Question about 1994 Dodge Caravan

1 Answer

I need to see how the hoses are hooked up to the radiator in the front of the vehicle

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 14,337 Answers

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I want to replace the water pump on my 2005 Cadillac CTS 3.6 L engine I'm wondering what the best way would be to drain the radiator and also what should I torque the bolts to


Draining Procedure
  1. Park the vehicle on a level surface.
  2. Remove the surge tank cap.
  3. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  4. Remove the air deflector. Refer to Front Air Deflector Replacement in Body Front End.
  5. Place a drain pan under the lower radiator hose connection at the bottom of the radiator.
  6. Using J 38185 slide the hose clamp back on the hose.
  7. Slowly remove the lower radiator hose and drain the coolant into the drain pan.
  8. Inspect the engine coolant for the following conditions:
?€¢
Discolored appearance -- follow the flush procedure. Refer to Flushing .


?€¢
Normal in appearance -- follow the filling procedure.

Oct 12, 2016 | 2005 Cadillac CTS 3.6

1 Answer

Waterpump 2002 ford turaus 3.0 durtec


3.0L Engine

VIN S Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
  • Splash shield
  • Lower heater hose
  • Radiator lower tube bolt
  • Radiator upper front tube bolt
  • Air cleaner assembly
  • Battery and tray
  • Water pump belt
  • Upper radiator hose
  • Engine vent hose
  • Transaxle 10 pin connector
  • Radiator bypass hose assembly
  • Thermostat housing
  • A/C compressor brace, if equipped
  • Water pump mounting nuts
  • Connector hose
  • Water pump




25996402-nto4xxgg4h3g52i5qee3bm1e-1-0.gif
To install:
  1. Install or connect the following:
  • Water pump
  • Connector hose
  • Water pump mounting nuts and tighten them to 15-22 ft. lbs. (20-30 Nm)
  • A/C compressor brace, if equipped, and tighten the nuts to 15-22 ft. lbs. (20-30 Nm)
  • Thermostat housing
  • Radiator bypass hose assembly
  • Transaxle 10 pin connector
  • Engine vent hose
  • Upper radiator hose
  • Water pump belt
  • Battery and tray
  • Air cleaner assembly
  • Radiator upper front tube bolt
  • Radiator lower tube bolt
  • Lower heater hose
  • Splash shield
2. Fill the cooling system.
3. Start the engine and check for leaks.

Dec 06, 2015 | 2002 Ford Taurus

1 Answer

Location of thermostat


Open the hood and find the radiator.
Get help and a flashlight if you need to.
The radiator should have two black hoses attached to it, one on top and one on the bottom.
Those hoses are about 2 inches in diameter, maybe a little larger.
On cars made up to about 1985, the thermostat was found at the engine end of the top radiator hose.
There would have been a bell-shaped housing with the thermostat inside.
These were usually rear wheel drive vehicles.
Cars made since the mid-80's and particularly front wheel drive vehicles have the the thermostat located at the engine end of the lower radiator hose.

Jan 19, 2013 | Cars & Trucks

1 Answer

Where is the freon refill port on a 1998 ford windstar


On the passenger side of the vehicle. look at the 2 A/C lines coming from the front of the vehicle from the condensor. (to the left of the radiator if standing in front of the vehicle) one of thoses 2 hoses wil be turning downward in about a 90 degree angle and it is right on one of thoses 2 hoses. I believe there is a radiator hose right above it blocking your view of it (pretty sure it's a radiator hose but know for sure there is a hose blocking the view). So basically right behind the radiator on the passenger side directly on one of the 2 A/C lines going towards the back of the vehicle. Best I can explain. Hope this helps and good luck.

Jul 21, 2011 | 1998 Ford Windstar

1 Answer

Location of therma stat


Hello,
The location of the thermostat for most vehicle.

Stand in front of the car with the hood open, you'll see a black hose hooked to the upper side of the
radiator.( about 2 inch in diameter, newer vehicles about 1 and 1/2 inch, and newer small cars
about 1 and 1/4 inch. ) Follow the hose to the other end, it connects to the thermostat housing. The thermostat is inside of the housing.( the hose usually goes to the air intake manifold, but some
housings are on the side or back of the engine. )

I hope this helps you.

Feb 02, 2011 | 2006 Chrysler Town & Country

2 Answers

Location of water pump on 1995 Jeep Cherokee


front of engine behind pully see water hose on top of radiator follow hose and you have found the pump.

Jul 14, 2010 | 1995 Jeep Cherokee

1 Answer

2001 vw beetle service manual ? need to change water pump, how hard is it? dont look to bad.


Check this procedure to how to replace a water pump (DIY Complexity: Moderate / Time: 3.5 hours):

Parts:
1. Water Pump

Tools:
1. Screwdriver
2. Scraper
3. 3/8 in. Drive Ratchet
4. Cooling System Pressure Tester
5. Needle Nose Pliers
6. Socket Set
7. Radiator Hook Tool

Supplies:
1. Coolant
2. Silicone Sealant

Steps:
Step 1 With the engine off and cold, open the hood and locate the vehicle’s water pump.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.
o Tip: Before removing the radiator cap, squeeze the upper radiator hose to verify that the cooling system is not pressurized.

Step 2 Remove the radiator cap.

Step 3 Install cooling system pressure tester. Apply the pressure indicated on the radiator cap or in the owner’s manual.

Step 4 Inspect cooling system components for leaks.

Step 5 Place a drain pan under the radiator. Open drain valve or remove the lower radiator hose to drain cooling system.
o Tip: Depending on the vehicle, lifting the vehicle may be required to gain access to the lower radiator hose.

Step 6 Remove the drive belts or serpentine belt.

Step 7 Remove any hoses connected to water pump.

Step 8 Unbolt water pump from engine. Remove the water pump.

Step 9 Using a gasket scraper, clean the mating surface on the engine block.

Step 10 Install new water pump and new gasket. Tighten bolts to manufacturer’s specifications.
o Tip: You may want to use a light bead of silicone designed for water pumps.

Step 11 Re-install any hoses and belts that were removed.

Step 12 Re-install drain plug or lower radiator hose.
o Tip: Squeeze the radiator hose. If it feels soft you may want to replace the hose at this time. Always use new hose clamps.

Step 13 Refill radiator with a 50/50 mix of coolant and distilled water, then pressure test the cooling system and check for leaks.

Step 14 Fill overflow reservoir with same mixture.

Step 15 Leave the radiator cap off, start engine and let it idle. You should see the system“burping” bubbles of air. Refill the radiator to the top.
o Tip: Most air is expelled after a couple minutes of idling. Be cautious of potentially hot fluid overflowing.

Step 16 Install radiator cap.

Step 17 Road test vehicle, keep an eye on the engine temp gauge if vehicle runs hot, there still might be an air pocket in the cooling system. The cooling system should be topped off after vehicle has fully cooled down.

Good luck.

Mar 29, 2010 | 2001 Volkswagen Beetle

1 Answer

What is the procedure for removal of the radiator from the Mercury Mystique(1998 model)?


Ford Contour/Mystique/Cougar 1995-1999 Repair Guide

Radiator -REMOVAL & INSTALLATION
(see Figures 1 through 7)

7249321.jpg
Fig. 1: Remove the upper radiator hose from the radiator


d2d2436.jpg
Fig. 2: Use a back-up wrench to remove the transaxle cooler line connections-automatic transaxle only


3213ac8.jpg
Fig. 3: the lower transaxle cooler line connection


ec9272d.jpg
Fig. 4: Remove the passenger side radiator mount and ...


956cd3d.jpg
Fig. 5: ... and the driver's side radiator mount


f06fec0.jpg
Fig. 6: The condenser can be support using mechanic's wire as shown here, or another suitable device


242d821.jpg
Fig. 7: Carefully lower the radiator out the bottom of the vehicle
  1. Disconnect the negative battery cable.
  2. Drain and recycle the engine coolant.
  3. Remove the upper radiator hose from the radiator.
  4. On 2.5L equipped vehicles, remove the radiator overflow hose from the radiator.
  5. On vehicles equipped with an automatic transaxle only, remove the transmission cooler line from the cooler inlet fitting and plug the line and the fitting.
  6. Remove the engine fan.
  7. Raise and support the vehicle.
  8. Remove the lower radiator hose from the radiator.
  9. On vehicles equipped with an automatic transaxle only, remove the transmission cooler line from the cooler outlet fitting and plug the line and the fitting.
Remove the cooler lines while holding the radiator connector with a back-up wrench.
  1. Support the radiator, and A/C condenser with a jackstand or other suitable device.
  2. Remove the lower radiator supports from the front of the subframe.
  3. Remove the two retaining bolts for the A/C condenser from the brackets at the bottom of the radiator.
  4. Position the jackstand aside and remove the radiator out the bottom of the vehicle.
To install:
  1. Carefully raise the radiator into place and support the radiator with a jackstand or other suitable device. Install the two retaining bolts for the A/C condenser into the brackets at the bottom of the radiator.
  2. Install the lower radiator supports and tighten the bolts to 71-97 inch lbs. (8-11 Nm).
  3. Remove the jackstand and install the transmission cooler outlet line (if equipped) and the lower radiator hose to the radiator.
  4. Lower the vehicle.
  5. Install and tighten the fan shroud nuts.
  6. Install the transmission cooler inlet line (if equipped) and the upper radiator hose to the radiator.
  7. On 2.5L equipped vehicles, install the radiator overflow hose from the radiator.
  8. Connect the negative battery cable.
  9. Fill the cooling system with the proper 50 / 50 mixture and start the vehicle.
  10. Bleed the cooling system and check for leaks.

Hope helps with this (remember rated this help) Good luck.

Jan 20, 2010 | 1996 Mercury Mystique

2 Answers

How to remove a radiator from a ford taurus


Disconnect battery ground cable. Remove battery. Remove battery tray. Remove clip retaining contant control relay module and position module aside. Remove radiator cap. Raise vehicle front end as high as possible. Remove radiator splash shield. Drain radiator. Remove the radiator mounting bracket assembly. Remove lower radiator hose. Partially lower vehicle. Remove upper radiator hose. Remove radiator overflow hose. Remove upper A/C condenser core retaining bolts. Remove upper transmission oil cooler tube clips. Remove lower transmission oil cooler tube. Raise vehicle. Remove lower transmission oil cooler tube clips. Remove lower transmission oil cooler tube. Remove transmission oil cooler bracket and position transmission oil cooler aside. Remove lower A/C condenser core bolts and position A/C condenser core aside(be careful not to loosen the AC condenser lines. Remove radiator support bracket. Remove radiator out through the bottom of the vehicle.
Installation
Position radiator. Position radiator support bracket and tighten nuts. Position A/C condenser core and tighten lower A/C condenser core bolts. Position transmission oil cooler tube and install transmission oil cooler tube bracket. Install lower transmission oil cooler tube. Install lower transmission oil cooler tube clips. Install lower radiator hose. Install radiator mounting bracket assembly. Tighten bolts. Install radiator splash shield. Lower vehicle. Install upper tranmission oil cooler tube. Install upper transmission oil cooler tube clips. Install upper A/C condenser core retaining bolts. Tighten bolts. Install radiator overflow hose and tighten clamps securely. Install upper radiator hose. Position constant control relay module and clip securely. Install battery tray. Install battery. Connect battery ground cable. Fill and bleed cooling system. Start engine and inspect for leaks.

Nov 25, 2009 | 1998 Ford Taurus

Not finding what you are looking for?
1994 Dodge Caravan Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...