Question about Cars & Trucks

1 Answer

Fuel pump 04 e450 ford super duty diesel - Cars & Trucks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 34 Answers

Inside of the tank if I not misstaking is 2 pumps

Posted on Nov 07, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: 2000 ford f250 super duty 4x4 7.3L diesel oil leak

The HPOP (high pressure oil pump) is right under the filter housing. There are 2 lines that distribute the oil to the cylinder heads. The o-rings on those fittings go out. Kit is available from Ford or International. You will need a special wrench to get to the fittings though.

Posted on Jun 23, 2008

localwonder
  • 6784 Answers

SOURCE: Transmission trouble on 2002 Ford E-450 Super Duty

Hi, this is a defective OD shift solenoid that is located inside the trans pan. you will have to drop this pan in order to extract it for replacement. this solenoid, if damaged, cant initiate the shift sequence required for the OD to engage during operational procedures.

Simply replacing this solenoid will fix this issue.

NOw, concerning the erratic shifts. this is isolated within the transmission control module. it seems to be malfunctioning. you will need to replace this module as well.

Posted on May 21, 2009

pippall
  • 1486 Answers

SOURCE: I have a 1999 Ford F450 super duty diesel. It

Replace the glowplug relay.Its faulty.The glow plugs stay on until engine warms up.The engine temp switch then activates the relay to switch off.So it could be the temp switch also faulty.

Posted on Jul 17, 2009

  • 4 Answers

SOURCE: remove and install diesel fuel injector

First, keep everything as clean as possible. Contamination below 30 microns, which cannot be seen by humans, can destory a diesel fuel injection system. Clean everything off anything having to do with connections on the fuel system and cover any connections left open.

Begin by removing the intake manifold. This will remove the clips holding the injection lines passing underneath and around the intake runners. After removing the manifold, cover the openings in the cylinder head (I use wadded-up paper towels).

Next, remove the clips at the brackets on the injection lines closer to the injectors.

Loosen all of the injection connections at the injectors. Do not remove the lines.

You can remove the water crossover tube if it is in your way, but drain about a 1/2 gallon of coolant before your remove the crossover.

Remove the oil fill tube from the timing cover. Turn the engine clockwise, using a 15/16" socket and ratchet (or breaker bar) on the center bolt of the crankshaft. As you turn the engine over, a bolt will show up at the opening where the oil fill tube was removed. Remover the bolt and keep turning the engine over until you have removed all three bolts. Do NOT use the starter to turn the engine over and, after removing the third bolt, do NOT turn the crankshaft any more.

On top of the timing cover, behind the rounded top, is the place where the injection pump is bolted to the cover from the back side. Clean the top of the timing cover where it meets the injection pump and look for a thin line scribed into the cover and one on the injection pump. Note the position of the two lines (they are usually aligned) for reassembly.

Remove the throttle cable assembly from the injection pump. Remove all the wires from the pump and note which connection the big pink wire goes to. The other wires will be green. Remove the return hose at the top of the injection pump.

There are three nuts holding the injection pump to the timing cover and you will need a 15mm socket and/or wrench to remove them. When you do, the injection pump and injection lines can be removed as a unit. Note the position of the driveshaft of the injection pump to set the new one the same way. If you are not going to put things back together right away, cut up a plastic garbage bag and make covers for the injectors. Secure the covers with rubber bands or nylon cable ties to keep dirt out of the injectors.

Carefully transfer the injection lines to the new pump. It is possible to cross them up so pay close attention while moving the lines. Transfer the fuel inlet pipe to the new pump and whatever device is mounted on the passenger side of the old injection pump to the new pump.

Get a new injection pump to timing cover gasket and install it over the timing cover studs. Install the new injection pump after setting the driveshaft to match the holes in the gear inside the timing cover. The pump can only be installed one way since it is indexed to the gear. Reinstall the nuts on the studs and set the timing marks to the same position they were when you removed the old injection pump (the lines on top of the timing cover and the flange of the injection pump). Tighten the mounting nuts. Make sure that all the injection lines line up at their injectors, but do not tighten the connections at the injectors yet.

Put the first bolt back into the gear through the oil fill tube hole. Hand tighten it and then turn the crankshaft clockwise as before to install the remaining two bolts. Then, tighten all the bolts securely and resinstall the oil fill tube. Reinstall the throttle connections on the injection pump.

Install a new piece of 1/4" fuel line from the fuel filter to the injection pump (the old one is usuall brittle since it never gets changed). Remove the covers over the opening in the cylinders heads and reinstall the intake manifold using new gaskets.

Reinstall all the injection line clips that were removed and the coolant crossover tube (if you removed it and don't forget to add coolant to the radiator). Reconnect all the wiring on the injection pump, except for the big pink wire. Install a piece of clear tubing on the top of the injection pump and connect it to the return tee in front of it (where you removed the rubber hose from the old injection pump).

Now comes the fun part: Disconnect the glow plug relay connector (two small wires in a connector) from the middle of the relay. The relay is usually on the driver's fender and close to the battery.

Crank the engine, in short bursts, until you see fuel in the clear tubing on top of the injection pump. When you do, reconnect the big pink wire on the injection pump. Continue to crank the engine in short bursts (allowing the starter to rest between cranking cycles) until you see fuel dripping out of the injection lines at the injectors. When you do, tighten the connections where fuel is dripping. When all lines have been tightened, reconnect the glow plug relay connector. Remove the clear tubing on top of the injection pump and reinstall the fuel line that was removed from that location.

Then, try starting the engine normally. If it will not start, try some WD-40 down the intake. You can use ether, but you MUST disable the glow plugs be removing the connector at the relay.

The engine may run rough or stall at first but it should smooth out after all the remaining air comes out of the system.

Torque values are as follows:

Intake manifold: 25-37 ft-lbs
Gear bolts: 13-20 ft-lbs
Injection pump mounting nuts: 25-37 ft-lbs
Injection lines: 15-24 ft-lbs ("wrench tight" is fine)
Injection pump fuel inlet fitting: 15-20 ft-lbs

Posted on Feb 17, 2010

protuha
  • 208 Answers

SOURCE: fuel capacity. for 2002 ford f250 super duty crew

Fuel capacity is 38 galons.
Found it on:
http://consumerguideauto.howstuffworks.com/2002-ford-f-250-f-350-super-duty-13.htm

Posted on Nov 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuel pump ford e450


if its a gas engine it is located in the tank. if its a diesel its located on the drivers side frame rail

Mar 11, 2013 | Ford Cars & Trucks

1 Answer

I think i ran my 1999 ford e450 out of fuel, how do i prime it and or test the pump


remove fuel filter fill it with fuel there is a bleeder there have som eone crank engine press bleeder until air bubbles are gone and just fuel comes out

Mar 19, 2011 | 1999 Ford Super Duty F 450

1 Answer

MI have a 2004 f250 super duty diesel 4x4 lariat and i recently put all new batterys on it and fill it up with diesel, now it trys to start but its acting like its not getting any fuel, someone told me it...


Take the small fuel filter cap loose under the hood and have somebody hit the key to on. Fuel should come gushing out... If not check filter on frame rail. ....then pump

Jan 12, 2011 | 2006 Ford F-250 Super Duty

1 Answer

Hey i got a 99 ford e450 7.3 turbo diesel and my turbo wont work dont know if its a fuse and where it is or if its the hole thing


there shuld be a fuse in the turbo wiring looom also check to see if connection is properly wired up

Oct 22, 2010 | 2002 Ford Super Duty F 450

1 Answer

Replaced fuel lines on my 2000 F-250 super-duty 7.3 diesel now will not fire. primed fuel filter bowl several times no luck


YOU HAVE AIR IN THE SUCTION LINE.OR YOUR ELECTRIC FUEL PUMP FUSE IS BLOWED OR PUMP IS FAULTY IF YOU CANT GET NO FUEL TO FLOW.

May 25, 2010 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

Removing radiator 2006 E450 Diesel


its not easy! the best way is for me to guide u through it! if u would like to call !9082795717tep by step! but must leave good feed back!

Feb 10, 2010 | 2006 Ford F 350 Super Duty

1 Answer

WATER IN THE FUEL TANK


The drain is on the frame mounted fuel pump 6mm allen plug
Don't strip it!

Dec 26, 2008 | 2008 Ford F 250 Super Duty 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...