Question about Cars & Trucks

Open Question

2004 kia rio check engine code p044

Evaporative emission purge solenoid control open

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jpstuhr
  • 49 Answers

SOURCE: Troubleshooting code: P0442

Here ya go

6b631d6.jpg

Posted on Feb 11, 2009

emissionwiz
  • 75066 Answers

SOURCE: CODE P0441

most likely the carbon canister fresh air vent is plugged with a spider web or dirt, the other option is the electric purge control solenoid is defective.

Posted on Apr 02, 2009

  • 84 Answers

SOURCE: My 2003 Kia Spectra has Diagnostic codes: P1404 & P0444.?.?

the purge valve i believe is located near your gas tank unless theyve moved it i should look like a little canister cyclinder shaped. both codes could be set off by the same problem. try replacing the valve.

Posted on May 05, 2009

  • 76 Answers

SOURCE: What is EVAPORATIVE EMISSION...Purge Flow?? Mitsubishi Mirage?

This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. Try changing the gas cap first then check the rubber hoses that are visble on top of the engine. Vote "Yes" for me!

Posted on Aug 18, 2009

ZJLimited
  • 17970 Answers

SOURCE: code po449 States "Evaporative emission control

Check engine P codes. GM uses an EVAP solenoid that is located under most vehicles near the gas tank and connects to the charcoal filter can. Codes can be set and will drive you crazy trying to figure out if you have a bad gas cap, broke lines---this is where they try to get you to do a smoke test, or you just think the vehicle is no good.

Relax, it is usually an easy fix and one GM has known about for years but continues to make easy money off people who cannot do basic maintenance. Now one code that comes up is usually P0449, along with maybe a warning to check the gas cap to see if it is on tight. Chevrolet will gladly read this code out for you for around $98.00 and then fix it for another around $100.00 which includes the EVAP part which if you buy at their parts dept. will cost you $32.00 and my dealership parts man told me they sell one a day! It is easy money for them and obviously a defective part they keep using for the last 10 or 15 years but hey, its money in their pocket. Here is how to fix it with ONE single common screwdriver!

Get under the vehicle after putting on the parking brake and if you a little hefty, then removing the spare tire on the some vehicles will give you lots more room. The EVAP solenoid is easy to spot near the gas tank and it has one electric connector which disconnects by releasing the plastic clip and pulling the connector out. It also has ONE air line connected which goes to the charcoal cannister which also can be removed with the one screwdriver. The whole EVAP solenoid and air can can be removed with the screwdriver which makes it easier to unpolug the electric and air line. Get a replacement from the dealer as they certainly are familar with this part as they sell LOTS of them. Then just go under and plug the new one in and the problem is solved. Now if you do not have a tool to reset the codes, try the local parts places as most of them will do a reset for you. If you do not have someone to do it, it can be done simply be removing the RED, positive lead off the battery and wait a minute and then plug it back in. The codes are reset but of course now you have to reset the radio and clock stuff.

Hope helps (remember to rate this answer).

Posted on Nov 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a truck that popped up a P0443 code up and I've been trying to see what it is so I can get it fixed thank yo


P0443 - Evaporative Emission Control System Purge Control Valve Circuit Malfunction

Possible causes: - Faulty Evaporative Emission (EVAP) Purge Solenoid Control
- Evaporative Emission (EVAP) Purge Solenoid Control harness is open or shorted
- Evaporative Emission (EVAP) Purge Solenoid Control circuit poor electrical connection

When is the code detected? An improper voltage signal is sent to Engine Control Module (ECM) through the valve.
Possible symptoms: - Engine Light ON (or Service Engine Soon Warning Light)
P0443 Description: The Evaporative Emission System (EVAP) canister purge volume control solenoid valve uses a ON/OFF duty to control the flow rate of fuel vapor from the EVAP canister. The EVAP canister purge volume control solenoid valve is moved by ON/OFF pulses from the Engine Control Module (ECM). The longer the ON pulse, the greater the amount of fuel vapor that will flow through the valve.

P0443 Information for specific makes: P0443 ACURA
P0443 CHRYSLER
P0443 DODGE
P0443 FORD
P0443 HONDA
P0443 INFINITI
P0443 ISUZU
P0443 JEEP
P0443 KIA
P0443 LAND-ROVER
P0443 LEXUS
P0443 MAZDA
P0443 MERCEDES-BENZ
P0443 MITSUBISHI
P0443 NISSAN
P0443 TOYOTA
P0443 Evaporative Emission Control System Purge Control Valve Circuit...

Jun 03, 2015 | Cars & Trucks

1 Answer

What code is po443


ossible causes
- Faulty Evaporative Emission (EVAP) Purge Solenoid Control
- Evaporative Emission (EVAP) Purge Solenoid Control harness is open or shorted
- Evaporative Emission (EVAP) Purge Solenoid Control circuit poor electrical connection
help.jpg What does this mean?
When is the code detected?
An improper voltage signal is sent to Engine Control Module (ECM) through the valve.
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
P0443 Description
The Evaporative Emission System (EVAP) canister purge volume control solenoid valve uses a ON/OFF duty to control the flow rate of fuel vapor from the EVAP canister. The EVAP canister purge volume control solenoid valve is moved by ON/OFF pulses from the Engine Control Module (ECM). The longer the ON pulse, the greater the amount of fuel vapor that will flow through the valve.

Jul 21, 2014 | 2000 Mercury Mountaineer

1 Answer

Toyota echo won't start code 440 441 446


Error Code: P0440
Fault Location:
Evaporative Emission (EVAP) System - Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Soution:
Check Evaporative Emission (EVAP) System Sealing.
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .

Error Code: P0441
Fault Location:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Solutions:
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Perform Output Test.
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .
Check Evaporative Emission (EVAP) Canister.
Perform Basic Setting.
Check Pipes between Tank Breathing and Throttle Body.

Error Code: P0446
Fault Location:
Evaporative Emission (EVAP) System, Vent Control - Circuit Malfunction
Possible Cause:
Wiring harness.
Evaporative emission (EVAP) canister purge valve.
Engine control module (ECM).

Feb 25, 2013 | 2002 Toyota ECHO

1 Answer

Evaporative Emission Control System Purge Control Valve Circuit Opeat's your problem?


Possible causes- Evaporative Emission (EVAP) Purge Solenoid Control harness is open or shorted
- Evaporative Emission (EVAP) Purge Solenoid Control circuit poor electrical connection
- Faulty Evaporative Emission (EVAP) Purge Solenoid Control

Read more: http://engine-codes.com/p0444.html#ixzz296gIeNzB

Oct 12, 2012 | 2001 Mercedes-Benz ML 320

1 Answer

P044 EVAPORATIVE EMISSION CONTROL SYSTEM LEAK / DETECTED SMALL LEAK ON A 2004 CHEVY AVEO


The most likely causes of this code are:
A Leak in the System
Faulty Purge Solenoid (This is the valve that lets the fumes into the engine)
Faulty or loose fuel cap
Faulty or Loose NVLD (This is the sensor that senses whether the system is working or not)
The first thing to try is re-installing your fuel cap as this can cause this code and is an easy fix. If you suspect the cap might be bad, then you might want to just replace it. You can also check for any loose or damaged hoses under your hood. They can cause this type of code.( p0440 ). good- day !

Jul 19, 2011 | Chevrolet Chevy Cars & Trucks

1 Answer

My 2004 Kia Optima has a code P0443 and I know what it is. There's a hole where air is getting in and I need to know how to find it


Hi, 443 is not a leak--it a purge valve malfunction. Usually the solenoid packs up, but it could be wiring or the connector. You need to disconnect the valve and apply battery voltage to it to see if the solenoid will click. If it clicks, the problem is wiring. If not, replace the purge valve/solenoid. Please let me know if you have questions.

jturcotte_1720.gif

jturcotte_1719.gif



P0443 - Evaporative Emission Control System Purge Control Valve Circuit OBD-II Trouble Code Technical Description

Evaporative Emission Control System Purge Control Valve Circuit
What does that mean? The Evaporative Emissions System (EVAP) allows fumes from the gas tank to enter the engine to be burned, rather than vented into the atmosphere as an emission. The purge valve solenoid is supplied switched battery voltage. The ECM controls the valve by operating the ground circuit, opening the purge valve at specific times allowing these gasses to enter the engine. The ECM monitors the ground circuit as well, watching for faults. When the purge solenoid isn't activated, the ECM should see a high voltage on the ground circuit. When the solenoid is activated, the ECM should see the ground voltage pulled low, close to zero. If the ECM doesn't see these expected voltages, or senses an open in the circuit, this code is set.
Potential Symptoms P0443 trouble code symptoms could be just an malfunction indicator lamp (MIL) illumination. There may be no drivability problems at all. But, it's also possible to have a lean condition or a rough running engine if the purge valve is stuck open. Usually though, these symptoms are accompanied by other EVAP codes. Another symptom may be excessive pressure in the gas tank in the form of a "whooshing" sound when the cap is removed, indicating a purge valve that isn't working at all or stuck closed.
Causes To cause a P0443, there has to be a problem with the purge control CIRCUIT, not necessarily the valve. Usually they are a unit housing the valve and the solenoid as an assembly. Or it could be comprised of a separate solenoid with vacuum lines to a purge valve. That said, it could be any of the following:

  • Bad purge solenoid (internal short or open)
  • Wiring harness chafing or rubbing another component causing short or open on control circuit
  • Connector worn, broken or shorted due to water intrusion
  • Driver circuit inside powertrain control module (PCM) is bad
Possible Solutions 1. Using a scan tool, command the purge solenoid to activate. Listen or feel for a clicking coming from the purge solenoid. It should click once, or on some models it may click repeatedly.
2. If it doesn't click with scan tool activation, unplug the connector and examing the solenoid and connector for damage, water, etc. Then check for battery voltage on the feed wire with the key on. If you have battery voltage, then ground the control side manually using a jumper wire and see if the valve clicks. If it does, then you know the solenoid is working properly but there is a problem with the control circuit. If it doesn't click when you manually ground it, replace the purge solenoid.
3. To check for a problem on the control circuit (if the solenoid tests okay and you have voltage to the solenoid) plug the solenoid back in and remove the control circuit (ground) wire from the ECM connector (If you're unsure how to do this, do not attempt). With the ground wire removed from the ECM, turn the key on and then manually ground the Purge valve control wire. The solenoid should click. If it does, then you know there is no problem with the control wire to the solenoid and there is a problem with the ECM purge solenoid driver circuit in the ECM. You'll need a new ECM. However if it doesn't click, then there must be an open in the wiring between the ECM and and the solenoid. You must find it and repair it.

May 16, 2011 | Kia Optima Cars & Trucks

2 Answers

Code says evaporator purge solenoid


Which code specifically? Do not assume you need a new solenoid. Our recommendation will depend on the specific code and some troubleshooting results. I usually recommend checking over all the EVAP vacuum lines and the gas cap too whenever there is a purge valve code. Check the vacuum lines at the cannister in the left rear bumper. I will paste info on the purge solenoid below.

P0440 Evaporative emission (EVAP) system - malfunction

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


P0441 Evaporative emission (EVAP) system - incorrect flow detected

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


P0442 Evaporative emission (EVAP) system - small leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


P0443 Evaporative emission (EVAP) canister purge valve - circuit malfunction

Possible causes: Wiring, EVAP canister purge valve, ECM


P0444 Evaporative emission (EVAP) canister purge valve -open circuit

Possible causes: Wiring open circuit, EVAP canister purge valve, ECM


P0445 Evaporative emission (EVAP) canister purge valve -short circuit

Possible causes: Wiring short circuit, EVAP canister purge valve, ECM


P0450 Evaporative emission (EVAP) pressure sensor - circuit malfunction

Possible causes: Wiring, EVAP pressure sensor, ECM


P0455 Evaporative emission (EVAP) system - large leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


P0456 Evaporative emission system - very small leak detected

Possible causes: Mechanical fault, hose connection(s), EVAP pressure "sensor


P0457 Evaporative emission system - leak detected (fuel cap loose/off)

Possible causes: Mechanical fault, hose connection(s), EVAP pressure sensor


P0458 Evaporative emission system, purge control valve -circuit low

Possible causes: Wiring short to earth, EVAP valve


P0459 Evaporative emission system, purge control valve -circuit high
Possible causes: Wiring short to positive, EVAP valve


Evaporative Emission Purge Solenoid

Description & Operation
The duty cycle EVAP canister purge solenoid (DCP) regulates the rate of vapor flow from the EVAP canister to the intake manifold. The Powertrain Control Module (PCM) operates the solenoid.
During the cold start warm-up period and the hot start time delay, the PCM does not energize the solenoid. When de-energized, no vapors are purged. The PCM de-energizes the solenoid during open loop operation.
The engine enters closed loop operation after it reaches a specified temperature and the time delay ends. During closed loop operation, the PCM cycles (energizes and de-energizes) the solenoid 5 or 10 times per second, depending upon operating conditions. The PCM varies the vapor flow rate by changing solenoid pulse width. Pulse width is the amount of time that the solenoid is energized. The PCM adjusts solenoid pulse width based on engine operating condition.
Removal & Installation
The duty cycle evaporative (EVAP) canister purge solenoid is located in the engine compartment near the brake master cylinder.

  1. Disconnect electrical connector at solenoid.
  2. Disconnect vacuum lines at solenoid.
  3. Lift solenoid slot from mounting bracket for Removal & Installation.

To Install:
  1. Position solenoid slot to mounting bracket.
  2. Connect vacuum lines to solenoid. Be sure vacuum lines are firmly connected and not leaking or damaged. If leaking, a Diagnostic Trouble Code (DTC) may be set with certain emission packages.
  3. Connect electrical connector to solenoid.
Purge solenoid location:

jturcotte_65.gif
EVAP cannister location:
jturcotte_66.gif

Nov 05, 2010 | 2000 Jeep Grand Cherokee

2 Answers

I checked the codes and one comes up its po446. i dont under stand what it mean so i cant fix it to get the light to go out.


P0446 Evaporative Emission System Vent Control Circuit.
The following are descriptions of all Evaporative possible codes:

P0441 Evaporative Emission System Incorrect Purge Flow
P0442 Evaporative Emission System Leak Detected (small leak)
P0443 Evaporative Emission System Purge Control Valve Circuit
P0444 Evaporative Emission System Purge Control Valve Circuit Open
P0445 Evaporative Emission System Purge Control Valve Circuit Shorted
P0446 Evaporative Emission System Vent Control Circuit
P0447 Evaporative Emission System Vent Control Circuit Open
P0448 Evaporative Emission System Vent Control Circuit Shorted
P0449 Evaporative Emission System Vent Valve/Solenoid Circuit
P0450 Evaporative Emission System Pressure Sensor/Switch
P0451 Evaporative Emission System Pressure Sensor/Switch Range/Performance
P0452 Evaporative Emission System Pressure Sensor/Switch Low
P0453 Evaporative Emission System Pressure Sensor/Switch High
P0454 Evaporative Emission System Pressure Sensor/Switch Intermittent
P0455 Evaporative Emission System Leak Detected (large leak)
P0456 Evaporative Emission System Leak Detected (very small leak)
P0457 Evaporative Emission System Leak Detected (fuel cap loose/off)
P0458 Evaporative Emission System Purge Control Valve Circuit Low
P0459 Evaporative Emission System Purge Control Valve Circuit High
---
At least the cap isn't loose for the gas tank.

I would clear the code with an OBD-II Scanner 'erase code' button, and see how long it takes for it to come back.

Aug 06, 2010 | 1996 GMC Jimmy

2 Answers

Check Engine Light


Code P0442 means Evaporative Emission Control System Leak Detected-(small leak). Most times that code is set if you removed the gas cap while the engine was running. If not, you could have a bad gas cap. It's minor in the grand scheme of things, but to be on the safe side, replace the gas cap, have the code cleared, and drive the car for a day or two. If the light stays off, problem solved.

Aug 15, 2009 | 2003 Kia Spectra

2 Answers

P0441 EVAP Control System Incorrect Purge Flow


Error Code: P0441
Fault Location:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Evaporative Emission (EVAP) Canister Purge Regulator Valve faulty/jammed.
Evaporative Emission (EVAP) Canister Purge Solenoid Valve faulty/jammed.
Evaporative Emission (EVAP) Canister Sealing faulty.
Pipes between Tank Breathing and Throttle Body leaky/blocked.
Hose connection(s).
Intake leak.
Possible Solutions:
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Perform Output Test.
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve.
Check Evaporative Emission (EVAP) Canister.
Perform Basic Setting.
Check Pipes between Tank Breathing and Throttle Body.
VSV connector near air filter box disconnected.

Jun 15, 2009 | 1996 Chevrolet Monte Carlo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...