Question about Cars & Trucks

Open Question

Mondeo 5th gear problem keeps jumping out of gear

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Problems with gear box

I had the same problem, have the clutch fitted, but ask the garage to look at your gear linkage too.

Posted on Jun 21, 2008

Ad
  • 112 Answers

SOURCE: transmission problems (gear linkage)

The gear linkages are not correctly aligned.
Is the gearbox mounting in exactly the same place as when you removed it?
Even a 1/4 inch will offset the gears.
hope this helps

Posted on Jan 26, 2009

dezwez
  • 135 Answers

SOURCE: stuck in gear.hard to change gear ford mondeo 2001

sounds like your duel mass fly wheel has given up common on these
cost a lot to do

Posted on Sep 01, 2009

planet-x
  • 232 Answers

SOURCE: MY RAV4 KEEPS JUMPING OUT OF 5TH GEAR

worn gearbox or engine mounts allowing the gearbox to move and unlatch the shift linkage from its position, or the shift linkage is mal-adjusted and not properly engaged in 5th gear at all.

There may be a knuckle joint that can be adjusted to give correct shifter operation, it may be out of adjustment. GM cars are prone to this after reversing uphill in a manual car, your Nissan may be similar. The engine moves away from the area of the shift lever and pulls the knuckle joint out further than it is supposed to be and causes the gears not to enage securely any more.

Posted on Oct 24, 2009

  • 4793 Answers

SOURCE: my 02 toyota avensis d4d keeps jumping out of 5th

the box has to come out im afraid,but do not replace the gear,just the baulk ring,as a matter of interest we used to take out the whole engine/ transmision as a unit (easier to work with on a stand.)

Posted on Apr 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can any one help me with advice on how to repair the 5th gear on my Chana 1300 Club Star? Greetings, Johan.


Replace the selector and check adjustment. Only replace the gearing if teeth are badly worn as that alone will not cause it to jump out of gear.

Aug 08, 2017 | Cars & Trucks

1 Answer

Jumps 5th gear


The synchromesh is worn on the 5th gear.
Hold it down or swap in a replacement gearbox.

Jan 19, 2014 | Ford Ranger Cars & Trucks

2 Answers

1st and 5th gear jumps out of it's position. Revers gear do's not engage gear from time to time


if this is a manual gearbox then its the indent springs in the selector rod movement inside the gearbox and this will involve removing the gearbox if i have correctly located the fault ,but without the make and model of vehicle i cannot say for certain as it could be the gearchange mechanism movement inside the cars cab and if tis cable then a outer sheaf on a cable could be loose and come out of its crimped holder

Feb 10, 2012 | Kia Rio Cars & Trucks

1 Answer

My 02 toyota avensis d4d keeps jumping out of 5th gear so can i replace 5th gear with the box still in the car ?


the box has to come out im afraid,but do not replace the gear,just the baulk ring,as a matter of interest we used to take out the whole engine/ transmision as a unit (easier to work with on a stand.)

Apr 06, 2010 | 2002 Toyota Camry

1 Answer

Jumps out of 5th gear


syncro is a little round instead of square liped

1 too many grinders usually requires a rebuild of the trans or go to auto recyclers and get a new used trans

Jan 02, 2010 | Ford Ranger Cars & Trucks

1 Answer

Mondeo wont start, makes a click sound when ignition is turned on


hi sounds like your starter motor has packed in with all the trying.. just quickly put your car in 5th gear and give it a rock this might release it if not then you gota replace it and as a must get your battery charged up so it has the correct cranking amps to turn the starter

Dec 24, 2009 | 1999 Ford Escort

1 Answer

Mondeo mk3 TDDI 2.0 90ps,x reg- clutch and gears, manual


yeh if not more sorry! does sound like the clutch

Apr 17, 2009 | 2000 Ford Focus

1 Answer

Transmission problems (gear linkage)


The gear linkages are not correctly aligned.
Is the gearbox mounting in exactly the same place as when you removed it?
Even a 1/4 inch will offset the gears.
hope this helps

Jan 26, 2009 | 2000 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...