Question about GMC Cars & Trucks

Open Question

Avalanche code co265 and co298 - GMC Cars & Trucks

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 400 Answers

SOURCE: abs codes co281 & co265

the first of the two codes is for the brake light switch, the one that is under the dash attached to the brake rod and brake peddle. Not much to diag on that one, if its bad it's bad, and when it sets the code that means it's bad.
The second one is for the abs modual, it's under the truck on the drivers side. It is bolted to the top of the thing that has all of the brake lines going to it. MOST all of the time that code is set the modual is bad. It can be a little hard to get the bolts out they are torqs 20 or 25(i'm getting old). There are four of them holding down the modual. There are also a couple of connectors going to it. And some of the time it will blow the fuse for the abs under the hood(its in the underhood fues block). Make sure to clean off the modual before you pull it out. You don't want dirt getting in the solinoids for the BPMV(that's the thing it's bolted to).

Posted on Oct 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is code co298 powertrain malfunction on a 2004 chevy avalanche


CO 298 POWER CONTROL MODULE MALFUNCTION..
An ABS code--loss of communication with pcm/vcm.
This needs to be diagnosed by a shop.

Dec 20, 2015 | Cars & Trucks

2 Answers

2000gmc put a rebuilt trany in now wont shift.


The module for the electronic brake control may have a bad ground with 15 years on it. Did the trans not shift at all after installing it ?

Mar 04, 2015 | 2000 GMC Sierra

1 Answer

I have the following codes in my obd scanner. abs codes co298,co283,c0265,co237,co235.


The codes are on the internet

Google them

OBD ABS CODES CO298

Mar 11, 2014 | Cars & Trucks

1 Answer

2006 chevy Avalanche check engine code 172 & 175


the temperature sensor can cause a rich mixture at the wrong time by providing a false reading of cold engine

Sep 28, 2013 | 2006 Chevrolet Avalanche

1 Answer

Co298 co287 co265


Google the codes to see what they are
& how to diagnose them

Sep 08, 2013 | 2004 Chevrolet Avalanche

2 Answers

2001 s-10 po 452 and co265


After you replaced all these parts did you clear the ECM with a OBD II scanner or did you just leave it?

Jun 01, 2010 | 2001 Chevrolet S-10

1 Answer

Co265 ebcm motor relay circuit p/n 88982286 error code 26 where is the part located and are there photo's of this ebcm for a 2000 silverado 4x4


Hello, your EBCM is located on the frame underneath the vehicle just below the driver's seat. Sorry, I don't have a picture of it. Have you had brake work done recently?

Mar 06, 2010 | 2000 Chevrolet Silverado 1500

1 Answer

04 chevy avalanche. failed inspection. OBD11


Hi, a P0446 means Evaporative Emission Control System Vent Control Circuit Malfunction

Full details @ http://www.obd-codes.com/p0446

Feb 06, 2010 | 2004 Chevrolet Avalanche

1 Answer

Abs codes co281 & co265


the first of the two codes is for the brake light switch, the one that is under the dash attached to the brake rod and brake peddle. Not much to diag on that one, if its bad it's bad, and when it sets the code that means it's bad.
The second one is for the abs modual, it's under the truck on the drivers side. It is bolted to the top of the thing that has all of the brake lines going to it. MOST all of the time that code is set the modual is bad. It can be a little hard to get the bolts out they are torqs 20 or 25(i'm getting old). There are four of them holding down the modual. There are also a couple of connectors going to it. And some of the time it will blow the fuse for the abs under the hood(its in the underhood fues block). Make sure to clean off the modual before you pull it out. You don't want dirt getting in the solinoids for the BPMV(that's the thing it's bolted to).

Oct 20, 2009 | 1999 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

261 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...