Question about 1998 Toyota Tacoma

Open Question

How to replace front shocks on 1998 toyota tacoma

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: front axle - front drive shaft Toyota tacoma 1998 4x4

more than like have a broken axle shaft, un hook the rear drive shaft and put it in 4wd if it wont move then you know you got a broken axle shaft or spider gears broke in the pumpkin

Posted on Dec 09, 2008

c17hydro
  • 2984 Answers

SOURCE: replacing front struts

Okay....here is the steps first....and then the directions on how to use the tools:

  1. Raise and properly support the vehicle.
  2. Remove the front wheel.
  3. Detach the shock absorber lower mount by removing the two bolts.
  4. Remove the retainer nut, retainer, cushion and shock absorber.
  5. Detach the cushion retainer from the shock absorber.
  6. Compress the coil spring with a commercially available spring compressor.
  7. Detach the stabilizer bar.
  8. Support the upper suspension arm and steering knuckle securely.
  9. Remove the cotter pin.
  10. Loosen and remove the nut.
  11. Using a ball joint removal tool, detach the lower ball joint from the lower control arm.
  12. Loosen the suspension arm set bolt.
  13. Remove the suspension arm set bolt nut.
  14. Remove the nut from the strut bar front set bolt.
  15. Pull out both set bolts.
  16. Remove the lower suspension arm and coil spring. To install:
  17. Installation is the reverse of removal. Note the following torque specifications:
    1. Strut bar front set bolt: 221 ft. lbs. (300 Nm)
    2. Lower suspension arm set bolt: 148 ft. lbs. (200 Nm)
    3. Lower ball joint nut: 80 ft. lbs. (110 Nm)
    4. Lug nuts: 83 ft. lbs. (110 Nm).

Posted on May 13, 2009

BillB-SA
  • 2761 Answers

SOURCE: thermostat replacement in a 1998 toyota tacoma

You're going to lose some coolant, so have a bucket or other container ready. Follow the upper radiator hose to the point where it's connected to the engine. The hose is clamped to a metal housing which is bolted to the engine. Remove the bolts (not the hose) and lift the housing to expose the thermostat (may require a little prying with a screwdriver or similar tool). Note how the old thermostat is fitted (which end is up), lift it out of the engine, and then remove all traces of gasket from the housing and the engine. Install the new thermostat and gasket, replace the bolts, add coolant as necessary, and you're done.

Posted on Jan 04, 2010

arauzvictor1
  • 466 Answers

SOURCE: how do i remove the manuel clutch to a 1998 tacoma

If you want to change the "Remove clucht trasmision bars front and rear, remove the cylinder in the booth attendant said you have to remove the gear-change broadcasts have jack-remove the bracket that supports the transmission back-to remove the exhaust pipe - Put the jack, remove the screws that attach the transmission with the engine off, remove the transmission clucht well ... You have to ensure the transmission on the jack will not fall

Posted on Jan 11, 2010

  • 13 Answers

SOURCE: How do I replace the parking lights on the front

1. Open the hood.
2. Remove the one screw holding the side marker housing inside the engine compartment about half inch from fender edge.
3. Pull the side marker and unplug electrical connector.
4. Remove bulb holder counterclockwise.
5. Pull bulb straight out.
6. Reinstall in reverse order.

Posted on Apr 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing front struts on 2wd toyota tacoma


Undo the nuts under hood remove brake caliper remove lower ball joint and tie rod end,remove brake pipe.

Jul 30, 2014 | 2008 Toyota Tacoma

1 Answer

Replacing front struts on a 2007 toyota tacoma


REALLY HARD PROJECT, TAKE IT TO SEARS, IT WILL ALSO NEED FRONT ALLIGNMENT

Jul 25, 2010 | 2007 Toyota Tacoma

1 Answer

Do you need a sring compressor to replace the front shocks on a toyota tacoma


No, this truck has shocks in the front, you only need a spring tool if there were struts,youll have no problems doing it yourself ,good luck.

Jun 01, 2010 | 2002 Toyota Tacoma

1 Answer

How do i remove the manuel clutch to a 1998 tacoma


If you want to change the "Remove clucht trasmision bars front and rear, remove the cylinder in the booth attendant said you have to remove the gear-change broadcasts have jack-remove the bracket that supports the transmission back-to remove the exhaust pipe - Put the jack, remove the screws that attach the transmission with the engine off, remove the transmission clucht well ... You have to ensure the transmission on the jack will not fall

Jan 11, 2010 | 1998 Toyota Tacoma

1 Answer

98 toyota tacoma tipped on the left side


the weak spring is making it tip. also you say the other shock is leaking fluid. you need to replace both shocks and springs, the seem to have been worn down, there is no fix other than using spring blocks to boost up the saging side, but i would recommend replacing it all.

Nov 30, 2009 | 1998 Toyota Tacoma

1 Answer

Where can I find the chassis number on my 1998 Toyota Tacoma?


Almost all vehicle numbers are on the door or on the car where the door latches when it shuts open the door and you should be able to find the specs. there is also more info under the hood. open hood and look right on the front. there will b engine specs and belt diagram.

Sep 26, 2009 | 1998 Toyota Tacoma

1 Answer

Replacing front struts


Okay....here is the steps first....and then the directions on how to use the tools:

  1. Raise and properly support the vehicle.
  2. Remove the front wheel.
  3. Detach the shock absorber lower mount by removing the two bolts.
  4. Remove the retainer nut, retainer, cushion and shock absorber.
  5. Detach the cushion retainer from the shock absorber.
  6. Compress the coil spring with a commercially available spring compressor.
  7. Detach the stabilizer bar.
  8. Support the upper suspension arm and steering knuckle securely.
  9. Remove the cotter pin.
  10. Loosen and remove the nut.
  11. Using a ball joint removal tool, detach the lower ball joint from the lower control arm.
  12. Loosen the suspension arm set bolt.
  13. Remove the suspension arm set bolt nut.
  14. Remove the nut from the strut bar front set bolt.
  15. Pull out both set bolts.
  16. Remove the lower suspension arm and coil spring. To install:
  17. Installation is the reverse of removal. Note the following torque specifications:
    1. Strut bar front set bolt: 221 ft. lbs. (300 Nm)
    2. Lower suspension arm set bolt: 148 ft. lbs. (200 Nm)
    3. Lower ball joint nut: 80 ft. lbs. (110 Nm)
    4. Lug nuts: 83 ft. lbs. (110 Nm).

May 13, 2009 | 1998 Toyota Tacoma

2 Answers

Where is the horn relay on a 1998 toyota tacoma


left of steering column almost behind fuse box way at the top you have to stick your head under there with a flash light to see it but it's there.

Mar 29, 2009 | 1998 Toyota Tacoma

1 Answer

Starter will not turn off, 1998 toyota tacoma


Either the starter has failed or you have a bad ground. I would say starter.

Jan 09, 2009 | 1998 Toyota Tacoma

Not finding what you are looking for?
1998 Toyota Tacoma Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...