Question about Cars & Trucks

1 Answer

Hi i have corolla 03 the fuel hose connected to the fuel filter under the back seat keep pop out its place. Is the pipes blocked?? or Too much pressure??? please help Thx

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 156 Answers

It;s not threaded ? Is it clamped ? Try a screw clamp or possibly a semi plugged fuel filter

Posted on Nov 08, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

98 corolla problem pumping gas were is vent tube


The vent pipe is connected to a filter under the hood, Remove the pipe from the filter, if it solves the problem, replace the filter. Also, check for blockage or if the pipe is not blocked.


http://ww2.justanswer.com/uploads/tyroneboman/2011-11-12_040259_1999_toyota_corolla.pdf

Nov 10, 2015 | Cars & Trucks

1 Answer

Where are the two fuel filters located on a Toyota corolla 2000?


easy to figure out with out knowing. jack up the car and look under the car and look. some have the fuel filter under the back seat location. others are in the engine compartment. you will need to follow the hoses or tubing and look for larger can that hose 2 or 3 hoses going to and out. most have 1 in and 1 out and bolts or nuts holding the lines in place. before removing the hoses. please take this step. pull the fuel pump relay and then try starting the car. it will run or not run for a second or two. this will take the pressure off the system and save you getting sprayed with raw fuel.

Mar 03, 2015 | 2000 Toyota Corolla

2 Answers

Where it the fuel filter on a 2005 Toyota corolla.


Hi,
The fuel filter for your Corolla is in the fuel tank. with the fuel pump.
No external filter.
Wayne

Aug 07, 2011 | 2005 Toyota Corolla

2 Answers

I have a 97 ford taurus and its a clunker. Im getting rid of it. It got a full tank and i would like to siphon it out and into my new car. I got a siphon kit and fed the tub all the way in till i wouldnt...


unfortunately most fuel tanks are made so you can no longer siphon gas through the fill tube. if you want the fuel that badly you could disconnect the fuel line from the fuel filter and wait for it to drip out.

Mar 31, 2011 | 1997 Ford Taurus

1 Answer

How to change the fuel filter


Fuel Filter The filter should be inspected for external damage and/or leakage at least once a year. The fuel filter should be changed only as necessary. Toyota Motor Corporation recommends replacing the carbureted fuel filters at 15,000 miles and 30,000 miles on fuel injected models. NOTE: Fuel lines and connections, fuel tank vapor vent system hoses and fuel tank bands should be inspected every 60,000 miles or every 36 months. The fuel tank cap gasket should be replaced 60,000 miles or every 72 months.
---
REMOVAL & INSTALLATION Carbureted Engines The fuel filter on carbureted engines is a plastic cylinder with two ports for the fuel. It is usually located in the engine compartment near the charcoal canister.
  1. Using a pair of pliers, expand the hose clamp on one side of the filter, and slide the clamp further down the hose, past the point to which the filter pipe extends. Remove the other clamp in the same manner. Grasp the clamps and slide them up the hose slightly above the filter ends 88271p10.jpg

  2. Grasp the hoses near the ends and twist them gently to pull them free from the filter pipe. Slide the hose off the end of the fuel filter end 88271p11.jpg

  3. Pull the filter from the clip and discard. Be carefull when removing the filter, some fuel may spill out if not held upright 88271p12.jpg
    To install:
  4. Install the new filter into the clip. The arrow must point towards the hose that runs to the carburetor.
  5. Push the hoses onto the filter pipes, then slide the clamps back into position.
  6. Start the engine and check for leaks.
Fuel Injected Engines 1993-97 MODELS
  1. Turn the ignition switch to the LOCK position. Disconnect the negative battery cable and wait at least 90 seconds before proceeding with working on the fuel system. This will depressureize the fuel system. The fuel filter can be hard to locate on these engines 88271pa1.jpg
    Fig. 4: Exploded view of the fuel filter mounting - 1993-97 models 88271g02.gif
    Fig. 5: Disconnect the negative battery cable prior to all fuel system repairs 88271g03.gif
    CAUTION
    Failure to depressurise the fuel system could cause personal injury.
  2. Disconnect the Intake Air Temperature (IAT) sensor wiring.
  3. Loosen the air cleaner hose clamp bolt, the disconnect the four air cleaner cap clips. Fig. 6: Loosen the air cleaner hose clamp bolt 88271g04.gif

  4. Spearate the air cleaner hose from the throttle body, and remove the air cleaner cap together with the air cleaner hose.
  5. Disconnect the EVAP canister hose from the charcoal canister. Fig. 7: Remove both EVAP hoses from the charcoal canister 88271g05.gif

  6. Remove the charcoal canister from the bracket.
  7. Place a suitable container or shop towel under the fuel filter. Remove the union bolt and two gaskets, then slowly disconnect the fuel inlet hose from the fuel filter outlet. Fig. 8: Remove the union bolt and two gaskets from the fuel filter, then disconnect the inlet hose from the filter 88271g06.gif

  8. Using a special wrench 09631-22020 or equivalent, disconnect the inlet pipe from the fuel filter. Remove the two bolts and the filter from the vehicle. Fig. 9: Using a special tool, disconnect the inlet pipe from the fuel filter 88271g07.gif
    Fig. 10: Remove the two filter mounting bolts, then separate the filter from the vehicle 88271g08.gif
    To install:
  9. Install the fuel filter with the two bolts and tighten them to 43 inch lbs. (5 Nm).
  10. Using the special wrench 09631-22020 or equivalent, connect the inlet pipe to the fuel filter. Tighten to 22 ft. lbs. (30 Nm). Using a torque wrench, tighten with a fulcrum length of 11.81 inch (30cm). Install the fuel inlet hose to the filter outlet using new gaskets and union bolt. Tighten to 22 ft. lbs. 30 Nm). Fig. 11: Install the filter inlet hose to the filter outlet, then tighten to 22 ft. lbs. (29 Nm) 88271g09.gif

  11. Install the charcoal canister to the bracket. Connect the two EVAP hoses to the canister.
  12. Connect the air cleaner hose to the throttle body. Install the air cleaner cap together with the air cleaner hose.
  13. Attach the IAT sensor wiring.
  14. Connect the negative battery cable. Start the engine and check for leaks. Reset any various digital equipment such as radio memory and the clock if necessary.
prev.gif next.gif

Nov 08, 2010 | 1993 Toyota Corolla

1 Answer

Where is the fuel pump located in a 1990 geo prizm? Is it in the fuel tank or on the fuel line?


Electric Fuel Pump REMOVAL & INSTALLATION The electric fuel pump used on fuel injected Nova and Prizm cars is contained within the fuel tank. On 1988–92 models it cannot be removed without removing the tank from the car. NOTE: Before removing fuel system parts, clean them with a spray-type engine cleaner. Follow the instructions on the cleaner. Do not soak fuel system parts in liquid cleaning solvent. CAUTION
The fuel injection system is under pressure. Refer to the procedure above and release pressure slowly and contain spillage. Observe no smoking/no open flame precautions. Have a Class B-C (dry powder) fire extinguisher within arm's reach at all times. 1988–92
  1. Release the fuel system pressure as outlined earlier.
  2. Using a siphon or pump, drain the fuel from the tank and store it in a proper metal container with a tight cap.
  3. Remove the rear seat cushion to gain access to the electrical wiring.
  4. Disconnect the fuel pump and sending unit wiring at the connector.
  5. Raise the vehicle and safely support it on jackstands.
  6. Loosen the clamp and remove the filler neck and overflow pipe from the tank.
  7. Remove the supply hose from the tank. Wrap a rag around the fitting to collect escaping fuel. Disconnect the breather hose from the tank, again using a rag to control spillage.
  8. Cover or plug the end of each disconnected line to keep dirt out and fuel in.
  9. Support the fuel tank with a floor jack or transmission jack. Use a broad piece of wood to distribute the load. Be careful not to deform the bottom of the tank.
  10. Remove the fuel tank support strap bolts.
  11. Swing the straps away from the tank and lower the jack. Balance the tank with your other hand or have a helper assist you. The tank is bulky and may have some fuel left in it. If its balance changes suddenly, the tank may fall.
  12. Remove the fuel filler pipe extension, the breather pipe assembly and the sending unit assembly. Keep these items in a clean, protected area away from the car.
  13. To remove the electric fuel pump:
    1. Disconnect the 2 pump-to-harness wires.
    2. Loosen the pump outlet hose clamp at the bracket pipe.
    3. Remove the pump from the bracket and the outlet hose from the bracket pipe.
    4. Separate the outlet hose and the filter from the pump.
  14. While the tank is out and disassembled, inspect it for any signs of rust, leakage or metal damage. If any problem is found, replace the tank. Clean the inside of the tank with water and a light detergent and rinse the tank thoroughly several times.
  15. Inspect all of the lines, hoses and fittings for any sign of corrosion, wear or damage to the surfaces. Check the pump outlet hose and the filter for restrictions. To install:
  16. When reassembling, ALWAYS replace the sealing gaskets with new ones. Also replace any rubber parts showing any sign of deterioration.
  17. Assemble the outlet hose and filter onto the pump; then attach the pump to the bracket.
  18. Connect the outlet hose clamp to the bracket pipe and connect the pump wiring to the harness wire.
  19. Install the fuel pump and bracket assembly onto the tank.
  20. Install the sending unit assembly.
  21. Connect the breather pipe assembly and the filler pipe extension. NOTE: Tighten the breather pipe screw to 17 inch lbs. and all other attaching screws to 30 inch lbs.
  22. Place the fuel tank on the jack and elevate it into place within the car. Attach the straps and install the strap bolts, tightening them to 29 ft. lbs.
  23. Connect the breather hose to the tank pipe, the return hose to the tank pipe and the supply hose to its tank pipe. tighten the supply hose fitting to 21 ft. lbs.
  24. Connect the filler neck and overflow pipe to the tank. Make sure the clamps are properly seated and secure.
  25. Lower the vehicle to the ground.
  26. Connect the pump and sending unit electrical connectors to the harness.
  27. Install the rear seat cushion.
  28. Using a funnel, pour the fuel that was drained from its container into the fuel filler.
  29. Install the fuel filler cap.
  30. Start the engine and check carefully for any sign of leakage around the tank and lines. Fig. 1: Fuel tank components — 1988 VIN Code 5 engine (Nova) 84225048.gif
    Fig. 2: Fuel tank components — 1989–92 84225049.gif

Aug 14, 2010 | 1990 Geo Prizm

1 Answer

1993 toyota corolla how to replace watwr pump


  1. Place the water pump gasket (O-ring) on the block and install the pump. Tighten the mounting bolts evenly to 11 ft. lbs. (15 Nm). Install the timing belt covers, making sure they are properly seated and not rubbing on the belt or other moving parts. Install a new seal (O-ring) on the dipstick tube and lightly coat it with engine oil. Remove the plug and install the dipstick tube and dipstick; secure the mounting bolt to 82 inch lbs. (9 Nm).
Using a new O-ring, install the inlet pipe to the water pump.
Attach the clamps and bolts to hold the pipe in place and tighten to 7-9 ft. lbs. (9-12 Nm).
Connect the water inlet and water bypass hoses to the inlet pipe.
Install the water pump pulley and temporarily tighten the four pulley bolts.
Install the drive belts on all the pulleys and adjust all of them to the correct tension.
With the belts in place and adjusted, the water pump pulley will now resist turning. Tighten the pulley bolts to 16-18 ft. lbs. (22-24 Nm).
Install the front engine mount (mounting insulator).
Confirm that the draincocks are closed on the engine block and radiator. Refill the engine with coolant. Reconnect the negative battery cable. Start the engine and check for leaks.

Jul 20, 2010 | 1993 Toyota Corolla

1 Answer

How to Change a Fuel Pump on an 2005 Envoy XLT? Must drop the tank? Does it have access under the rear seat?


Usually there is no access under the rear seat for safety reasons.prev.gif next.gif Fuel Tank Removal & Installation 2002-2004 To Remove:
  1. Relieve the pressure in the fuel system.
  2. Lift the vehicle.
  3. Remove the frame brace from the frame.
  4. Remove the fuel tank shield from the fuel tank.
  5. Drain the fuel from the tank into an approved container.
  6. Loosen the fuel hose clamp and disconnect the hose from the fuel tank.
  7. Disconnect the evaporative emission (EVAP) vent valve and fuel tank pressure sensor connectors. Evaporative emission cansister pipes removal and installation gm-05-00-1546.gif

  8. Disconnect the evaporative emission (EVAP) vapor and vent valve pipes from the evaporative emission (EVAP) canister.
  9. Disconnect the fuel return and feed pipes from the fuel tank.
  10. To avoid system contamination, cap the evaporative emission (EVAP) and fuel pipes.
  11. Use a jack to support the fuel tank. Fuel tank removal and installation gm-05-00-1547.gif

  12. Detach the fuel tank straps from the frame.
  13. Lower the fuel tank.
  14. Disconnect the fuel sender connector.
  15. Remove the fuel tank from the vehicle.
To Install:
  1. Place the fuel tank under the vehicle.
  2. Connect the fuel sender connector.
  3. Attach the fuel tank straps to the frame. Torque the bolts to 24 ft-lb (32 Nm).
  4. Remove the caps from the evaporative emission (EVAP) and fuel pipes.
  5. Connect the evaporative emission (EVAP) vapor and vent valve pipes to the evaporative emission (EVAP) canister.
  6. Connect the evaporative emission (EVAP) vent valve and fuel tank pressure sensor connectors.
  7. Connect the fuel hose to the fuel tank. Torque the clamp to 22 in-lb (2.5 Nm).
  8. Connect the fuel return and feed pipes to the fuel tank.
  9. Lower the vehicle.
  10. Refill the fuel tank.
  11. Turn on the ignition for 2 seconds, with the engine off, and then turn off the ignition. After 10 seconds, turn the ignition back on with the engine off.
  12. Lift the vehicle.
  13. Check for leaks in the fuel lines.
  14. Install the fuel tank shield onto the fuel tank.
  15. Install the frame brace onto the frame.
  16. Lower the vehicle.
2005-2007 To Remove:
  1. Relieve the pressure in the fuel system.
  2. Lift the vehicle.
  3. Remove the frame brace from the frame.
  4. Remove the fuel tank shield from the fuel tank.
  5. Drain the fuel from the tank into an approved container. Evaporative emission cansister pipes removal and installation gm-05-00-1544.gif

  6. Disconnect the evaporative emission (EVAP) canister fresh air, solenoid, and purge pipes from the evaporative emission (EVAP) canister.
  7. Disconnect the fuel filler pipe recirculation hose from the fuel tank.
  8. Loosen the fuel fill pipe clamp and disconnect the pipe from the fuel tank.
  9. Disconnect the fuel feed and evaporative emission (EVAP) pipes from the fuel tank.
  10. To avoid system contamination, cap the pipes.
  11. Use a jack to support the fuel tank. Fuel tank removal and installation gm-05-00-1545.gif

  12. Detach the fuel tank straps from the frame.
  13. Lower the fuel tank.
  14. Disconnect the evaporative emission (EVAP) vent valve, fuel tank pressure sensor, and fuel sender connectors.
  15. Remove the fuel tank from the vehicle.
To Install:
  1. Place the fuel tank under the vehicle.
  2. Connect the evaporative emission (EVAP) vent valve, fuel tank pressure sensor, and fuel sender connectors.
  3. Lift the fuel tank.
  4. Attach the fuel tank straps to the frame. Torque the screws to 24 ft-lb (32 Nm).
  5. Remove the caps from the pipes.
  6. Connect the fuel feed and evaporative emission (EVAP) pipes to the fuel tank.
  7. Connect the fuel fill pipe to the fuel tank. Torque the clamp to 22 in-lb (2.5 Nm).
  8. Connect the fuel filler pipe recirculation hose to the fuel tank.
  9. Connect the evaporative emission (EVAP) canister fresh air, solenoid, and purge pipes to the evaporative emission (EVAP) canister.
  10. Lower the vehicle.
  11. Refill the fuel tank.
  12. Turn on the ignition for 2 seconds, with the engine off, and then turn off the ignition. After 10 seconds, turn the ignition back on with the engine off.
  13. Lift the vehicle.
  14. Check for leaks in the fuel lines.
  15. Install the fuel tank shield onto the fuel tank.
  16. Install the frame brace onto the frame.
  17. Lower the vehicle.

Jul 11, 2010 | 2005 GMC Envoy Xl

1 Answer

2005 Toyota Corolla Verso 2.0 d4d. Fuel filter change


my toyota corolla d4d 2.0 fuel filter light keeps coming on. when this happens it is my understanding that
the car may not start, it does not pick up speed and there could be a leakage of fuel. but none of this is happening everything seems fine

Feb 24, 2009 | 2005 Toyota Corolla

3 Answers

Fuel filter for a toyota corolla


Follow the gasoline fuel line from the engine to the bottom of your car, either at right side or left side .

Usually the fuel filter is underneath the driver side, the manufacture use ¼” or 5/16” rubber hose to connect to the metal pipe.

When you change the fuel filter, shot off the engine. Watch out the gasoline get into your eyes.

Good luck

Jul 06, 2008 | 1996 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...