. Remove the tensioner stud nut and remove the tensioner.
  6. Remove the alternator mounting bolts.
  7. Remove the power steering reservoir from the mounting bracket, do not disconnect the hoses, and position it out of the way.
  8. Remove the alternator support bracket bolts. Remove the intake plenum to alternator bracket bolt and remove the alternator support bracket from the engine.
  9. Remove the alternator from the engine and disconnect the electrical leads.
To install:
  1. Install the alternator in position on the engine and connect the electrical leads.
  2. Install the alternator support bracket, tighten the retaining bolts to 40 ft. lbs. (54 Nm).
  3. Install the power steering reservoir on the mounting bracket.
  4. Install the alternator mounting bolts, tighten the bolts to 40 ft. lbs. (54 Nm).
  5. Install the tensioner and tensioner mounting stud. Install the retaining nut on the exhaust manifold.
  6. Install the alternator belt, insert a 1 / 2 in. extension into the square hole in the tensioner and turn the tensioner. Tighten the tensioner bolt.
  7. Connect the negative battery cable.

Hope this help (remember comment and rated this).

Apr 01, 2010 | 1994 Dodge Caravan

1 Answer

How to fit a alternator belt on a 1.8 diesal escort van 51plate


This should be the same as a car, jack the front of the car up put stands under, remove front wheels, remove bottom cover (about 7 screws), Remove powersteering pump pully 3 bolts, remove and refit new belt and P/S pully, you might get away with not having to adjust alt but if you have to youll need a 13mm spanner to undo the locking bolt then pull the alt tight (its really tight u might need a bar), once all done replace in reverse order.

Dec 16, 2009 | 2001 Ford Escort ZX2

1 Answer

How do you change the alternater belt on 1994 toyota corolla 1.6l


Loosen alternator bracket bolt at top of alternator.

Loosen adjustment lock bolt on passenger side of alternator.

Loosen adjustment bolt under front of alternator until belt can be removed.

Nov 23, 2009 | 1994 Toyota Corolla

2 Answers

Directions on how to remove the alternator on 1989 900 Saab. Does anything have to be removed to be able to get the alternator off. Also, any tricks to get belts off first?


Removing the alternator isn't the easiest job on this car!

The long bolt that allows the alternator to pivot to adjust belt tension ISN'T the bolt to be removed; remove the two bolts that hold the mounting bracket to the engine block. One is at the end of the alternator (away from the belt), the other is above the end of the adjusting bolt, not far away from the first bolt. Slacken the tension off the belt by loosening the adjusting bolt, then undo the two bolts holding the bracket to the engine block.

While you have the alternator off, check the bushings of the tension adjusting bolt; if worn/sloppy they should be pressed out and replaced; it'll extend the life of the alternator bearings.

Good luck!

Saabreur

Jul 09, 2009 | 1989 Saab 900 4 Door

1 Answer

1988 saab 900 how to remove pully on alternater


Removing the alternator isn't the easiest job on this car!

The long bot that allows the alternator to pivot to adjust belt tension ISN'T the bolt to be removed; remove the two bolts that hold the mounting bracket to the engine block. One is at the end of the alternator (away from the belt), the other is above the end of the adjusting bolt, not far away from the first bolt. Take the tension off the belt, then slacken the two bolts holding the bracket to the engine block.

While you have the alternator off, check the bushings of the tension adjusting bolt; if worn/sloppy they should be pressed out and replaced; it'll extend the life of the alternator bearings.

Jun 26, 2009 | 1988 Saab 900

1 Answer

Alternator bracket fanbelt slippage


fan belt adjuster locking bolt & nut

Jan 05, 2009 | 1999 Ford Escort

Not finding what you are looking for?
1999 Ford Escort Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...