Question about Cars & Trucks

Open Question

P1035 code o2 bank1 toyota 2.4 estima - Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 31 Answers

SOURCE: o2 sensor bank1 sensor 1

usually bank 1 sensor one is closest to the motor(guess) but you can look it up in a manual and just changing the 02 sensor is gonna fix it they are anywhere from 40 to 100 dollars hope it helps

Posted on Jul 09, 2009

Ad
  • 135 Answers

SOURCE: Where is bank1 sensor 1 (O2 sensor) of 2003 Mitsubishi Eclipse

if its a 4 cylinder it will the 02 sensor closest or if not in the exhaust manifold

Posted on Aug 05, 2009

  • 28 Answers

SOURCE: Code P0141. O2 Sensor heater circuit fault (Bank1,

It is probably the sensor before the cat. if it has a heater. The heater circuit going bad is a common problem, it does not affect the way the car runs after it warms up, it is an emission device to heat the O2 sensor up quicker than the hot exhaust gas would. It should be replaced because it will keep your check engine light on and you would not be able to pass an emission test.

Posted on Oct 12, 2009

wracefans24
  • 1985 Answers

SOURCE: problem locating the oxygen sensor for my 2000 Toyota Estima

drivers side ,sensor before converter

Posted on Jan 03, 2010

  • 1757 Answers

SOURCE: 2003 dodge caravan with fault code P1035. Is the

Is it Code P1035 or P0135?
It is the Upstream Sensor. 100 Codes ending in 30 thru 35 are dealing with the Upstream Sensor. 100 Codes ending in 36 thru 41 are dealing with the Downstream Sensor.

Let me know if this helped.....

Posted on Mar 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

02 Toyota Camry p1035 code


Code shows P1035 for Oxygen Sensor Bank 1 Sensor 1 being defective, did you turn it off with a scanner! go to any auto parts store and they will turn light off for free, auto-zone, advanced, etc, after it is turned off. drive it a few miles to recycle the code. this should help. because if the battery is disconnected to clear the code, it will not work properly for a 2000s vehicle. Hope this helps! you may have to have dealer turn it off. but check above first. Good-Day!

May 25, 2014 | Toyota Camry Cars & Trucks

1 Answer

Code number for o2 sensor voltage low


Forget to write it down?

Generic or Manufacturer?

There are 41 Generic O2 Codes

PO 131--bank 1 sensor 1
PO 137--bank1 sensor 2
PO 143--bank1 sensor 3
PO 151--bank2 sensor 1
PO 157--bank1 sensor2
PO 163--bank2 sensor 3

Nov 23, 2012 | 2009 Toyota RAV4

1 Answer

Hi, I have a 96 Jeep Cherokee with straight 6 cyclinder engine.The check engine lights on and Itook get to be put on a machine and the codes readed P0132,P0135,P0300,P0301,and P0420. Could you tell me


p132+ an O2 sensor reading is high bank1,sensor1, p135=O2 Heater circuit is bad, bank1,sensor1.

P300= Random misfires, p301 misfire cylinder1.p302 misfire cylinder2

p420 Bank1 Catalytic converter efficiency failing

What this means is that the Bank1 O2 sensor is either bad or the wiring to it is defective. Check for heat burnthrough on wires. The misfires started randomly and now pinpoint to cylinders 1 and 2.

The Catalytic converter failing because the misfires are clogging it. This can self correct once the cylinders stop misfiring.

Which messed up first is where you start solving this. Replace the O2 sensor, it is fouled out on Bank1. The heater circuit(p135) just makes it work faster and has little effect once you are underway. But high resistence in the O2(p132) means it is coated and ineffective.

There is a problem with firing #1 and #2 sparkplug. Probably the cause for the Catalytic converter plugging. A cracked coil, plug wires, sparkplugs are some causes as well as dirty fuel injectors on those 2 cylinders.

It is a cause and effect situation where 1 part fails and damages another. You need to fix the source of the problem or you will repeat th damage.

Oct 01, 2012 | Cars & Trucks

1 Answer

Where is sensor1 bank1 o2 sensor on a 95 avalon


Bank refers to the side of the engine. Bank1 is always the same side as the number one cylinder. Bank 2 is always the other side of the motor on a v-6 or v-8

Sensor refers to before or after the catalytic converter. Sensor 1 is always before the cat. sensor 2 is always after the cat.

Bank1 sensor 1 on your vehicle - since the number one cylinder is on the backside of the motor closest to the firewall the B1S1 - O2 would be in the exhaust manifold on the back side of the engine before the catalytic converter.

Sep 19, 2011 | 1995 Toyota Avalon

2 Answers

2001tiburoncomputor codes, po136 & 141 what do they refer to.


P0136 = Oxygen Sensor Circuit Malfunction (Bank1, Sensor2)
P0141 = Oxygen Sensor Heater Circuit Malfunction (Bank1, Sensor2)

CHECK WIRING BEFORE REPLACING SENSORS

If 4 cylinder engine, there are only two O2 Sensors - Sensor 1 is on top, Sensor 2 is at the bottom

If 6 cylinder, there are four (4) O2 sensors (Bank1, Sensor2 is on the firewall side of this engine and is referred to as the 'DOWNSTREAM' sensor (the one AFTER the Catalytic Converter)

Aug 25, 2011 | Hyundai Tiburon Cars & Trucks

1 Answer

2005 toyota tacoma 2.7 code p0037 replace rear 02 and computer code keep coming back.


P0037 - O2 Oxygen Sensor Circuit High Voltage (Bank1, Sensor2)

The Heated Oxygen Sensor (2) located rear of catalytic converter produces an output signal relative to oxygen storage capacity of catalytic converter. Ho2S 2 signal is less active than signal produced by front oxygen sensor. This code sets when HO2 Sensor voltage is greater than 999 mV for more than 2 minutes (time depends on model. Could be as high as 4 minutes)

Symptoms: There may be no noticeable symptoms except for MIL illumination. Possible high fuel pressure can over rich the system.

Causes: A code P0138 may mean that one or more of the following has happened:
* Faulty O2 sensor
* Short to battery voltage in O2 sensor signal circuit
* High fuel pressure (not as likely)


Here are some potential solutions:
* Replace O2 sensor
* Repair short to battery voltage in o2 sensor signal circuit

If you replaced the O2 sensor, then its possible that you have some electrical problem there; reset the codes first, and if this come on again, check in this link TSB P0037 electrical diagnostic procedure.

Keep us updated.

Jan 27, 2011 | 2005 Toyota Tacoma

2 Answers

Check enegine light stay s on all the time, here are the codes im getting, if someone could tell me how to fix these that would be great. p0155 p0141 p0136 p0443 p1451 p0135 p0161 p1409


P0155: O2 Sensor heater Circuit Malfunction (bank2 ) Sensor 1.

P0141: O2 Sensor heater Circuit Malfunction (bank1 ) Sensor 2.

P0135: O2 Sensor heater Circuit Malfunction (bank1,Sensor1)

P0136: O2 Sensor Circuit Low voltage (bank1) Sensor 2.

P0443 : Evaporative Emission control System Purge control valve.

P1451: Eavporative Control System Canister vent solenoid Circuit Malfunction.

P0161: O2 Sensor Circuit Low voltage (bank2,Sensor2)

P1409: Electronic Vacuum Regulator (EVR) control circuit malfunction.

change the O2 sensors first,Then check the the EGR Vacuum regulator for any Malfunction. Good luck

Jan 14, 2011 | Ford Mustang Cars & Trucks

1 Answer

Engine light stays on after changing 02 sensor on my 2000 toyota tundra code read o2 sensor


did u change the right o2 sensor there is 2 sensors on bank1 and 2 on bank2.....upstream and down stream.....i had the same prob i changed the o2 senser to the other side to check and make sure it was the o2 senser....it took 4 o2 sensors before i got 1 that finally worked nd yes i was buying them brand new.....so change sides with it nd see if the code changes sides....and did u reset it with the code machine when u put the new 1 in?

Mar 28, 2010 | 2000 Toyota Tundra

1 Answer

Check engine light came on. giving codes P1035 and P1055. whats wrong with it. it it a 2004 jeep grand cherekee Laredo


I'm sorry I don't have more for you. I could not locate a dtc for "P1055", but did find some info for "P1035". It is for the bank 1, sensor 1 O2 sensor heater circuit. I would check fuse nos. 16 and 34 in the underhood power dist. center first. Next I would look at the connections to the O2 sensors, you should have 4 total. The catalytic convertors, yes there are two, are connected directly to the exhaust manifold, which is a split manifold. Cylinder nos. 1-3 empty into the front section while cylinders 4-6 empty into the rear section. There should be an O2 sensor before each convertor and after each convertor.

Nov 30, 2009 | 2004 Jeep Grand Cherokee

2 Answers

Codes p1456&p1035


Hi,

P1456 Evaporative Emission Control System Leak Detected (Fuel Tank System)

I didn't see your p1035 code, but I found a good site for your reference:

http://www.engine-light-help.com/honda-check-engine-light.html

Hope this helps... Good luck!

Aug 27, 2009 | 1998 Honda Civic

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...