Question about 1992 Ford Explorer

1 Answer

No power to the sending unit - 1992 Ford Explorer

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 51 Answers

Check make shure you have a good ground check feuses and relays

Posted on Nov 07, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

If the fuel sender wire from tank connects to full side terminal on guage...does power wire hook to empty side of guage?


Year make and model ?
If you have a separate gauge, the power would go to + and the sending unit would go to - .

Mar 20, 2016 | Cars & Trucks

2 Answers

What is the sending unit and were is it located on my Chevy camaro 3.8 v6 1998


you will have several sending units.
1. Oil pressure sending unit, which according to peoples site that I have visited is right above the oil filter.
2.sending unit in gas tank going to gauges, which is in the gas tank.
3. temperature sending unit, which is located near the thermostat housing or near the end of the upper radiator hose.

Feb 05, 2015 | Cars & Trucks

1 Answer

My fuel gauge is not working, have a 70 Dodge Challenger, have replaced sending unit in tank, dash unit, voltage limiter and checked continuity between wires to gauge and sending unit, and made sure dash...


Only thing I can tell, with all you've checked, is the power to the gage isn't there. If the tank sending unit ground to frame is not connected, the gage will go past the full mark. No power to the gage it will stay at empty side. Power goes from fuse to gage, gage to sending unit and back to gage. Make sure the fuse is good on both sides of it. The gage just isn't getting power from the fuse.

Jan 13, 2018 | Dodge Challenger Cars & Trucks

1 Answer

2001 chevy 1500 5.3l 4x4 fuel guage not working. changed sending unit no change. grounded gauge in dash went to full not guage. not getting power to sending unit fuses/ wiring good


You won't get power at the sending unit. The sending unit provides a variable ground to the dash unit. Where did you ground the dash unit? If you disconnect the sending unit at the tank and ground the fuel gauge circuit there the gauge should go to full. If if doesn't the problem is between that connector and the place you cheched it before. If it does the problem is with the sender. Occasionally new parts are found to be defective.

Apr 17, 2011 | 1999 Chevrolet Silverado 1500

1 Answer

Fuel guage dosent work is there got to be power to the sending unit


Yes, there needs to be power to the sending unit (usually located with the fuel pump in the fuel tank) for the sending unit to work. Check the fuel pump fuse and relay to be sure both are OK.

Mar 03, 2011 | 1992 Isuzu Rodeo

1 Answer

2005 express fuel gauge shows emrty all the time? how do i know if its the sending unit or just a bad gauge


you have to back track the wire from the sending unit to the guage. If there is no power when you put your volt meter to the wire and the body you should get movement. There could be a break in the wire, or it could be a bad guage or a sending unit. obviously the sending unit is the hardest to fix. So start with the wire, then the guage then the sending unit. If you do replace the sending unit. I personaly would replace the wire no matter what. One solid wire with a good heat and weather proof coating.

Jun 06, 2009 | 2005 Chevrolet Express

1 Answer

Oil pressure gauge keeps fluxuating. Think it is the sensor. Want to know where the sensor is located on my 1994 lincoln continental


The oil sending unit is located below the power steering pump. 
You can get to it by removing the alternator, then the three bolts around the power steering pump bracket. Remove the small pulley on the bracket and pull back on the power steering bracket. Look behind bracket and you will see the oil sending unit. 

Disconnect the wire from the oil sending unit. Use a deep socket (1 1/16) to remove unit. 

While you have unit remove, I would go ahead and use an oil pressure gauge to test the oil pump pressure. 

Good luck and hope this helps

May 02, 2009 | Ford Lincoln Continental Cars & Trucks

1 Answer

Replaced sending unit no power to the sending unit but juice to the fuse and relay


is there power coming out of the relay going to the sending unit?

Apr 17, 2009 | Toyota Pickup Cars & Trucks

1 Answer

Sending unit has no power


ok we the mechanics know the sending unit as a sensor inside the fuel tank and they do not get any power they get groun and send a regulated ground to teh fuel gage,
if this not answer your question please be more specific about what sending unit are you talking about

May 22, 2008 | 1995 Ford Aspire

Not finding what you are looking for?
1992 Ford Explorer Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

80531 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...