Question about Cars & Trucks

Open Question

Where is the starter relay for a 2002 nissan altima

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
jschoon77
  • 55 Answers

SOURCE: DOOR WON'T OPEN FROM INSIDE OF NISSAN ALTIMA 2002 ON DRIVER'S SIDE

There is a cable that attaches to the inside door latch release handle. The plastic that retains this cable is most likely broken. I have seen this before. If the retainer is not holding the cable sheath correctly, the entire cable moves when the handle is pulled and does not release the door latch.

Remove the door panel and inspect this cable. You will see 2 cables (one is for the door lock). If the plastic is broken, you will need a new interior handle assembly.

Hope this is helpful!!



Nissan Scope Technician- 10+ years experience in Nissan dealership

Posted on Nov 11, 2008

Ad
  • 383 Answers

SOURCE: replacement of a head gasket on 2.5 liter nissan altima 2002

frajogag: First off, be aware that these bolts are "torque to yield" bolts (streach bolts). What this means is that instead of torqueing the head bolts to a specific torque specification, they are torqued down to a set spec and then tightened by rotating the bolts a certain angle, like 90 degrees. and all of them are turned the same amount.
This means that the shanks of the bolts must be checked to make sure they are not too thin (or the bolt has already stretched beyond limits and is prone to snap if used)
Here is how you check the bolts. Measure the bolt using a micrometer, at the base, or within the first 13mm from the end where it threads in. Then go to about 10mm before the threads end heading toward the top of the bolt. There should not be more than a 0.23mm (.0091 inch) or less difference or the bolt should be discarded.
Torque the bolts down to 98.1Nm ( 72.ft lb)
Looking at the head from the side, so you are looking at the full length from side to side, I will number the head bolts in this fashion.
#1 & 2 are directly in front of you and in the center of the cylinder head crossing it width wise.
#3&4 are to the left of #1&2, / #5&6 are to the right of #1&2
#7&8 are to the left of #3&4 / #9$10 are to the right of #5&6
Now, you have the sequence.
After the initial pull, back off all the bolts in the same sequence and then retorque them to 36 Nm ( 28 ft lb)
Using a torque angle wrench or having the ability to accurately judge turning angles. Rotate (clockwise) to a 75 degree angle. do this to all the bolts using the sequence I had provided.
Rotate the bolts (clockwise) 75 degrees again on all bolts in the same sequence. The proceedure is complete!

Posted on Apr 23, 2009

  • 54 Answers

SOURCE: Tune up nissan altima 2.5L model 2002

All you really need is a good set of spark plugs, this car has coil packs so no plug wires distributor caps etc.....Just remove the coil packs and install your plugs and your done. Good luck.

Posted on May 31, 2009

  • 1 Answer

SOURCE: 2002 Nissan Altima Exterior Door Handle

I seriously doubt that supergluing or even epoxying a handle back will hold at all, or hold for more then few days.
I would only suggest doing the replacement yourself if you familiar with this type of work, or has the aptitude to figure out how to do it, and have the right tools because it is NOT trivial and a number of things can be done wrong, broken or scratched.
The handle itself cannot be replaced. The outside door handle assembly (which includes the handle, the bezel with all associated springs, plastic and metal hardware) has to be replaced. Besides junkyards, which is a long shot for number of reasons, the only place where the handle assembly can be bought is the dealer. And these handle assemblies are not cheap ether. The driver side handle on my 2002 Altima broke first. I paid $60.23+tax, and they had to order it. BEFORE anyone goes to the dealer I suggest to call first, and ask them if they have it in stock. Since door handles are sold painted they will ask you for your car's VIN number so that they match the paint color.
After you pick it up, the replacement will take about an hour (if you know what you doing). The inside door panel has to be removed, it is held in place by the inside door handle and the panel is attached by a number of clips, the handle assembly is attached to the door by three bolts, to remove which you will need a socket with extension. You will also need a good flashlight so you see what you are doing.
If you are familiar how to do this type of work and plan to keep the car for a while I strongly suggest buying a factory service manual on a CD (I bought mine on eBay for under $10). It is worth its price 1000s of times over, and makes almost ALL repair work SOOO much easier.751424a.jpg73e3811.jpgd240851.jpg

Posted on Nov 16, 2009

ZJLimited
  • 17970 Answers

SOURCE: Howm do I replace a starter on a 1995 Nissan

Nissan 240SX/Altima 1993-1998 Repair Guide

Altima
(see Figures 1, 2 and 3)


ef972ea.jpg
Fig. 1: The starter is located to the left of the oil filter housing on the engine block


dfca7b3.jpg
Fig. 2: The starter motor is removed from the bottom side of the engine compartment


04c206e.jpg
Fig. 3: When installing, be sure to align the starter's mounting bolt holes with those in the engine block

  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. Remove the starter support bracket, as required.
  4. Label and disconnect the starter electrical harness.
  5. Support the starter from beneath the vehicle using a jackstand.
  6. Remove the starter mounting bolts.
  7. Carefully lower the starter from the vehicle.
To install:
  1. Position the starter on the engine and support it using a jackstand.
  2. Install the starter mounting bolts and tighten to 30-37 ft. lbs. (40-50 Nm).
  3. Connect the starter electrical harness.
  4. Install the starter support bracket, as required.
  5. Lower the vehicle.
  6. Connect the negative battery cable.

Hope helped with this (remember rated this help) Good luck.

Posted on Nov 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will a 2002 starter to a Nissan Altima fit on a 1997 Nissan Altima


Nissan Altima was given a redesign.Furthermore, they are guaranteed to fit well on your Nissan Altima.

More information please visit this link:-- Nissan Altima

May 29, 2016 | Nissan Cars & Trucks

1 Answer

How do I know which one is my starter relay in my 97 Nissan Altima?


Usually there will be a chart on the back of lid for the fuzebox. And it will say what kind of fuze it is.

Jun 02, 2012 | 1997 Nissan.5 Altima

1 Answer

My 1997 Nissan altima wont crank over


Test battery, and check for loose connections. Check starter fuse & relay. If you don't hear clicking sounds while trying to start the car then most likely it's a bad starter relay. If your getting voltage to the starter but no click then you have bad starter.

Nov 17, 2011 | 1997 Nissan.5 Altima

1 Answer

I have a 2002 Nissan altima i took it to d the dealer and they said it was the starter and the idpm module , i changed that and it still wont start what should i do


when you say I changed that ,, does that mean you changed both ? if thats the case, you can check the starter relay , and also the ignition itself , Nissan has been having issues with the high flow meter sensor too,, that may be adding to your troubles,, and keep in mind that according to the forums I've read about these issues, not long after the IDPM module goes out,, people are having to replace the catalytic converters due to it dumping unburned fuel into the exhaust system

Sep 21, 2011 | 2002 Nissan Altima

1 Answer

My 2002 nissan altima will not crank at all, is it the fuel pump ? or some other problem. and the weather is very cold.


Check your starter, it might not functioning.
Start withe the starter relay and then to the starter itself.

Try to short the two terminal on the solenid by using a crew dirver would crank the starter.

Dec 10, 2010 | 2002 Nissan Altima

1 Answer

Where is the starter relay for a 1993 Nissan


the car had only theft warning relay location on the front right fender check fuse link location on the front left side fender

Dec 14, 2009 | 1993 Nissan Altima

1 Answer

2002 nissan altima wont crank?


Check the transmission neutral start inhibit switch is not the cause of your problem. (try both 'P' to 'N' positions).
If the headlights work ok there should be enough power in the battery to at least make a solenoid type noise when start is attempted- so it may not be caused by a faulty alternator.
Check the battery terminals are clean and firmly attached to the battery,
Check battery is properly grounded to the chassis and motor,
Check that +12v is available at the starter motor engage solenoid when the ignition switch is held in the 'start' position - check any start slave relay operation.
If all above is OK, you may have a faulty starter motor.

Oct 08, 2009 | 2002 Nissan Altima

1 Answer

I'acontrol m working on a 2002 nissan altima.


where is the ac relay on a nissan altima 2002

Aug 04, 2009 | 2000 Nissan Altima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...