Question about 1995 Honda Accord

1 Answer

Need to find inlet heater hose location - 1995 Honda Accord

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Honda Master
  • 75,117 Answers

Go to this link and scroll down to the diagram of the cooling system hoses. The inlet hose is the hotter of the 2 and in most cases slightly larger in diameter.

Posted on Nov 08, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for location on engine side of heater core hoses. I can see the outlet hose but am unable to locate the inlet hose to the engine.


Sounds like an air pocket. Follow the bleed procedure for you vehicle. Many vehicles have a bleed valve for this issue..not familiar with yours but a Google search should answer that question.

Oct 28, 2016 | 2005 Hyundai Santa Fe

2 Answers

Where is the inlet heater hose located on a 2005 Hyundai Elantra?


You wouldn't even be able to see it from this angle. It will be on the firewall. There will be two hoses (rubber) next to each other that are the same size. They are likely 5/8" hoses. The inlet is typically on the passenger side. Make sure the hoses are rubber. The A/C lines run into the firewall near that area but they are metal.

Dec 29, 2014 | 2005 Hyundai Elantra

1 Answer

Im trying to flush the cooling system on a '97


Not positive about that engine, but the usual method is the heater inlet will come off the cylinder head somewhere and to the firewall, and the heater outlet (the return hose) will be at same place on the firewall and go to the water pump, very close or at the fitting where the lower radiator hose attaches to the water pump inlet.

Jul 21, 2013 | Cars & Trucks

1 Answer

Need help finding inlet heater hose from fire wall to engine


The inlet going TO the heater core should be the top one (I think) but in any case it would be the one with the heater control valve on it (see picture below) Hope this is what you were looking for....

3_5_2012_4_38_32_pm.jpg

Mar 05, 2012 | 1998 Lexus ES 300

1 Answer

How to replace the heater core to a chevy astro 2003


  1. Drain the engine coolant.
  2. Reposition the outlet heater hose clamp at the heater core.
  3. Remove the outlet heater hose from the heater core.
  4. Reposition the inlet heater hose clamp at the heater core.
  5. Remove the inlet heater hose from the heater core.
  6. Remove the screws that retain the cover to the heater case assembly. This is located underneath the dash on the passenger side.
  7. Remove the straps that retain the heater core to the heater case assembly.
  8. Remove the heater core from the vehicle.

Sep 05, 2011 | 2002 Chevrolet Astro

1 Answer

Need to replace heater core on 84 chevy celebrity


First, drain your system's coolant into a container (and dispose of properly)
Locate the two hoses that go into your firewall. These hoses go into and out of the hearer core and remove them. There should also be rubber insulators on the inlet and outlet of the heater core. Unscrew each hose's fastener and remove these hoses. Do not dispose of these hoses as they will be reused. Next, go iside of your vehcle and remove the under dash cover and then locate the heater duct. It has a number of small screws plus clips that hold it in place, remove them. The duct should then be removed. There is also a small cover over the heater core inlet/outlet pipes. It is held on with three screws, one of which is a little hard to see, remove them and take off the small cover. It may be glued in place by a tar like insulating material. The heater core is held in place by two strap clamps over it which are held on with two screws in each. Finally, Remove the screws and clamps. The heater core will now come out
Reverse the procedure to install the new heater core. Refill the coolant and check for leaks.



Read more: http://wiki.answers.com/Q/How_do_you_replace_heater_core_87_celebrity#ixzz1DncDAfbn

Feb 13, 2011 | 1984 Chevrolet Celebrity

2 Answers

Where Is thermostat located on 1994 escort 1.9 motor


On almost all cars if you follow the upper radiator hose to where it goes into the motor, that is where the termostate is.

Jan 15, 2011 | Ford Escort Cars & Trucks

1 Answer

Blower Motor Location


Look under the hood on the fire wall where the heater hoses go into the interior ogf the car. The heater core is just inside under the dash. theree is no easy way to tak out the heater core. But it is done all the time.
Do that only if it's leaking and the carpet under the dash is wet. If not, try flushing the heater core .With the engine cold and the radiator empty, Take both hoses off that connect to the heater core. Insert some hoses to both the inlet and outlet so you can direct the water down and away from the engine. With a good stream of water pressure. Put the water hose into one of the inlets. And spray the water in until it comes out the other hose. Flush out everything that may be clogging the core.

Nov 20, 2009 | 1992 Oldsmobile Custom Cruiser

1 Answer

How to replace a water pump on a 2003 yukon


Water Pump Replacement (4.8L, 5.3L and 6.0L Engines)
Removal Procedure
1. Drain the cooling system.
2. Loosen the air cleaner outlet duct clamps at these locations:
 Throttle body
 Mass Airflow/Intake Air Temperature (MAF/IAT) sensor
3. Remove the radiator inlet hose clip from the outlet duct.
4. Remove the air cleaner outlet duct.
5. If necessary, remove the engine sight shield.
6. Remove the radiator vent inlet hose from the radiator hose clips.
7. Reposition the inlet hose clamp at the water pump.
8. Remove the inlet hose from the water pump.
9. Remove the fan blade.
11. Reposition the outlet hose clamp at the water pump.
12. Remove the outlet hose from the water pump.
13. Reposition the surge tank outlet hose clamp at the water pump.
14. Remove the surge tank outlet hose from the water pump.
15. Reposition the heater inlet hose clamp at the water pump.
16. Remove the heater inlet hose from the water pump.
17. Remove the water pump bolts.
18. Remove the water pump and gaskets.
19. Discard the water pump gaskets
Installation Procedure Important: All gaskets surfaces are to be free of oil or other foreign material
during assembly.
1. Install the water pump and NEW gaskets
2. Install the water pump bolts.
3. Install the heater inlet hose to the water pump.
Zoom Sized for Print
Notice: Refer to Fastener Notice in Service and Precautions.
2.1. Tighten the bolts a first pass to 15 Nm (11 ft. lbs.).
2.2. Tighten the bolts a final pass to 30 Nm (22 ft. lbs.).
4. Position the heater inlet hose clamp at the water pump.
5. Install the surge tank outlet hose to the water pump.
6. Position the surge tank outlet hose clamp at the water pump.
7. Install the outlet hose to the water pump.
8. Position the outlet hose clamp at the water pump.
9. Install the accessory drive belt.
10. Install the fan blade.
11. Install the inlet hose to the water pump.
12. Position the inlet hose clamp at the water pump.
13. Install the engine vent inlet hose to the radiator hose clips.
14. If necessary, install the engine sight shield.
Important: Align the arrow at the throttle body end of the duct with the throttle
body attaching stud.
15. Install the air cleaner outlet duct
16. Install the radiator inlet hose clip to the outlet duct.
17. Tighten the air cleaner outlet duct clamps at these locations:
 Throttle body
 MAF/IAT sensor Tighten the clamps to 7 Nm (62 inch lbs.).
18. Fill the cooling system.

I hope this helps. The numbering is incorrect in the sequence but the instructions are correct.

Roy

Nov 06, 2009 | 2003 GMC Yukon

Not finding what you are looking for?
1995 Honda Accord Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...