Question about 2001 Mazda Tribute

1 Answer

Loose heater a/c wire for temp control knob - 2001 Mazda Tribute

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mazda Master
  • 76,846 Answers

You will need to go to the dealers parts dept and have them look up what is needed to fix this, more than likely the whole assembly will need to be replaced, about $300.00

Posted on Nov 07, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No heat but a/c ok


Either your heater blend door is stuck or the vacuum line to the blend door has fallen off.
Was your heater working before? It is possible that the heater core was bypassed due to a leak (not uncommon in Ford products).

May 14, 2015 | 2008 Ford Ranger 2WD

1 Answer

My heater wont work in my truck it will blow air but it wont warm up. whats wrong or how do i fix it?


If your engine temperature gauge reads normal, then the heater control (temperature setting) is probably at fault. If the temp gauge remains on COLD, then the thermostat is probably stuck open and needs to be replaced. If the temp is normal do the following:
With the truck running (outside, of course), go to the passenger side of the truck and remove the panel that is just under the glove box. Inside that area is the heater core and the controls to operate the hot/cold vents. With a flashlight in hand look in that area as someone moves the temp lever or control from hot to cold. You should see movement of the cable to the heater core. If nothing is noted, check for loose wires, disconnected cable and any vacuum leaks. You may have to replace the heater control unit. On a vehicle of this age, your best bet would be a salvage yard or EBAY...
Good Luck and I hope this helps...

Nov 24, 2013 | 2000 Chevrolet Silverado 1500

1 Answer

Cold air only from heater


first check temp gauge on dash is it normal if so termostat is fine than check the heater hoses going inside from engine compartment if they are hot rule out control valve if it in the engine compartment sit in the vehicle and listen for any noise when you move heater temp switch from cold to hot if you hear clicking noises and no change it may be blend door accutator with moves when you slide or turn heat control nob the heater may have to be removed on some models eexpensive repair may be needed

Jan 21, 2013 | 2007 Toyota RAV4

1 Answer

Hi there everyone PLEASE HELP , I have a Jeep Grand Cherokee 2003. I seem to have a issue with the Heater - everyone whom I have spoken to so far has said its the Blend doors but Im not sure . The issue...


There are two doors , One controls the position of air flow and the other controls temp by allowing the air to pass through the heater core or through the evap core.You will need to remove dash and separate two halves of a/c box to repair blend air door.The way to diagnose the problem is with a scan tool and through the body computer.Swapping parts will get expensive , would probaly be wise to spend the money for a good scan ( not just a code pull).

Jan 22, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

The heater in the car is putting out cold air instead of hot when the motor is at temp. I turn the temp nob to cold then back to hot and it works for a bit then does it all over again. what should I be...


Look for a sticking heater control head. There is a cable that runs from the lever you are moving to a valve that controls the coolant flow into the heater core. Take it to you local Honda dealer for repair.

Nov 21, 2010 | 2005 Honda Civic

1 Answer

The heater in our car is not blowing hot air. It


Check the heater hoses under the hood first to see if they are hot. if they are, there is a temperature control actuator on the top of the heater box. the motors go bad, and the temp door does not move. The motor is hard to get to but if you open the glove box it is to the left, almost behind the radio.

Oct 16, 2009 | 1998 Mercury Grand Marquis

1 Answer

2002 mitsubishi heater not working


approx. $200-250 - takes less than an hour to replace if that part is the problem

Jan 09, 2009 | 2003 Mitsubishi Galant

1 Answer

Air conditioner intermittently (sp?) blows hot air when I am driving. Not consistant with acceleration or turns and just had the freon drained and recharged.


Had the same problem and brought it in and they said it was a problem with the heater control. They said I can replace the hvac control assembly and to get one from a salvage yard. They also said just twist the temp control nob back and forth a couple times till the ac works until i get it

Aug 11, 2008 | 2003 Toyota Highlander

Not finding what you are looking for?
2001 Mazda Tribute Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...