Question about 2002 Toyota Camry

1 Answer

TransAxel not engaging and slipping In drive

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Toyota Master
  • 76,649 Answers

You have a failed transmission here as long as you have not lost the fluid to below the lowest mark on the dipstick. You must remove it and have it rebuilt.

Posted on Nov 07, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hydrostat slips going up hilland you have to keep feathering the pedal to get it to engage


When you say Hydrostat, I automatically think lawn tractop. If this is correct, then the reason it is slipping and just won't go is that your main drive belt is worn and slipping and won't pull. Replace the main drive belt and make sure the belt tensioner is fine and your done.

Jun 13, 2017 | Cars & Trucks

1 Answer

Tranceaxel over heat


I would say your transaxel is worn and ready to come to it's end. The clutches and disks are wearing out and slipping, making the pump work faster. You didn't specify your car, but some transmissions are adjustable and some aren't. If yours can be adjusted, you may be able to save it. GOOD LUCK FRIEND.

Mar 15, 2015 | Cars & Trucks

1 Answer

Ford Explorer, slips in reverse and when you put it in drive you have to rev the engine before it will engage. Once engaged it often slips in between 1st, 2nd and then smooths out after 3rd.


Pull the transmission & rebuild it

You should know when they slip
your done or the trans is

So if it had any chance to be fixed, you
ruined that by continuing to drive it

Now you can get out the check book for
about $3,000.00

Sep 04, 2013 | 2004 Pontiac Grand Prix

1 Answer

2001 Audi A4 Quattro, Reverse slips


Perhaps it is in severe pain, because you failed to identify it it by make and model!

May 15, 2017 | Cars & Trucks

1 Answer

2001 Audi A4 Quattro, Reverse slips


Servo or band worn out, o.ring gone hard or clutch pack burnt out.

May 14, 2017 | Cars & Trucks

1 Answer

Trans drops into 3rd gear won,t shift to 4th


DTC P0734 is "4th gear incorrect ratio" - that's your torque converter 'LOCK UP Clutch" It's worn out (or you're using the wrong Trans Fluid required by Hyundai - SPIII OR Both). The P1624 is simply the Trans Control Unit (computer) communicating to the Engine Control Module (ECM computer) MIL - on request signal to ECM = asking it to turn on "Check Engine" light. MIL = Malfunction Indicator Lamp. When the torque converter 'lock up" clutch slips or doesn't engage, the trans automatically returns to 3rd gear and stays there (it's called 'fail safe' mode) until you cycle the ignition key, then everything resets until the malfunction occurs again.
You'll need to have an AT (Automatic Transaxel) tester hooked up to verify this. Hyundai has a Service Bulletin specifically for "gear incorrect ratio' codes. If when you changed the trans fluid, was it done at a Hyundai Service Center? If not, someone may have installed the wrong fluid.

Jun 01, 2009 | 2000 Hyundai Elantra

1 Answer

Ford F150 lost 4 wheel drive 2003 FX4


Take the hubs apart, inspect them, and clean them, especially the one that you heard a clunk, something might have broke in the automatic hub lock. Make sure everthing gets put back exactly the same, or you'll have more problems. If that doesn't work, then there is something wrong somewhere in the transfer case.

Mar 15, 2009 | 1999 Ford F150 Regular Cab

1 Answer

4 wheel drive out ,


diff unit broke ,drive shaft broke or engaging solonoid not working

Dec 20, 2008 | 1994 Jeep Cherokee Country

2 Answers

1996 chevy K1500 transfer case slipping out of 4 wheel drive


Your trouble is most likely not in the transfer case but in the front differential engagement solenoid.

Dec 20, 2008 | 1996 Chevrolet K1500

Not finding what you are looking for?
2002 Toyota Camry Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...