Question about Cars & Trucks

Open Question

Jaguar x type dtc p1582 - Cars & Trucks

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

TDISLine
  • 1874 Answers

SOURCE: Get DTC P1582 which is

DTC code EOBD type: P1582 - Idle speed adaptation - limit reached.
Probable cause: Intake / exhaust leaks, air system, fuel pressure / pump, injector(s), EVAP canister purge valve.

1. Check intake system for leaks: Spray some carb cleaner product around intake manifold area, engine idling. If engine idle speed revs up there are intake leaks. If engine idle speed doesn't change the intake system is OK.
2. Check exhaust system for leaks: Inspect entire exhaust line for black tracks of soot. If you will find something bad repair & replace damaged pieces.
3. Fuel pressure checking:
3.1. Ensure ignition switched OFF.
3.2. Connect pressure gauge between fuel supply pipe and fuel rail.
3.3. Open gauge tap. See picture below:

tdisline_186.jpg
3.4. Start engine. Allow to idle.

Posted on Jan 24, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2003 S-type jaguar that goes into a limp mode and stops running then the engine system fault shows ,the parkbrake fault and DSC not available also shows. Diagnostic showed codes PO121,P1582??


code p 0121 is associated with the throttle position sensor and accelerator position sensor
causes are from cable adjustment --throttle position and accelerator position sensors
code p0533 refers to ac refrigerant pressure sensor--high input== causes --ac pressure too high (cooling fault -condenser fan not running at radiator-- too much gas --pressure sensor
p 0105 refers to map sensor / barometric pressure sensor --circuit malfunction===causes wiring--- map sensor --baro sensor ECM
code p0566 refers to cruise control master switch== causes --control switch , ---ECM
code p1582 refers to electronic throttle monitor data available which will be associated with the p 0121 code and faults

Jan 08, 2017 | Jaguar Cars & Trucks

1 Answer

What is fault codes P1582


Type: OBD P1582

That is how you look up codes

Aug 05, 2014 | 2002 Volkswagen Cabrio

1 Answer

2002 jaguar x type code P1000


DTC 1000 indicates the OBD II monitor test/drive cycle is not complete and the probable cause is low battery voltage.

Apr 25, 2014 | 2004 Jaguar X-Type

1 Answer

P1582 jaguar s type


the 1582 code is a flight recorder code meaning that at some point one of the following has happened: the inertia switch has been triggered,throttle body signal has triggered the limp mode,the engine starts but stumble and then shuts off,or engine fail to start,or a engine stall has occured.This is what causes this code.If the issue was resolved,clear the code becuae it can become permanent and although the car will run fine the code will be there without a mil showing.

Mar 21, 2014 | 2003 Jaguar S-Type

1 Answer

Jaguar codes p1582


P1582 is special in some way. You don't need to clear it any time soon (or, I suppose, at all). As the wording shows, it's about data being logged not a fault. (But a fault will have led to the storing.)

Aug 12, 2013 | Cars & Trucks

1 Answer

Jaguar xtype code p1582 how to remove


P1582 - EDR (Engine data recorder) can not be remove with a reader has to be taken to the dealer.

Feb 03, 2013 | 2003 Jaguar X-Type

1 Answer

P0354 Ignition Coil D Primary/Secondary Circuit Malfunction This is what the scantool came up with on my 2001 Jaguar s-type 3.0 Car has been idling funny but will get cruising on the highway.


this code is saying you have a failing ignition coil..You will have to swap them and determine which one is failing...here is the procedure.. DTC P0354; RANDOM MISFIRE DETECTED, MISFIRE DETECTED, (CYLINDERS 1-8) IGNITION COIL PRIMARY CIRCUIT MALFUNCTION, (CYLINDERS 1-8)

G290076t1 : CHECK COIL FUNCTION BY SUBSTITUTION
  1. Swap the suspect coil for a known good unit.
  2. CLEAR the DTC. TEST the system for normal operation.
- Does the same DTC reoccur? The DTC will indicate if the same cylinder is misfiring. -> Yes
INSTALL a new coil. CLEAR the DTC. TEST the system for normal operation.

-> No

G290076t2 : CHECK THE IGNITION COIL SUPPLY VOLTAGE CIRCUIT
  1. Disconnect the relevant ignition coil electrical connector(s), (PI02 to PI09).
  2. Turn the ignition switch to the ON position.
  3. Make sure the ignition relay is energised.
  4. Measure the voltage between:
- Is the resistance greater than 5 ohms? -> Yes
REPAIR the high resistance circuit. CLEAR the DTCs. TEST the system for normal operation.

Sep 19, 2011 | 2001 Jaguar S-Type

1 Answer

My s type jaguar dtc p1638 i dont undarstand the mining of that why, 2000 year it asking me to look in the manual tecnical book


Fault codes are listed in the technical handbook, no good to you as it's a Jaguar service item unless you can get a copy of JTIS from ebay etc.


Fault Code:- P1638 Indicates a Power-train fault


The fault is generally due to a problem in the Computer & Output Circuit area


Fault Description: CAN ECM / INST network malfunction

Action of ECM:- none


After clearing the DTC, complete the Ignition ON 10 seconds
Check for a reoccurrence of fault DTC.


Possible Fault:- CAN open circuit fault - INST to ECM CAN short circuit fault INST failure ECM failure D

May 26, 2011 | 2003 Jaguar X-Type

1 Answer

Flight recorder data is stored.electronic throttle monitor data availabe code p1582


1 Inertia switch activated

2 Throttle Limp Home mode

3 Engine starts and stumbles

4 Engine fail to start
5 Engine stall

If none of the five conditions occur, check: Inertia switch to ECM circuit:

short circuit to B+ voltage Inertia switch failure

You can check the Inertia switch status on the Instrument cluster Diagnosis, see http://www.bluejag.co.uk

Jan 30, 2011 | 2002 Jaguar X-Type

2 Answers

WON'T PASS EMISSIONS


DIAGNOSTIC TROUBLE CODE (P1582 TO P1613) DTC, DTC text, Corrective action. SAE, VAG, P1582, 17990, Idle Adaptation at Limit.

Check intake for leaks, and or loose vaccum hoses.

Sep 17, 2009 | 1998 Volkswagen Jetta

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

294 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...