Question about 2004 GMC Envoy

1 Answer

Engine has no starting power only clicking noise from engine

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • GMC Master
  • 1,098 Answers

HOW OLD IS YOUR BATTERY? POSSIBLE BATTERY NEEDS REPLACEMENT. POSSIBLE THE STARTER SOLENOID IS NOT WORKING,LOOSE EARTHING WIRE.

Posted on Nov 08, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1999 ford econoline will not start. its making that clicky noise but not turning over


It sounds like your Starter Solenoid is stuck. Replace your starter and you should be alright.

Feb 03, 2011 | 1999 Ford Econoline

1 Answer

Having problems with car starting. Battery is good, iol recently changed, although was very low prior to change. Also had transmission fluid flushed. The car sounds like it wants to turn over, but...


http://www.fixya.com/cars/r7030578-engine_turns_over_but_wont_start

IF your engine is turning but not starting, try the above link to my tip.
IF youre not even getting the engine to turn over, the click you hear, may be the starter trying to throw the gear out to engage the flywheel (sounds like "clunk"), or if is a rapid ("clicky-clicky') sound, that's you're starter relay under your hood in you're realy/fuse panel

Dec 01, 2010 | 1999 Saturn SL

1 Answer

I was trying to start my car tonight, and it woouldnt turn over. I have all my lights so I know that it is not the alternator or the battery, could it be my starter?


Could be low battery. Did you hear a chattering sound when you tried to start it? Normal battery voltage fully charged is actually over 13 volts. Try to jump start it. If you don't get a response out of it, then check your fuses. Check engine bay fuses (under the hood) and interior fuses (inside the car-drivers side) Also could be starting relay. have a second person turn the key and you listen for a relay under the hood. If the IGN relay does not pull in, hten you either have a bad fuse, or bad relay or bad ignition keyswitch or bad transmission neutral position switch. if relay pulls in and then chatters, it does not have enough voltage to stay pulled in and attempt to run the starter motor at the same time, which is why it will make that fast clicky-clicky noise. if it does pull in and nothing happens then your starter is either bad or not connected electrically.

Nov 22, 2010 | 1994 Pontiac Grand Prix

1 Answer

Lifter clicking sound in 4.6 engine


it could be your tensioner. it sounds like a clicky squeak. sometimes it may go away but it always comes back. thats what mine is but i havent fixed it yet. i doubt you can grease it, you probably need it replaced. not expensive, at least the part should be under 100 bucks

Nov 22, 2008 | 1997 Lincoln Continental

1 Answer

My son ran the TDI bone dry of desiel fuel and now it will not start


not shore about VW's but on a GM diesel there is a priming procedure that has to be done.
if there is no manual primer try turning the car to the on position (with the engine off) and wait for five seconds and do this at least five times wait for 30 seconds with the key off and then turn the key to on wait five seconds then start.

Oct 10, 2008 | 1997 Volkswagen Passat

1 Answer

Xterra repair


Since this is an intermittent problem, first try to determine if the problem arises due to one of these many intermittent problems:

* Vehicle vibration
* Heat sensitive
* Freezing
* Water intrusion
* Electrical load
* Cold or hot start up

If you can't isolate the cause of the intermittent problem, you can try adjusting the Idle Speed/Ignition Timing/Idle Mixture Ratio:

Idle Speed/Ignition Timing/Idle Mixture Ratio Adjustment

PREPARATION
1) Make sure that the following parts are in good order.

* Battery
* Ignition system
* Engine oil and coolant levels
* Fuses
* ECM harness connector
* Vacuum hoses
* Air intake system
* (Oil filler cap, oil level gauge, etc.)
* Fuel pressure
* Engine compression
* EGR valve operation (If so equipped)
* Throttle valve
* Evaporative emission system

2) On air conditioner equipped models, checks should be carried out while the air conditioner is OFF.
3) On automatic transmission equipped models, when checking idle rpm, ignition timing and mixture ratio,
checks should be carried out while shift lever is in “N” position.
4) When measuring “CO” percentage, insert probe more than 40 cm (15.7 in) into tail pipe.
5) Turn off headlamps, heater blower, rear defogger.
6) Keep front wheels pointed straight ahead.
7) Make the check after the cooling fan has stopped.

INSPECTION PROCEDURE

1 INSPECTION START
1. Visually check the following:
I Air cleaner clogging
I Hoses and ducts for leaks
I EGR valve operation (If so equipped)
I Electrical connectors
I Gasket
I Throttle valve and throttle position sensor operation
2. Start engine and warm it up until engine coolant temperature indicator points to the middle of gauge.
Ensure engine stays below 1,000 rpm.
3. Open engine hood and run engine at about 2,000 rpm for about 2 minutes under no-load.
4. Perform diagnostic test mode II (Self-diagnostic results).
OK or NG
OK ' GO TO 2.
NG ' 1. Repair or replace components as necessary.
2. GO TO 2.

2 CHECK IGNITION TIMING
1. Run engine at about 2,000 rpm for about 2 minutes under no-load.
2. Rev engine (2,000 to 3,000 rpm) two or three times under no-load, then run engine at idle speed.
3. Turn off engine and disconnect throttle position sensor harness connector.
4. Start and rev engine (2,000 - 3,000 rpm) two or three times under no-load, then run at idle speed.
5. Check ignition timing with a timing light.
15°±2° BTDC (in “P” or “N” position)
OK or NG
OK ' GO TO 4.
NG ' GO TO 3.

3 ADJUST IGNITION TIMING
1. Adjust ignition timing by turning distributor after loosening securing bolts.
2. Turn off engine and connect throttle position sensor harness connector to throttle position sensor.
' GO TO 2.


4 CHECK BASE IDLE SPEED
1. Check idle speed.
700±50 rpm (in “P” or “N” position)
OK or NG
OK ' GO TO 6.
NG ' GO TO 5.

5 ADJUST BASE IDLE SPEED
1. Rev engine (2,000 to 3,000 rpm) 2 or 3 times under no-load then run engine at idle speed.
2. Adjust idle speed by turning idle speed adjusting screw.
700±50 rpm (in “P” or “N” position)
' GO TO 6.

6 CHECK TARGET IDLE SPEED
1. Turn off engine and connect throttle position sensor harness connector.
2. Start and rev engine (2,000 to 3,000 rpm) 2 or 3 times under no-load then run at idle speed.
3. Check idle speed.
750±50 rpm (in “P” or “N” position)
OK or NG
OK ' GO TO 9.
NG ' GO TO 7.

7 DETECT MALFUNCTIONING PART
Check the following.
1. Check IACV-AAC valve and replace if necessary.
2. Check IACV-AAC valve harness and repair if necessary.
3. Check ECM function by substituting another known good ECM.
(ECM may be the cause of a problem, but this is rarely the case.)
' GO TO 9.

9 CHECK FRONT HEATED OXYGEN SENSOR LH SIGNAL
1. Run engine at about 2,000 rpm for about 2 minutes under no-load.
2. Set “Left bank front heated oxygen sensor monitor” in the Diagnostic Test Mode II.
3. Make sure that MIL goes on more than 5 times during 10 seconds at 2,000 rpm.
OK or NG
OK ' GO TO 12.
NG (MIL does not blink.) ' GO TO 17.
NG (MIL blinks less than 5 times.)
' 1. Replace front heated oxygen sensor LH.
2. GO TO 10.


10 CHECK FRONT HEATED OXYGEN SENSOR LH SIGNAL
1. Warm engine to normal operating temperature.
2. Run engine at approx. 2000 rpm for approx. 2 minutes under no-load.
3. Set “Left bank front heated oxygen sensor monitor” in the Diagnostic Test Mode II.
4. Make sure that MIL goes on more than 5 times during 10 seconds at 2,000 rpm.
OK or NG
OK ' GO TO 13.
NG ' GO TO 11.

11 DETECT MALFUNCTIONING PART
Check the following.
1. Check fuel pressure regulator.
2. Check mass air flow sensor and its circuit.
3. Check injector and its circuit.
Clean or replace if necessary.
4. Check engine coolant temperature sensor and its circuit.
5. Check ECM function by substituting another known good ECM.
(ECM may be the cause of a problem, but this is rarely the case.)
' GO TO 2.


13 CHECK FRONT HEATED OXYGEN SENSOR RH SIGNAL
1. Set “Right bank front heated oxygen sensor monitor” in the Diagnostic Test Mode II.
2. Make sure that MIL goes on more than 5 times during 10 seconds at 2,000 rpm.
OK or NG
OK ' INSPECTION END
NG (MIL does not blink.) ' GO TO 16.
NG (MIL blinks less than 5 times.)
' 1. Replace front heated oxygen sensor RH.
2. GO TO 14.


14 CHECK FRONT HEATED OXYGEN SENSOR RH SIGNAL
1. Warm engine to normal operating temperature.
2. Run engine at approx. 2000 rpm for approx. 2 minutes under no-load.
3. Set “Right bank front heated oxygen sensor monitor” in the Diagnostic Test Mode II.
4. Make sure that MIL goes on more than 5 times during 10 seconds at 2,000 rpm.
OK or NG
OK ' INSPECTION END
NG ' GO TO 15.

15 DETECT MALFUNCTIONING PART
Check the following.
1. Check fuel pressure regulator.
2. Check mass air flow sensor and its circuit.
3. Check injector and its circuit. Clean or replace if necessary.
4. Check engine coolant temperature sensor and its circuit.
5. Check ECM function by substituting another known good ECM.
(ECM may be the cause of a problem, but this is rarely the case.)
' GO TO 2.
16 CHECK FRONT HEATED OXYGEN SENSOR RH HARNESS
1. Turn off engine and disconnect battery ground cable.
2. Disconnect ECM harness connector.
3. Disconnect front heated oxygen sensor RH harness connector.
4. Check harness continuity between ECM terminal 50 and front heated oxygen sensor RH harness connector.
Continuity should exist.
OK or NG
OK ' 1. Connect ECM harness connector.
2. GO TO 18.
NG ' 1. Repair or replace harness.
2. GO TO 9.

17 CHECK FRONT HEATED OXYGEN SENSOR LH HARNESS
1. Turn off engine and disconnect battery ground cable.
2. Disconnect ECM harness connector.
3. Disconnect front heated oxygen sensor LH harness connector.
4. Check harness continuity between ECM terminal 51 and front heated oxygen sensor LH harness connector.
Continuity should exist.
OK or NG
OK ' 1. Connect ECM harness connector.
2. GO TO 18.
NG ' 1. Repair or replace harness.
2. GO TO 9.

18 PREPARATION FOR “CO” % CHECK
1. Disconnect engine coolant temperature sensor harness connector.
2. Connect a resistor (4.4 kW) between terminals of engine coolant temperature sensor harness connector.
' GO TO 19.

19 CHECK “CO” %
1. Start engine and warm it up until engine coolant temperature indicator points to the middle of gauge.
2. Rev engine (2,000 to 3,000 rpm) two or three times under no-load, then run engine at idle speed.
3. Check “CO” %.
Idle CO: 1.5 - 9%
After checking CO%,
a. Disconnect the resistor from terminals of engine coolant temperature sensor.
b. Connect engine coolant temperature sensor harness connector to engine coolant temperature sensor.
OK or NG
OK ' 1. Replace front heated oxygen sensor LH.
2. GO TO 10.
NG ' GO TO 20.

20 DETECT MALFUNCTIONING PART
Check the following.
1. Connect front heated oxygen sensor harness connectors to front heated oxygen sensors.
2. Check fuel pressure regulator.
3. Check mass air flow sensor and its circuit.
4. Check injector and its circuit.
Clean or replace if necessary.
5. Check engine coolant temperature sensor and its circuit.
6. Check ECM function by substituting another known good ECM.
(ECM may be the cause of a problem, but this is rarely the case.)
' GO TO 2.

Aug 17, 2008 | 2000 Nissan Xterra

Not finding what you are looking for?
2004 GMC Envoy Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...