Question about 2007 Peugeot 207 1.4

1 Answer

I'm searching for where i can find the fuse which controls my rear light on drivers side

Bulb seems ok as new one inserted but light still not coming on

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 689 Answers

Look for a Fuse box in the engine compartment, it might have fuse in it for the tail lights, That where the fuse for the tail lights are for my 2000 ,Hyundai Elantra,

Posted on Nov 08, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW TO REPLACE BRAKE LIGHT ON 1997 F 150 TRUCK


if only one side of brake light is out it's probally the bulb, these are easly changed , by first going to auto parts store and getting new bulb , then using phillips head screwdriver remove four screws that are around permiter of tailight that is out , carefull dont loose these screws you'll need to put them back , gently rock tailight back and forth to break gasket seal and pull light straight out of truck it comes out about 10 inches , this modle has if i remember right three bulbs in taillight it's the center one if i remember right grap the white plastic bulb holder firmly and turn 1/4 turn counterclockwise the bulb holder should come free of tail light , grab bulb with one hand and holder with other and wiggle gently sideto side till bulb pops free of holder , use a clean towel or cloth to hold new bulb and insert it back same direction as previous bulb, wipe all smuges and fingerprints off bulb (this would cause hot spot on bulb and make it fail early) reinsert holder into tail light , I use car wax as gasket renewer on tail light border before i put it back in, but thats optional reinstall all four screws back in , there you are done !!

May 13, 2014 | 2000 Oldsmobile Alero

1 Answer

Right rear break light doesnt come on


check the ground wire that is most likely the problem. also on some there is a fuse rare but sometimes there is one .

Jan 13, 2014 | 2005 Volkswagen Sharan 1.9

1 Answer

My driver side headlamp won't work even with new bulb


check for a fuse probably your car have separated fuses for every light side.

Aug 27, 2012 | 2007 Dodge Caliber SXT Sport Hatchback

1 Answer

Where is the brake lightfuse located at on my 2004 envoy xl


There is only one fuse for the brake light, so if the passenger side is working, the fuse is OK. You most likely have a bad bulb, bad bulb socket or a wire issue. The circuit board that all of the rear light are mounted to also has had problems in the past.
BTW - the fuses for the rear light are under the rear seat.

Jul 30, 2012 | 2004 GMC Envoy

1 Answer

How do i remove the driver side rear tail light assembly on a 2000 chrysler voyger


Instructions

Shift your Voyager into "Park," set the parking brake and pull the keys out of the ignition.

Open the liftgate to access the rear storage compartment.

Remove the two screws from the inboard side of the taillight housing and place them in your pocket for safekeeping.

Insert a screwdriver between the outboard side of the rear combination light assembly and the van's body, and then pry the assembly loose. Avoid scratching your van's exterior paint.

Twist the turn signal bulb socket counterclockwise to remove it from the light assembly.

Pull the bulb out of the socket and dispose of it immediately to prevent it from becoming a hazard. Then, install the new bulb in the socket.

Reinstall the socket and activate the turn signal. If it lights up, screw the cover back into place and close the liftgate

Jul 24, 2012 | Chrysler Cars & Trucks

1 Answer

Dash illuminates when key is inserted, but when turned to start position ,the car starts and drives, but you lose indicators,wipers, rear brake lights,electric windows . there is a yellow 20 amp fuse in...


It wold be the faulty SAM according to my knowledge your technician have told you what's wrong in it. must check the front SAM and rear SAM as well,

Jul 15, 2011 | 2002 Mercedes-Benz C-Class

1 Answer

I can't seem to find or how to change the blubs for the turn signals and the back up lights.


I don't have your make and model so I can only give a general answer.
  • Turn the engine off and open the hood. Pry up the two fasteners from the radiator air baffle with a flathead screwdriver. Move the baffle to the side to access the top of the headlight case.

  • 2

    Pull up the two metal rods behind the headlight case. These secure the case to the vehicle. You may need your pliers to pull them up.

  • 3

    Gently pull the headlight case out to access its rear. On the rear, you will find several black dust covers. Twist off the dust cover closest to the fender (the outward dust cover) to access the turn signal bulb.

  • 4

    Turn the bulb module counterclockwise to release it. Unplug the electrical connector from the bulb module. Connect the new bulb to the electrical connector (don't touch the glass with your hands; hold it by the plastic piece). Insert the bulb module in the turn signal housing, turn it clockwise and screw the dust cover back on.

  • 5

    Insert the headlight case in the mount. Push the pins back down to secure it. Position the radiator baffle in its place and insert the fasteners.

  • as far as back up lights,

  • Go in the trunk and pull back the side pannel of the trunk and turn the bulb until it comes out and change it and turn the new bulb back in place.

    Apr 01, 2011 | Chevrolet Blazer Cars & Trucks

    1 Answer

    How to replace brake light on 1998 ram truck 1500


    1.remove screws holding the light cover in place.
    2. Remove plug from bulb
    3. push and turn on bulb to release bulb from socket
    4. insert new bulb
    5. Plug in wire connecter
    6. insert screws holding light cover in place

    Mar 15, 2011 | 1998 Dodge Ram 1500 4WD

    Not finding what you are looking for?
    2007 Peugeot 207 1.4 Logo

    242 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Peugeot Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    mike hayward

    Level 2 Expert

    279 Answers

    Wahs Team

    Level 2 Expert

    215 Answers

    Are you a Peugeot Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...