Question about 1996 Jeep Grand Cherokee

1 Answer

Front turn signal on with running lights

My driver front turn signal blew and after replacement it comes on with the running lights.it isnt as bright as the run light.the drivers side flashes fast even with the run lights off.hazards work fine

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 52 Answers

You may want to double check to make sure you put in the correct bulb. It sounds like you have a brake bulb in there...
Good luck!

Posted on Jan 06, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Regular headlights will not come on, only brights


There is a head lamp driver module for low beams, I can't tell if module is faulty? Check voltage and ground for module. Can you check applicable trouble codes? The BCM does have some control on that module, pulse/width modulated ground. Some of the national brand autostores will check codes for free.

Note the wiring.
25432079-f354phfyjkegikfzmbtgakwh-1-0.jpg

Feb 15, 2015 | 2008 Chevrolet Trailblazer

1 Answer

On my 1999 Olds Intrigue I have never had to turn on my lights at night. All night time driving lights come on automatically until recently. Now only the headlights come on.To get the dash lights,tail...


Without testing i would say you have DRL control module problem , But that would just be a guess .
In the night mode, the DRL ambient light sensor senses darkness. Then, the DRL module turns off the front turn lamps and turns on the headlamps through circuit 10. The DRL module also turns on the park, side marker, license, and tail lamps. If the engine should stall with the DRL control module in the night mode, the DRL control module will turn off the headlamps and leave the side marker, park, license and tail lamps on while the engine is being cranked. The headlamp switch operates as usual.
The Daytime Running Lamps (DRL) control module is designed to automatically operate exterior lights depending on outside light conditions. The DRL control module operates in two modes, the day mode and the night mode. In the day mode, the DRL ambient light sensor senses daylight. Then, the DRL control module turns on the front turn lamps (non-flashing) if under the following conditions:
• The ignition switch is on.
• The headlamps switch is in the OFF position.
• The park brake is released.

The brightness of the Vacuum Fluorescent (VF) displays is controlled by two signals: the park lamps on signal (circuit 230) and the VF dimming signal (circuit 308). With the park lamps on, the VF display of the radio, heater, A/C control (with RPO CJ2) and the instrument cluster will dim for nighttime viewing. When the park lamps on signal is not present (park lamps off), the VF displays are at high brightness for daytime viewing. When the park lamps are on, the I/P lamp dimmer switch provides a signal (VF Dimming Signal circuit 308) which controls the brightness of the VF displays when the I/P lamp dimmer switch is adjusted.

Do the Daytime running light's work ?

Nov 18, 2017 | Cars & Trucks

1 Answer

I am having a problem with my 1994 E-150 blowing 15 amp fuses on the turn signals. I checked the book and the DRL module is also on that circuit. The lights haven't come on in the day as they should for...


that would only have to do with the headlights and the running lights check all the bulb connections in the front and the wires in the back, also whit the turn signals on see witch one is not as bright or isnt lighting at all and thats were you should start

Sep 27, 2013 | Ford E-150 Cars & Trucks

1 Answer

Ok, had a trailer wire box attached to rear drivers side-wife left it hanging out and ran over it. Now I have no rear driver tail light or front amber running light. All turn signals and running lights...


check all your fuses. something may have shorted out and blew out a fuse.if you don`t have blown fuse there is a short somewere.you will have to locate it.

Nov 26, 2010 | 1994 Jeep Cherokee

4 Answers

Front driver side turn signal light doesn't flash.replaced bulb,replaced socket,all other lights work on emergency flasher,except front driver side.rear driver side turn signal light works,but flashes...


replace flasher......usually located in fuse block area...listen in this area....select passenger side ...then select driver side...you can hear flasher clicking...you have seperate flashers for each...FLASHERS are small cubes plugged into fuse block....probable bad driverside flasher

May 09, 2009 | 1998 Buick Century

1 Answer

Left Signal light isnt blinking on my 2000 300M Chrysler


you need to replace the rear driver side light bulb. it will fix the problem.

Feb 27, 2009 | 2000 Dodge Ram 1500 Truck

3 Answers

Turning signals dont blink


Problem is the Turn Signal "FLASHER" unit, 1.Turn on Emergency FLASHERS 2. Go under Dash while they are on Listen -for Clicking sound then feel for it 3. Should Be a Silver Round Unit About as Big IN ROUND as Half dollar coin 4. ok now Look Around for the SAME EXACT Thing Clipped onto Something Under dash At Driver side Usually Between Steering wheel and Center HUMP in Floor, 5. once you find it Take OUT the first One you Found Emergency FLASHER) and 6. Put it In Place of Turn Signal Flasher, 7. Turn off Emergency Flashers- Turn Key in "ON" Position but don't start then Try Turn Signals. Yaaaa !!!! they work ?? LoL hopefully this Does the trick, if they work Buy new one and Replace Always Use NEW For TURN Signals as they are used Much More than Emergency Flashers. Hope this is Good Instructions For you and Helps you Solve The Problem, Please DONT Forget to RATE ME Thank you Rejakwilson@aol.com

Jan 18, 2009 | 1986 Oldsmobile Cutlass Supreme

1 Answer

2000 Accord turn signal problem


either the front or the rear turn signal bulb is blown, that is why the flash frequency is high. replace the bulb and the problem will be solved. best to replace both the front and rear turn signal bulbs. good luck.

Aug 29, 2008 | 2000 Honda Accord

Not finding what you are looking for?
1996 Jeep Grand Cherokee Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...