Question about 2005 Ford Bantam 1.3i

Open Question

Adjust hand brake on ford batum rocam

Im looking for a diagram of rear wheel brake system. I need to adjust the hand brake and would also like to know how to refurbish brake boosters. Thanks

Posted by Anonymous on

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 196 Answers

SOURCE: fading brake pedal

Perfect well at this point i would say that tha abs valve is bypassing fluid. If you can un hook the line that comes into the abs valve and plug it and try and bleed the system where you cap the line going into the abs valve. If you get a good pedal after pluging the line going into the abs valve this tells me that the abs valve is bypassing fluid give it a try i have ran into this a few time and the abs valve has been bad. Also can you rate this sluton also i do hits on my own free time thanks good luck

Posted on Jan 18, 2009

  • 2 Answers

SOURCE: what torque for rear wheel bearing Ford Focus 2000

Can only find out that the hub needs to be tightened to
235 nm Dunno if this helps

Posted on Jan 27, 2009

  • 79 Answers

SOURCE: need a diagram for rear brakes on 2000 ford ranger


I just replace mine this weekend. I know how you feel.

Posted on Feb 17, 2009

  • 70 Answers

SOURCE: how do I adjust emergency brake cable on 1999 ford

FIRST adjust rear brake starwheel while spinning tire FOWARD. then alongside drivers side of car find emergency brake cable adjustment (long threaded rod with nut) . hold one end of rod with vise-grips and turn nut until emer. brake cable has less slack in it. now go inside car and apply dont want the pedal to stop right away but u also dont want too much"travel" in the about halfway is IDEAL. IMPORTANT- once the brake cable is adjusted and the car wont roll foward in gear with the brake on and applying a little "gas"-make sure with brake OFF that rear wheels turn freely. hope this helps.

Posted on Aug 31, 2009

  • 512 Answers

SOURCE: I need a diagram for the rear drum brake for 2002 Ford Ranger

Copy and paste this into your search window: 2002 ford ranger rear brake diagram

You should see four pictures pop up, select the brake parts diagram or the brake picture.

Posted on Sep 03, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

3 Answers

How do I fixed if my car hand brake stuck 2001 toyota coralla manual

There are several things that can make a hand brake stick on. It possible the cable attached to the leaver has come off it guide. There is a cable running from each rear wheel to the handbrake leaver , a inner cable running through a outer housing , chick that the inner cable is free to move back and forward . if all the cables are free to slide adjust the rear brakes and hand brake as instructions . Slacken off the hand brake cable adjustment. Jack up the rear wheals and adjust the brake shoes till the brakes lock, then back off till the wheels are free to turn. Then pull the hand brake leaver on two clicks and adjust the hand brake cable till the rear wheels just start to bind, release the hand brake leaver and check the wheels are free to turn.

Nov 27, 2014 | 2001 Toyota Corolla

1 Answer

Adjust handbrake 94 libero

  • Remove the center console covering the parking brake lever. Locate the parking brake lever between the drivers seat and the front passenger seat. Put the parking brake lever in the lowest position.

  • 2

    Turn the cable adjuster locknut to make the nut loose. Find the nut at the base of the parking brake lever.

  • 3

    Raise your GT rear wheels using a jack and support the rear wheels using jack stands. Remove both rear wheels using a tire iron to loosen and take off the lug nuts. Take off the tire from the rods by hand.

  • 4

    Get underneath the car and remove the rubber hole plugs from the brake rotors. Locate the rotors on the underneath inside of the wheel wells.

  • 5

    Take off the brake calipers with a screwdriver, but do not disconnect the brake fluid lines.

  • 6

    Use a pry bar to push up on the parking brake self adjuster wheel. Locate this next to the brake caliper and it looks like a star wheel. Rotate this wheel until the rotors will not turn.

  • 7

    Turn the adjuster wheel five notches in the opposite direction. Reinstall the calipers and wheels. Lower your GT using the jack and remove the jack stands from the rear wheels.

  • Sep 13, 2012 | Mitsubishi Cars & Trucks

    1 Answer

    Need diagram for rear drum brakes on 2004 mercury sable

    Try using a Web search and use Photos for the word Diagram. If you use Diagram, most likely all you will get is a linear Diagram similar to a wiring Diagram and of no use to you.
    Drum brakes are easy, just take off the rubber adjuster cover and tweak the STAR wheel to collapse the brakes and make them narrower. Sometimes you may have to loosen the Emergency brake cable because it cantilevers the only brakes you have in the rear wheel. (Unlike a Rotor which has 2 brake systems inside of each rear wheel.)

    Dec 10, 2011 | 2004 Mercury Sable

    1 Answer

    Hand brake not working moves up and down and does not assist with brake holding

    You may have the brakes out of adjustment or a broken ebrake cable, the first thing is to go under the truck and have someone apply the e-brake and see if both rear cables are pulling. im not sure if you have drum or disc in the rear of this jeep but they both use cables, if the cables are working then you will need to remove the wheels and check the brakes, the brakes may be worn or out of adjustment.hope this helps.

    Mar 10, 2011 | 1994 Jeep Cherokee

    1 Answer

    1998 ford escort se hand brake need adjusting. doesn't hold.

    Try to adjust the rear brakes tighter at the shoes, if you have drum brakes. May require taking the drum off and adjusting the adjuster. Or, adjusting it from the backing plate access hole if there is one.

    Be sure to check the cables to make sure they are not broken anywhere between the hand brake lever and the back brakes.

    Good luck on this repair.


    1. Raise and safely support the vehicle.
    2. Remove the wheel and tire assembly.
    3. Remove the brake drum.
    4. Using a brake adjusting gauge, measure the inside diameter of the brake
    5. Compare the brake drum measurement to the brake shoes.
    6. Adjust the brake shoes by inserting a brake adjustment tool into the knurled
      quadrant of the rear quad operating lever and adjust the shoes to the same
      measurement as the brake drum.
    7. Install the brake drum.
    8. Install the wheel and tire assembly.
    9. Lower the vehicle.
    10. Check the brake system operation by making several stops while driving
      slowly forward.

    prev.gif next.gif

    Nov 02, 2010 | 1998 Ford Escort

    1 Answer

    Loyota Levin BZR rear hand brake adjustment

    Try backing the car up while working the hand brake, Had this problem before on a customers Mazda.

    Mar 06, 2010 | 1999 Mazda 626

    1 Answer

    Brake shoes

    I would have to send you pics. This system uses a spring loaded adjuster which you can use a screwdriver through the rear of the backing plate and listen for the clicks but, if you go too far you may sieze the wheel. You need a very light drag when rotating the drum by hand or with the wheel on and then test the e-brake for tension and hold. If you wish to have diagrams, email me at

    Feb 27, 2010 | 1995 Ford Contour

    4 Answers

    Parking Brake doesn't work. I have adjusted the

    Check your rear brakes and their adjustment. If parking brake is seperate check them also. The brakes have to work and be adjusted properly then adjust parking brake.

    Sep 08, 2009 | 1996 Jeep Grand Cherokee

    1 Answer

    Bmw 320cd 2006 model handbrake

    Hi, if you lift the hand brake gaitor that covers the lever you will see what looks like a spring with a washer and a clip passing through the washer. Release the handbrake lever to release tension on the cable then unclip the clip from the washer, then you will need to remove one wheel bolt to gain access to the adjuster rod. Raise the rear wheels so that they rotate freely and look through the hole left by the removed wheel bolt untill you see a toothed wheel. Using a long screwdrive you will need to adjust this wheel untill the road wheel does not move then wind the toothed wheel backwards (approx 6 teeth) do this for both wheels, once done fully release the hand brake lever and the clip should relocate in the washer, this should then have adjusted the hand brake

    Feb 11, 2009 | 2008 BMW 3 Series

    1 Answer

    Rear brakes need adjustment

    If you look at the bottom of the rear brake drum you should find a little opening sometimes it has a rubber plug inserted in it. Pull out the plug and use a thin straight screwdriver to feel for the adjuster. The adjuster has a spoked wheel on it thatyou can turn with the screwdriver just turn it a couple of clicks at a time till you feel drag on the wheel whenyou turn it by hand.

    Jan 01, 2009 | 1997 GMC Sierra

    Not finding what you are looking for?
    2005 Ford Bantam 1.3i Logo

    Related Topics:

    464 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts


    Level 3 Expert

    75807 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22133 Answers


    Level 3 Expert

    5495 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides