Question about 1994 Ford Aerostar Extended

Open Question

Need to replace window on driver side by quarter panel

Window has been smashed - it is the back window on driver's side

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
michigan man
  • 3533 Answers

SOURCE: 2004 crown victoria lx smashed driver side window

normally you have to loosen the track and it comes out as one whole assembly stop by a dealer in the parts department and ask them to print out a diagram or show them the part you are having the problem with

Posted on Jan 09, 2009

Ad
  • 93 Answers

SOURCE: R/H rear quarter window repalcement

tv is the wrong adhesive. you must use urethane with a primer. it is available at any QUALITY parts store (NAPA or Carquest comes to mind)


Material Item Specification Urethane Metal Primer Essex U-413
WSB-M2G234-C Urethane Glass Prep Essex U-401
WSB-M5B280-C Urethane Glass Primer Essex U-402
WSB-M2G314-B Urethane Adhesive Essex 400-HV
WSB-M2G316
Removal
All vehicles
ani_caut.gif WARNING: To prevent glass splinters from entering the eyes or cutting the hands, wear safety glasses and heavy gloves when cutting the glass from the vehicle.

  1. Remove the C-pillar trim panels. For additional information, refer to Section 501-05.
3-Door, 5-Door
  1. ani_caut.gif CAUTION: Make sure the cutting blades are changed where the cutting depth changes to avoid damage to the body and trim panels.
    NOTE: Some resistance may be encountered when cutting through the glass locating pegs in the lower corners of the glass.
    NOTE: Lubricate the existing urethane adhesive with water to aid the special tool while cutting.
    Using the special tool, place the flat side of the knife against the quarter glass window. Start at the top and work towards the corners cutting to the given maximum depths:
    1. 20 mm
    1. 60 mm
    1. 75 mm
    1. 90 mm
    a0074767.gif
Wagon
  1. ani_caut.gif CAUTION: Make sure the cutting blades are changed where the cutting depth changes to avoid damage to the body and trim panels.
    NOTE: Some resistance may be encountered when cutting through the glass locating pegs in the upper right and lower left corners of the glass.
    NOTE: Lubricate the existing urethane adhesive with water to aid the special tool while cutting.
    Using the special tool, place the flat side of the knife against the quarter glass window. Start at the top and work towards the corners cutting to the given maximum depths:
    1. 20 mm
    1. 30 mm
    1. 50 mm
    1. 40 mm
    a0074768.gif
4-Door
  1. ani_caut.gif CAUTION: Make sure the cutting blades are changed where the cutting depth changes to avoid damage to the body and trim panels.
    NOTE: Some resistance may be encountered when cutting through the glass locating pegs in the upper right and lower left corners of the glass.
    NOTE: Lubricate the existing urethane adhesive with water to aid the special tool while cutting.
    Using the special tool, place the flat side of the knife against the quarter glass window. Start at the top and work towards the corners cutting to the given maximum depths:
    1. 20 mm
    1. 25 mm
    1. 45 mm
    1. 50 mm
    1. 55 mm
    1. 70 mm
    1. 150 mm
    a0074769.gif
All vehicles
  1. Remove the rear quarter window glass.
  1. Using a soft brush or vacuum, remove any dirt or foreign material from the pinch weld.
Installation
ani_caut.gif CAUTION: When installing urethane installed glass parts, the vehicle must not be driven until the urethane adhesive has cured. At temperatures above 21°C (70°F) and relative humidities above 50%, adequate cure time is typically 24 hours. (Refer to Essex drive away chart for the cure times as temperatures and humidity vary.) Inadequate or incorrect curing can adversely affect the retention of the quarter window glass.
  1. NOTE: Avoid scratching the pinch weld.
    Trim the remaining urethane adhesive. The urethane adhesive must be smooth and free of cuts and contamination after trimming. Avoid touching the urethane adhesive after preparation.
    a0005586.gif
  1. Apply the urethane metal primer to any exposed or damaged metal on the pinch weld.
  1. If reinstalling the original rear quarter window glass, remove the excess urethane adhesive.
  1. Clean the rear quarter window glass with a non-alcohol based window cleaner.
  1. ani_caut.gif CAUTION: Wipe off the urethane glass prep immediately after each application because it flash dries.
    If installing a new rear quarter window glass, apply urethane glass prep twice around the glass surface to be urethaned.
  1. If installing a new rear quarter window glass, apply urethane glass primer to the same area that was prepped in the previous step. Allow 5 minutes to dry.
  1. Cut the urethane adhesive applicator tip to specification.
    a0016835.gif
  1. Apply a bead of urethane adhesive on top of the existing urethane bead on the pinch weld. Make sure that all gaps in the urethane adhesive are smoothed into one continuous bead.
  1. Position the rear quarter window glass to the flange, and press the retaining tabs into the flange to engage.
    an0459b.gif
  1. Install the rear quarter window glass.
  1. Check the rear quarter window glass installation for air or water leaks through the urethane seal.
  1. Install the C-pillar trim panels. For additional information, refer to Section 501-05.

Posted on Jun 02, 2009

  • 66 Answers

SOURCE: I need a driver side door panel replacement, where do i buy?

try e-bay , lkq auto parts or this one
mpsautosalvage.com.tons of mustang parts!!!!

Posted on Oct 28, 2009

  • 3 Answers

SOURCE: do I need remove door panel to replace drivers

Give me some more information about this problem. May be i can help.

Posted on Jul 14, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2008 Mitsubishi lancer cj my08 drivers side back door wont open from inside or outside. Small 1/4 window has been smashed and im guessing there might glass stuck in the locking mechanism but I dont know...


Wind the window down completely. You should be able to get a hooked wire down behind the glass to snag the lock mechanism. You could also call your auto club for assistance.

Sep 16, 2014 | 2008 Mitsubishi Lancer

1 Answer

20010 grand caranvan. drivers side near or on side mirror. whistling sound. What to do to fix?


leak in rubber trim molding around window or door jamb..check for tears or smashed rubber..replace with foam self adhesive

Jan 29, 2011 | Dodge Caravan Cars & Trucks

1 Answer

Driver's side window smashed


phillips screw driver, 10mm socket/rachet, vaccuum cleaner and yes you can. one of the more simple glass installations.

Sep 14, 2009 | 1998 Toyota Camry

1 Answer

Power window failure on drivers side


Sometrimes the wires between the door and the body break from opening and closing the door, check your window motor for paower with a test light, if no power, you have a broken wire, between the door and body

Dec 22, 2008 | 1999 Saturn SL

1 Answer

2004 crown victoria lx smashed driver side window


normally you have to loosen the track and it comes out as one whole assembly stop by a dealer in the parts department and ask them to print out a diagram or show them the part you are having the problem with

Aug 27, 2008 | 2003 Ford Crown Victoria

Not finding what you are looking for?
1994 Ford Aerostar Extended Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...