Question about Mitsubishi Cars & Trucks

Open Question

Detached door handle of mitsubishi adventure - Mitsubishi Cars & Trucks

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3074 Answers

SOURCE: Exterior, rear, passenger door handle will not

you will need to remove the panel, usually for screws located on arm rest,door handle and sometimes around the middle of the panel behind a round plastic cover. Once all the screws are out the panel pops off, you will need to disconnect the power switches from the inside. Then look at the inside of the door, there is a retaining clip that holds the lever inside the door handle it may have fallen off or the handle cracked. Hope this helped tim

Posted on Sep 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing door handle on a 2005 Mitsubishi Endeavor XLS rear passenger door handle


Remove inner door handle and arm rest if applicable, with a flat screw driver or chisel leaver door cover away so as to gain access, undo the screws on old handle,remove rods ,then remove handle fit ,new handle .mark rods with paint so they go back in the same place.

Apr 24, 2017 | Mitsubishi Cars & Trucks

1 Answer

2004 Hyundai Santa Fe rear driver side door the outside door handle never worked you can only open it from the inside. accidentally flipped on the child safety lock now I can't open the door at all


It is fairly clear the door handle has detached from the wire that releases the latch. As you cnnot open from the interior handle currently you can only detach the door card and reatach the wire to the door handle. You might have to remove the seat adjacent to the door. I think it is probably a weekend job if you intend doing it yourself. There is no other way it could be done without inflicting damage I think. Essential for safety if you are carrying children/pets in the rear
Good Luck

Jun 01, 2015 | Hyundai Cars & Trucks

1 Answer

How to get the spare tire of my mitsubishi adventure


pull the handle beside the rear seat to remove the cover..and then loosen the bolt w/ your tire wrench..

Jun 04, 2011 | Mitsubishi Montero Cars & Trucks

1 Answer

Thank you for your response , been going crazy here...got panel off enough to put hand in but don't know where to pull to unlock door.



Jaguar 2000-06 - Locks & Lock Systems
Power Door Locks - Removal & Installation

Door Lock Switch
Door Lock Diagnosis & Testing

  1. Visually inspect the following:
    Misaligned door(s), hood or luggage compartment lid Door latches Actuating rod Exterior door handle Interior door handle Door lock cylinder Cable Luggage compartment lid exterior release switch Fuse(s) Wiring harness Electrical connector Door lock actuator Remote transmitter batteries Vehicle battery Remote transmitter Door lock switch Front electronic module
  2. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.

Door Lock Motor
Coupe And Convertible
  1. Turn ignition key to position II.
  2. Motor door glass to fully raised position.
  3. Turn ignition key to position O.
  4. Disconnect the negative battery cable.
  5. Remove door casing for access.
  6. Remove door water shedder.
  7. Position PVC secondary water shedder for access.
  8. Slacken and remove the door glass rear runner lower securing screws.
  9. Reposition door glass rear runner. Mark the position of the glass rear runner upper securing screw.
  10. Slacken and remove the upper securing screw and move the runner away from the glass.
  11. Disconnect door handle and lock barrel (driver door only) operating rods from latch links.
  12. Slacken and remove the three latch assembly securing screws and position latch for access.
  13. Remove latch motor harness multiplug from mounting bracket and disconnect multiplug.
  14. Release operating cable from door handle. Move inner door handle to the locked position. Remove operating cable outer abutment from support bracket. Disconnect cable inner from door inner handle.
  15. Remove lock motor assembly from door.
  16. To install, reverse removal procedure.

    zjlimited_378.jpg

    Fig. Removing door lock actuator


Sedan
  1. Remove the door window glass
  2. Detach the interior door handle.
  3. Detach the actuator remote cable from the interior door handle.
  4. Remove the interior door handle.
  5. Detach the door window glass run.
  6. Remove the exterior door handle retaining screws.
  7. Remove the front door actuator retaining screws.
  8. Reposition the front door actuator and exterior handle.
  9. Remove the front door actuator and exterior handle.
  10. Disconnect the front door actuator remote cable.
  11. Detach the door lock cylinder connecting rod (1).
  12. Detach the exterior door handle connecting rod (2).
  13. Remove the front door actuator (3).
  14. To install, reverse removal procedure.

    zjlimited_379.jpg

    Fig. Removing door lock motor-Sedan



Hope this helps.

Dec 31, 2010 | 2002 Jaguar X-Type

1 Answer

How do I change the speaker in 2007 sierra


This procedure work for door lock, but necessary you need take off the trim panel, then could helpfull...

zjlimited_205.jpg

Fig. Exploded view of the front door trim panel - 2005-06 and 2007 Classic models (click image for zoom)

  1. Disconnect the battery ground cable.
  2. Disable the Supplemental Restraint System.
  3. Remove the door trim panel. Refer to the illustration for the mounting screw and lock tab locations. After detaching the hardware, carefully pull it away, then lift it off the door just far enough to detach the electrical connections from it.
  4. Carefully detach the water shield from the door; this will be reused upon installation.
  5. Disconnect the inside door lock rod from the handle retainer clip.
  6. Detach the door lock rod from the retainer clip.
  7. Remove the rubber plug to access the outside handle rod. Disengage it from the clip and disconnect the lock cylinder rod.
  8. Detach the electrical connector and remove the lock from the vehicle.
  9. Installation is the reverse of removal. When installing the lock, tighten the screws to 89 inch lbs. (10 Nm).

Dec 09, 2010 | 2008 GMC Sierra 1500

1 Answer

Howdo i romove the spare tire beneath my mitsubishi adventure gls 2007 model


Hi and welcome to FixYa. I am Kelly.

Open the back door. On the RH side there is a round button type handle. Pull the handle. The nut cover for the spare tire will open. Use the tire lug wrench to loosen the nut substantially. Then push up on the frame and swing the nut and threaded lock assy out of the retaining area of the spare tire frame. Then slide the tire out for use.

Thanks again for using FixYa.

Kelly

Apr 04, 2010 | 2000 Mitsubishi Montero Sport

1 Answer

Changing interior door handle camry 1995


With a little dexterity, you can do this without removing the door panel. Pop the center tab on the handle with a small flathead. Underneath is the the screw holding the handle. Undo it. Shimmy and loosen the handle to separate it from the door panel. Detach it from the door mechanism transfer bars. Replace.

Feb 13, 2010 | 1995 Toyota Camry

1 Answer

How to replace a window on a 2002 saturn sl2 with power windows. i cant get the door handle assembly off


As per the Haynes manual for your vehicle.
DOOR WINDOW GLASS-REMOVAL AND INSTALLATION:
1. Remove the door outer panal.
2. Lower the window glass.
3. remove the two nuts and one screw securing the glass.
4. Remove the glass by lifting it up carefully and rotating it inward.
5. Installation is reversal of removal.

DOOR OUTER PANAL-REMOVAL AND INSTALLATION:
1. Remove door trim panal.
2. Remove the outside mirror. Remove the foam block from the mirror opening.
3. Remove the outside door handle.
4. Open the door and pry thhe outer sealing strip out of the window glass opening.
5. remove the door panal screws.
6. Detach the front and rear of the outer panel, then lift it toward the rear to remove it.
7. Installation is the reverse of the removal procedure. Apply thread locking compound to the panel retaining screws.

OUTSIDE DOOR HANDLE-REMOVAL:
1. Pull handle out and puch the centers of the retaining pins through the pins, then remove them and detach handle. (These pins are located underneath the handle.

Hope this helps, let me know if you need any other help.

Feb 06, 2010 | 2002 Saturn L-Series

1 Answer

How to remove rear door panels on a 2003 ford f 250to get to door switch


Tailgate latch, handle and lock
  • Open the tailgate.
  • Remove the two bolts and detach the door stop.
  • Lower the tailgate and remove the tailgate access cover.
  • Disconnect the control rods.
  • Detach the retaining nuts and remove the handle and lock cylinder assembly from the tailgate.
...
Door trim panels
  • Disconnect the cable(s) from the negative battery terminal(s).
  • On manual window equipped models, pull the window crank cover aside, remove the screw and detach the handle.
  • On the front door of power window equipped models Pry up on the retaining clip at the front edge of the armrest and lift the armrest switch control plate out and disconnect the electrical connections,then remove the retaining bolt from the opening.
  • Use a small screwdriver to pry off the courtesy light cover for access to the trim panel retaining bolt.
  • Carefully pry off the mirror trim panel from above the front edge of the door panel.
  • Once all of the bolts are removed, remove the trim panel by gently pullingit up and out .Detach the courtesy light bulb housing from the panel.
  • For access to the inner door components, remove the speaker (if it would interfere with watershield removal) and the screws from the trim piece at the lower trailing corner of the door, then carefully peel the watershield from the door.
  • Remove the screws securing the latch.
  • Working through the large access hole, position the latch as necessary to disconnect the electrical connector and disengage the outside door handle and outside lock cylinder to latch rods and the inside handle-to-Iatch cable.
  • Detach the locking rods by unsnapping The remaining outside handle retaining nut can be reached through the access hole in the door frame and the upper striker the portionof the plastic clip engaging the connecting rod, then pulling the rod out of its locating hole.
  • Position the latch as necessary to disengage the door lock actuator hook. Detach the cable cover and disconnect the cable from the latch. Remove the latch assembly from the door.

Oct 30, 2009 | 2003 Ford F250 Super Duty Crew Cab

1 Answer

Kids keep pulling on our denali door handles. One


pull the pannel off from the inside, you should see some bolts that attach to the handle.

Aug 11, 2009 | 2007 GMC Yukon Denali

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

164 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...