Question about 1998 Dodge Grand Caravan

1 Answer

Is there an easy way to Relieve the Tensioner Pressure

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

Is it a 6clyd?

Posted on Nov 07, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace belt tensioner


tensioner pulleys are tensioned by the shaft nut in the front of the pulley. Loosen it and then adjust the pulley up or down by the long bolt at the rear of the mounting bracket. IF the pulley is the type used by Ford then loosen the shaft nut and the adjustment is by turning the shaft up or down a toothed rack at the back of the pulley

Feb 01, 2014 | 2007 Jeep Liberty Sport

1 Answer

How do you replace the tensioner on a 1999 Chev 6.5 diesel 350 cube van?


remove the belt unbolt the tensioner and replace. the center of the tensioner has a half inch socket in it . put your pull handle in that socket like you would a normal socket wrench and rotate to relieve pressure on belt remove belt unbolt tensioner

Nov 01, 2013 | 2004 Chevrolet Express

1 Answer

Cant take belt off


Serpentine Belt?

Belt Tensioner uses either a socket or ratchet driver without socket. Usually you pull the tensioner down - counter-clockwise to relieve pressure from belt. Is usually tight you may need a longer lever for leverage.

I hope this helps!

Nov 06, 2012 | 1998 Jeep Grand Cherokee

1 Answer

Replacing tensioner pulley 2004 freestar


whichever direction the bolt must be turned to relieve pressure on the belt... turn it the other way. it may be reverse threaded if the tensioner holds clockwise tension. if the tensioner pushes counter clockwise, it may just be frozen from heat. try putting steady pressure on it with a breaker bar, and then tapping the bolt with a hammer (GENTLY!!). if that fails, you may need to replace the whole tensioner. these bolts are subject to a LOT of heat, and can get pretty badly seized.

Jun 16, 2012 | 2004 Ford Freestar

1 Answer

Replace serpentine belt



Removal & Installation

  1. Rotate the drive belt tensioner clockwise and remove the drive belt.
    WARNING Never suddenly let go of the tensioned idler pulley. The force of the spring pressure suddenly released may damage the idler pulley mechanism. Always release the spring pressure gradually.


    0996b43f80204f01.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Rotate the belt tensioner to relieve tension on the belt-4.6L engine shown, others similar


To install:
  1. Route the belt over the pulleys making sure all the grooves in the pulleys and the belt line up correctly. Refer to the accessory belt routing section of this manual.
  2. Rotate belt tensioner clockwise and slip drive belt over idler pulley on tensioner.

  1. Rotate the drive belt tensioner clockwise and remove the drive belt.
    WARNING Never suddenly let go of the tensioned idler pulley. The force of the spring pressure suddenly released may damage the idler pulley mechanism. Always release the spring pressure gradually.


    0996b43f80204f01.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Rotate the belt tensioner to relieve tension on the belt-4.6L engine shown, others similar


To install:
  1. Route the belt over the pulleys making sure all the grooves in the pulleys and the belt line up correctly. Refer to the accessory belt routing diagrams above.
  2. Rotate belt tensioner clockwise and slip drive belt over idler pulley on tensioner.
If for any reason, the tensioner is crooked, replace it!!! Also, install the belt with the writing facing you like you are trying to read a book. This WILL (a trick I learned at Mercedes) prevent even a new belt from squeeling!!

Dec 16, 2010 | 2003 Ford Explorer

1 Answer

How do I loosen the tensioner for serpentine belt on an S10 1996 chevy? I need to remove the alternator.


The tensoiiner is spring loaded. On the front of it in the center is a nut, get the correct size socket attached to a breaker bar and rotate the tensioner to relieve the pressure and hold it while you remove the belt

Apr 01, 2010 | 1996 Chevrolet S-10 Pickup

1 Answer

How difficult is it to change a serpentine belt on a 96 ford expidition 6 cylinder???


fairly easy theres a belt tensioner that you rotate to relieve tension remove belt install new one rotate tensioner put belt on release tension start engine check belt then your done

Jan 18, 2010 | 1996 Ford Explorer

1 Answer

Changing fan belt


Removal & Installation
  1. Rotate the drive belt tensioner clockwise and remove the drive belt.

    WARNING Never suddenly let go of the tensioned idler pulley. The force of the spring pressure suddenly released may damage the idler pulley mechanism. Always release the spring pressure gradually.

f897cde.gif
Rotate the belt tensioner to relieve tension on the belt—4.6L engine shown, others similar

To install:
  1. Route the belt over the pulleys making sure all the grooves in the pulleys and the belt line up correctly. Refer to the accessory belt routing section of this manual.
  2. Rotate belt tensioner clockwise and slip drive belt over idler pulley on tensioner.

Oct 11, 2009 | 1996 Ford Explorer

1 Answer

97 Taurus Belt tensioner does not lossen the belt


There should be a square big enough to fit a 3/8" drive ratchet into on the tensioner (should be closest to the pulley), insert the ratchet into that square, then try turning the tensioner, this should release the pressure on the serpentine belt. Hope this helps.

Mar 15, 2009 | 1996 Ford Taurus

Not finding what you are looking for?
1998 Dodge Grand Caravan Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...