Question about Cars & Trucks

1 Answer

What is a transmission govenor - Cars & Trucks

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 2,101 Answers

What kind of car

Posted on Nov 07, 2012


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Transmission will not engage

proper fluid amount or possibly faulty modulator on side of transmission or govenor sticky

Dec 18, 2013 | Cars & Trucks

1 Answer

700r4 chevy overdrivewill not upshift from first to second and so on all i have is first and reverse

Either the detent cable is broken , disconnected ,or out of adjustment and is putting the transmission into fail safe or the govenor gear is apple cored( round cover on left rear of transmission).

May 03, 2011 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

I have a 98 dodge ram 2500 5.9 4x4 automatic with o/d will not shift out of low untill a mile or two down road then does fine, had a service done and foung half of a clutch band in pan with metla shaving...

Aluminum metal shavings are very normal for this transmission if the pan has never been off.What do you mean by "clutch band".This unit has 4 sets of clutches 2 bands and 2 rollers clutches.I would suspect a bad govenor pressure sensor and or solenoid by the symptoms you describe.With a scan tool you can look at govenor pressure(actual)and desired govenor pressure.Govenor pressure should be at 0 sitting still and should increase with road speed( example 22 mph=22psi). Let me know if I can help.

Feb 13, 2011 | 1999 Dodge Ram

2 Answers

Transmision is not changing gears what could that be?

Stripped govenor gear possibly. Knock off the round cover on the left rear of transmission and pull the governor out, If nylon gear on the end is broken or apple cored replace the gear. Be very careful if you decide to replace govenor the are small differences that make big changes to shift pattern. Also check to make sure the cable that connects to throttle lever from transmission is not broken.

Jan 19, 2011 | 1991 GMC S-15 Jimmy

2 Answers

I was driving my 90 nissan sentra and. It started to rev up it doesn't want to shift u can drive bout 25 mph I think its stuck in 1st gear

it actually sounds as if the high clutches in trans is slipping you have to have a pressure test done but be prepared to replace trans

Jan 15, 2011 | 1990 Nissan Sentra

1 Answer

Trcansmission govenor

It is on the transmission, towards the output housing. Normally close to the pan on the side. It should have a round steel cover held on with either a metal clip or a few bolts.

May 31, 2010 | 1999 Dodge Ram

1 Answer

Transmission solenoid

could be the govenor soleniod or gov. transducer i have replaced many in trucks and suvs with the 42,46,47,48,re transmissions

Nov 23, 2009 | 1999 Dodge Ram

1 Answer

What shift from 1st to 2nd

I am asumin your saying that the transmission wont shift from 1st to 2nd gears. What this could be is either a low fliuid problem or an internal failure of the transmission. I believe the transmission govenor on those units can cause a bad hifting problem. Looks like your set for a tranny rebuild

Aug 28, 2009 | 1999 Dodge Durango

1 Answer

1987 s10 pickup transmission leaking. two spots , Governor cover and from some sort of cable going from the transmission to the throttle body

The govenor cover has an o-ring seal. No problem, just be sure NOT to let the govenor fall out. Remove the cover with a screwdriver by tapping it outward with a hammer, gently. The throttle valve cable has a rubber seal, you can get from any trans shop. Unhook it from the top/throttle body first. Leave it mounted in the brackets. Then remove the bolt holding it into the trans, pull up and un hook the throttle valve linkage. Be sure to reinstall this in the reverse order. If when you go to hook it back up top pull the cable. You should feel spring tension on the cable if so then you have it right. Good Luck

May 16, 2009 | 1987 Chevrolet S-10 Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides