Question about 2002 Chrysler Sebring

1 Answer

Ok i have been working on this 02 Chrysler Sebring for 2 months i have replaced so much on the car it runs a little hard and once it gets warmed up it does not want to move stalls out and wont start back it has all new hoses new spark plugs and wires both upper and lower valve cover gaskets fuel pump and fuel relay fuse and a new fuel injector wire harness i don't know what else to do please help

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 4,393 Answers

Stop throwing parts at it and hire a mechanic to at least diagnose it

Posted on Jul 29, 2017

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 40 Answers

SOURCE: 95 chrysler lebaron gtc 3.0 starts for a second and then stalls out

What is the fuel pressure reading at the fuel rail?

Posted on Mar 19, 2009

  • 101 Answers

SOURCE: chrysler wont start

Sounds like a short maybe. maybe the wire completely broke? if you know a technician, see if the fuel pump is even getting power when key is on

Posted on Jul 02, 2009

  • 1 Answer

SOURCE: 1999 Chrsler Sebring LXi v6 2.5L. Car dies.

I had the same problem with my 1999 Chrysler Sebring 2.5L V6 Convertable. It started stalling at intersections; would lose RPMs' and die while driving it; and would not start unless it sat for a few minutes. Once it started, you'd have the scenario start all over again...

I hadn't kept up my maintenance schedule like I usually do, so I did the usual; I replaced my spark plugs and wires, changed the oil and filters, ect...

Finally, after it doing the same thing and wasting a ton of time and frustration on the side of the road, I took it to a mechanic that put it on his $9,000 diagnostic machine. The verdict; CRANK SHAFT POSITION SENSOR!

The Haynes Manual will tell you wrong on its location for the 1999 Lxi 2.5L V6 convertable; it is NOT LOCATED BEHIND THE BATTERY TRAY. The crankshaft position sensor is actually located about 4 to 6 inches below the distributor, which is about dead center of the motor, on the transaxle housing.

You do have to take off the tire and the skirt cover to get to it. I had to purchase two long socket extensions just to get to the bolt that mounts the sensor to the transaxle housing; but it was well worth the 20 bucks...

All in all, it took me three hours to find the damn thing, and then to figure out what I needed to take the old one off and get the new one installed.

The $65 dollars that I spent to find out what the problem was is worth it....

Now, the car runs better than ever....

Posted on Oct 30, 2009

  • 244 Answers

SOURCE: 2001 pt cruiser wont start after changing the cam

l like keepin it simple and say check all grounds clean n tight and engine fuse box is dry and clean.

Posted on Apr 25, 2010

ZJLimited
  • 17970 Answers

SOURCE: 1999 Chrysler Sebring Convertible code P1495. I

Code 1495 = Leak Detection Pump Solenoid Circuit

Remove the connector from the solenoid (should be on the back wall, just to the drivers side of the air-hat). You will have the solenoid to check and the harness. What you want to measure is the voltage coming from the harness and the resistance of the solenoid.

Turn the key to the "ON" position but do not start the motor; the voltage at the connector should be at least 10V or more,.now, check the resistance of the solenoid (should be around 35 ohms).

Hope helps.

Posted on Jun 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

02 chrysler sebring 2.4, hard to no start and rough idle


Complete turn up to include fuel and air filters. Then check to see how it starts. If still problem, let us know what the problems are.

Nov 26, 2016 | 2002 Chrysler Sebring

1 Answer

Runs rough when it's warm. comes and goes. has a 2.7. and then a 99 dodge carvan with a 3.3 does the same thing.


Chrysler Sebring Questions - Car running very rough ...

www.cargurus.com > Questions > Chrysler > Sebring

CarGurusMar 27, 2011 - It seems after car gets to a certain temperature it runs very rough. ... 2011 at 12:16 PM about the 1998 Chrysler Sebring 2 Dr LXi Coupe ... it.one day it washot out and it was running sluggish with rough idle.and ... I changed the altnator and battery its runs like its brand-new.now ... 2002 Chrysler Sebring LXi.

Chrysler Sebring Questions - Engine Power Loss After Car ...

www.cargurus.com > Questions > Chrysler > Sebring

CarGurusNov 3, 2011 - Engine Power Loss After Car Is Warmed Up - Major loss of power after car has ... When vehicle is cold runs ok, sometimes a little rough but not bad. Full power. Allowed vehicle to run for over 45 minutes last night at idle, died on its own, car sat approximately 20-30 minutes. ... 2002 Chrysler Sebring LX.

* Chrysler Sebring/200 Convertible Club * • View topic - Rough ...

www.sebringclub.net/board/viewtopic.php?p=69097

Dec 29, 2006 - 5 posts - ‎3 authors
However, the vehicle still suffers from rough idle under certain conditions: ... been resolved (I don't think he noticed that it happened only when warm though). .... The test will tell you its general condition without having to dig it out of the fender, ..... Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group rough ...
15 posts
May 24, 2010
Low idle rpm
15 posts
Mar 8, 2007
More results from www.sebringclub.net

Jan 01, 2016 | 2002 Chrysler Sebring

1 Answer

When cold runs with a miss


Have you replaced the spark plugs since this started? A friend of mine had a similar problem and after months of dealer warranty work, they found it was a cracked spark plug insulator that caused numerous erroneous error codes in the computer.

Good luck,
Jim

Aug 19, 2012 | 1999 Chrysler Sebring

3 Answers

2004 Chrysler Sebring Convertible How do I change the water pump


It is not all that hard, you can do it just get a haynes manual or any manual it will be very helpful and it away great to look at it when you doing the work. Have fun

May 11, 2009 | 2004 Chrysler Sebring

1 Answer

Heater fan only works on high speed


usually when the blower motor gets old its starts to draw more current to run. which can pop fuses, burn out resistors and melt wires. also when you go to replace the resistor check the connector for signs of melting or burning you may end up having to replace that conector

Jan 06, 2009 | 1999 Chrysler Sebring

Not finding what you are looking for?
2002 Chrysler Sebring Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...