Question about Peugeot Cars & Trucks

Open Question

Peugeot 307 heater air distribution control broken

Knob turns but nothing happens

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: peugeot 307 heater blower fault

Hi
i just had the same fault, but being in the trade it is normally only 1 of 2 problems.
the heater resitor packing up or the wiring loom.
both can be bought through peugeot.
try the heater resistor first (£40). to find it undo 7 star screws to remove glove box then look in behind centre conlsole near back of radio diconnect the black plug with a red and black cable. twist back of fan motor clockwise and remove fan(it's a bit of a tight squeeze to remove),then put your hand inside the hole you just made till you feel the flat resistor turn this anti-clockwise and disconnect green plug then reassemble as removed,

if this does not fix it then it is the loom, to remove this it is best to follow the wires from the back of fan motor up to where i think if i remember lead to 2 other plugs 1 green and 1 black on the way to another green plug up behind the drivers foot well, then thread the new loom back the same way.

on the 405 i think the resistor is in behind the fan motor accessed throgh the driver side footwell again you need to first take out the fan motor normally twisted anti-clockwise. it is un common for 405 to burn out heat resistors it is normally down to a wire fault.

hope this helps

Posted on Jan 18, 2009

Ad
  • 205 Answers

SOURCE: "when do i change the cam belt on a peugeot 307 sw diesel"

usually you should do it for peugeot diesel at 122000 miles along with water pump and the tensioner roller that runs under the cambelt too. But to be on the safe side do it at 100000 and save the fortune.
It took me (DIY job) about 6-8 hours as i wanted to save 450 pounds.

Posted on Sep 04, 2009

  • 6 Answers

SOURCE: 2000 gmc sierra 1500 5.3 v8. a/c heater control problem

your heat/cool and vent selection options are controlled by engine vacuum through small clear tubes attached to the rear of your climate control interface. Other vehicles have small steel pull wires that operate the desired changes. You might try removing the trim and any fasteners affiliated with the interface/console. GENTLY pull outward and look to see if any of these tubes are pulled off or cut/damaged. Did anyone recently install a new stereo in the vehicle? If so, the vacuum tubing and or pull wires that change your outlets could have been damaged when the stereo unit was pushed into place. Hope this helps

Posted on Sep 09, 2009

Testimonial: "Very good information. THANKS!"

  • 583 Answers

SOURCE: Peugeot 307 diesel 307 - Unblock diesel filter

if it says the diesel filter, then that is what it means,a fuel filter.normal service requirement on any vehicle and can be done for small dollars at any garage

Posted on Dec 04, 2009

  • 6 Answers

SOURCE: peugeot 307 1.6

peugeot and citreon cars do bite high generaly, it is hydaulic there is no adjustment. but it also depends on how high it is ?? does it slip if you slightly rest your foot on whilst driving?? they do have a problem with the bearings going through the cover as it is the same bearing as a HDI . but you woud notice this as a different problem. ie noise or vibration on pedal. call me for more info .. paul @ the clutch centre..01527 64440 07790438337

Posted on Mar 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My heater on my peugeot 307 doesn't demist windows but the heater and everything els work


I'm guessing that no air blows out of the upper vents when you select the demist setting? There are numerous flaps in the air conditioning systems on automobiles that move to control where air flows. Chances are one of those has either failed or the actuator has broken. Depending on your level of skill you may be able to rig the doors into the correct position without removing the dash. A complete repair will probably involve removing the dashboard and replacing the failed component.

Feb 06, 2016 | Peugeot Cars & Trucks

1 Answer

How do I fix the air condition control buttons?


Hello,

Well, I can't tell by your explanation if the knob stem is broken & just spinning around or if it feels normal and nothing happens.

So, I guess I would first have you check all the fuses labeled "AC" or "Heater". Might be just a blown fuse, but remember, fuses always blow for a reason. There are many things that can be causing your problem like the heater/ac fan speed relay or a broken wire, etc.


I don't how auto repair savvy you are but, Google "Mazda 3 a/c panel". You will see many things on that first page like inexpensive replacement knobs, etc. There are even several YouTube videos on how to gain access to your ac/heater control panel. There is a wealth of information there. If you are not a do-it-yourselfer, you can at least look through there to educate yourself before you take your car to someone. Being informed ahead of time is very valuable.

Bestalucktoyou,
M

Nov 28, 2014 | 2006 Mazda 3

1 Answer

Air Distribution Knob Broken


I think the air distribution knobs are all the same and can be removed by just pulling them. What I suggest is to interchange 2 knobs and turn them. If the problem follows the knob, look inside and see if it's stripped or cracked. If the problem stays at the original position, then you may have a defective switch. Let me know if this helps!

Jan 17, 2014 | 2003 Pontiac Vibe

1 Answer

Headlights on my 307 come on after car is locked


faulty relay i suspect here try swopping them around under the bonnet in the power distribution box if i remember rightly .failing which renew the stalk control switch ,the return spring inside the switch could be weak ,often happens same as the peugeot

Jan 27, 2013 | 2001 Peugeot 307

2 Answers

PEUGEOT 307 FUSE KEEPS BLOWING (abs faults, horn doesnt work)


i have a peugeot 307 number 8 fuse keeps blowing so i have to keep changing the 20 amp fuse please help me i am trying to find out what is causing this

Dec 07, 2012 | 2002 Peugeot 307

1 Answer

Interior blower only blows up to warm on 1997 A4 2.7ltr


Check the blend door cable for proper attachment to the control panel and to the blend door. Try opening the door manually to see the you can get hot air out. If not, the door may be broken inside the heater box. If yes, correct/adjust the cable attachment for proper operation.

REMOVAL & INSTALLATION
1990-97 Passat Models
Install the cable ends marked with a white or blue band to the control head assembly. The cables must be attached to the control head before connection to the system air flaps.
  1. Remove the climate control head from the center dash assembly to access the control head cable ends.
  2. Remove the lower dash panels as necessary to access the cable lever arms.
  3. Attach the airflow distribution cable (cable 2) to the airflow distribution knob's lower control lever.

This cable can be identified as follows:
Operates the mode/central air flap Cable has a black sleeve and is 25.0 inches (634 mm) long Cable is marked with a white band
  1. Press the cable's sleeve against the control head stop and install the retaining clip.
  2. Attach the temperature control/air blend cable (cable 3) to the air temperature knob's control lever.

This cable can be identified as follows:

Operates the temperature control/air blend cable air flap Cable has a blue sleeve and is 21.0 inches (535 mm) long Cable is marked with a white band
  1. Press the cable's sleeve against the control head stop and install the retaining clip.
  2. Attach the airflow distribution cable (cable 1) to the airflow distribution knob's upper control lever.

This cable can be identified as follows:


Operates the footwell/defroster air flap Cable has a black sleeve and is 37.5 inches (954 mm) long Cable is marked with a blue band
  1. Install the cable such that the blue band is over the retaining clip mount and install the retaining clip directly over the blue band.
  2. Install the climate control head.
  3. Set the air flow distribution knob to defrost.
  4. Connect the longest airflow cable (cable 1) to the footwell/defroster flap lever on the heater's air box.
  5. Press and hold the flap's lever toward the retaining clamp perch and install the cable retaining clip.
  6. Set the airflow distribution knob to the Vent position.
  7. Connect the short airflow cable (cable 2) to the central/mode flap's lever.
  8. Pull and hold the mode flap's lever away from the retaining clamp perch and install the cable retaining clip. Check the operation of both air flaps making sure they can be heard contacting their stops.
  9. Set the temperature control knob to full cold.
  10. Connect the blue-sleeved cable (cable 3) to the air blend/temperature flap's lever.
  11. Pull and hold the mode flap's lever away from the retaining clamp perch and install the cable retaining clip. Check the operation of the air blend/temperature flap making sure it can be heard contacting the stops.

11_24_2011_10_52_22_pm.gif

Fig. Side view of the control head and cable location. 1. Footwell/defrost flap cable-2. Air distribution cable-3. Temperature control flap cable

11_24_2011_10_53_58_pm.gif

Fig. Temperature flap cable location and adjustment

Nov 24, 2011 | 1998 Audi A4

1 Answer

I have a 93 Saab and my vents aren't blowing heat. When I hit a bump in the road it may kick my heat on full blast for a couple of minutes, but as soon as I hit another bump, the heat kicks off. Also, the...


You don't say whether the fan starts and shuts off with the bumps, or the heat goes cold but the fan stays on. If it's the fan shutting off and coming back, you most likely have an intermittent connection to the blower motor somewhere at the fuse box, the fan speed control switch or the fan motor, or a loose ground connection at the fan motor. The fan motor is visible under the right side speaker grille on the dash. Make sure you re-connect the short black corrugated hose to the grill vent or you won't have defrosting on that side!

The air distribution rotary switch controls where the air goes. The fan speed switch controls exactly that: fan speed. the temp rotary switch controls the coolant temp into the heater core. You need to clarify what you mean by "Also, the dash controls for the vents won't allow me to turn up the power"

You might also have one or more of the following issues:
  1. is you vacuum tank properly connected and are there no leaks in the vacuum piping? The tank is in the driver side rear wheel well below the trunk deck on a convertible, and in the passenger side front fender area on the other cars. It's a white bottle with one or two hoses connected to it. If not properly on, your vacuum operated heater flaps won't move. Does the air distribution knob make sucking or hissing noises when you set it to different positions? If not, check the tank connections, look for vacuum line leaks, then suspect the vacuum valve behind the distribution knob.
  2. if the air distribution rotary switch makes noises when you change its setting, but nothing happens, then suspect the vacuum solenoids that open and close the heater flaps - could be a loose vacuum line or a defective vacuum solenoid
  3. the shaft connecting the temp control knob to the heater valve behind it may not be properly in place. This can be inspected, and adjusted if necessary, from the left side speaker/vent cutout on top of the dash. Make sure you re-connect the black flex hose to the air vent tube, or you'll get no defrosting afterwards!
  4. remember, the centre vents always blow cold air; a brilliant idea from Saab so the driver (and passenger) can get fresh air in the face and stay awake while the rest of the driver, passenger and car is toasty!

Oct 26, 2009 | 1993 Saab 900

1 Answer

No fans,no hot air ,no cold air


Read the owner's manual! The fuses are all listed in there..
Its just as possible that its an ecu fault or multiplug connector at fault, or the blower motor. Im afraid 307s of this era are notorious for electrical faults...

Jan 23, 2009 | 2005 Peugeot 405

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

mike hayward

Level 2 Expert

279 Answers

lloyd cole

Level 2 Expert

250 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...