Question about 2003 Ford Escort

2 Answers

My ignition is damaged but car turns over **** wont start

My escourts ignition was damaged now the vehicle wont run, all though it still turns over the engine what could the problem be and no fuel reaches the intake.

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 404 Answers

If the engine is stripped down to just starter motor and crank it will still turn over,so that shows the starter wire is ok,check for spark check for fuel first

Posted on Jan 05, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,692 Answers

I would guess that the 12 volts supplied to the fuel pump comes for the damaged ignition and is no longer getting the 12 volts to turn it on. Seems reasonable to me..

Posted on Jan 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

4 3 vortec v6 fuel pressure problem


If you have no fuel pressure, then that is definitely where your problem is. When you turn the ignition on, the fuel pump should run for about 1.8 seconds and build about 55-60 psi of fuel pressure. If you turn the key to the run position and don't hear the pump run, you need to trace back to why it is not coming on. Make sure there are no security issues present. Fuel pressure can be checked by installing a fuel pressure gauge to the schrader valve (it looks like a tire valve) which is located on the fuel supply line right where the fuel line connects to the spider system. Replacing the heads should not affect the starting of the vehicle in terms of before and after provided everything has been installed and hooked back up correctly. Make sure all connections are tight and pay close attention to the ground wires. There is an important ground that goes from the back of the left head to the firewall. If the battery went dead during the repair and a charger was connected with the ignition on, computer damage may have resulted. If you determine that fuel pump issues are present, make sure you examine all of the electrical aspects before replacing the pump. Even though fuel pump failures are common on these vehicles, they are expensive and often not the cause of a fuel supply problem.

Apr 23, 2014 | 1998 Chevrolet Blazer

1 Answer

My stater turns on without turnning the ignition switch


you should replace the ignition switch. I had that problem with one of my vehicles. replaced the switch and lock and it worked just fine after that. Have them check the starter though because having it keep running like that can do damage to the starter itself

Apr 24, 2012 | 1993 Toyota Celica

1 Answer

My key wont start my van it wont turn over i got a 2003 dodge caravan


make sure there isnt damage to the key is it the only key to vehicle try other key if you have one there may be damage to ignition if it isnt key replace ignition if so

Feb 11, 2011 | 2003 Dodge Caravan

1 Answer

Vehicle cranks but wont start has good fire but no fuel pressure theft light is flashing car has not run in over a year ? what do i do to get the theft light to go out?


Turn ignition to run not start,count to 5,turn off key. Repeat this three times. Try to start vehicle. If its starts you are done. If not you will need to repeat turn ignition on count to 5 then turn off, 3 more times On the fourth time leave key in the run position for 10 minutes. Then turn key off & start vehicle.

Dec 14, 2010 | 1998 Ford Expedition

1 Answer

Chevy cavalier wont start randomly! makes one click and a humm sound my lights come on the radio comes on but the car just wont start, ive had battery replaced along with the ignition switch, fuel pump,...


Ok then, from your description and the
make/model/year of the car you have there,
it appears you've reset the VATS.

The car's security immobilizer
reader at the key switch
does not recognize the coded
chip in the ignition key any longer.

You can try to put the key
in the ignition, turn to the on position &
wait at least 10 min like that.
(Do not turn off the key switch before
10 minutes as elapsed!)

Once done, the key is re-programmed and
should allow the fuel injectors to work again.
The car would start now if corrected.

In some cases, the VATS (GM'S VEHICLE ANTI THEFT SYSTEM)
will re learn the code this way, and will then
allow the restart, however if this does not work,
then you can simply tow it to any GM vehicle dealer
to have the service department re code it.

There is a permanent solution though.
Adding the PLJX Self learning Bypass module (59.95)
will bypass the PASSLOCK system in your vehicle
for good. See this at www.PASSLOCK2.com

Good luck I hope method 1 does the trick!

Here is the 30 min relearn:

Ignition keys relearn takes about 30 min to do. 30-Minute Learn Procedure 1. Turn ON the ignition, with the engine OFF. 2. Attempt to start the engine, then release the key to ON; the vehicle will not start. 3. Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF. 4. Turn OFF the ignition switch, and wait 5 seconds. 5. Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes. The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle. 6. Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password. 7. With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles. Without a scan tool you may have momentary starter interruptions while history clears itself.

Dec 22, 2009 | 2003 Chevrolet Cavalier

1 Answer

2005 ignition switch


Good day;
The following is the removal of the switch
1. remove the steering column trim covers.
2. disconnect the ignition switch harness connector.
3. turn the switch to the run position

IMPORTANT THE IGNITION SWITCH MUST BE IN THE RUN POSITION DURING REMOVAL IN ORDER TO AVOID DAMAGE TO THE IGNITION SWITCH.

4. remove the switch screws
5. remove the ignition switch from the steering column

if the ignition switch is replaced and a learn procedure is not performed the engine will crank but not start or will start and stall immediately.

30 minute learn procedure
1. turn ON the ignition with the engine OFF
2. attempt to start the engine then release the key to ON. the vehicle will not start
3. observe the SECURITY telltale. after approx 10 min the telltale will turn OFF
4. turn OFF the ignition and wait 5 seconds
5 repeat steps 1-4 two more times for a total of 3 cycles (30 min) the vehicle is now ready to relearn the PASSLOCK sensor data code and or passwords on the next ignition switch transition from OFF to CRANK.

IMPORTANT: THE VEHICLE LEARNS THE PASSLOCK SENSOR DATA CODE AND OR PASSWORD ON THE NEXT IGNITION SWITCH TRANSITION FROM OFF TO CRANK YOU MUST TURN THE IGNITION OFF BEFORE ATTEMPTING TO START THE VEHICLE.

6.start the vehicle the vehicle has now learned the passlock and or password
7. if you have a scan tool clear any codes if needed or disconnect the battery for 30 sec. the history DTC will self clear after 100 ignition cycles.

hope this helps

Cheers

Jul 13, 2009 | 2008 Chevrolet Cobalt

1 Answer

2003 ford winstar only key broke in the ignition so i replace the the ignition and reprogramed brainbox however vehicle anti theft light keeps blinking when vehicle is on and off


the anti-theft light is supposed to blink when the car is locked to show the system is armed.

Does it flash while driving?

Principles of Operation
The PATS uses a specially encoded ignition key. Each encoded ignition key contains a permanently installed electronic device called a transponder. Each transponder contains a unique electronic identification code out of over 18 billion, billion combinations.
The passive anti-theft system (PATS), also known as SecuriLock ®, uses radio frequency identification technology to deter a driveaway theft. This system is known as Securilock® in North America, Safeguard® in the U.K., and PATS in Continental Europe. Passive means that it does not require any activity from the user.
The SecuriLock® System (PATS) is not compatible with aftermarket remote start systems, which allow the vehicle to be started from outside the vehicle. These systems may reduce the vehicle security level, and also may cause no-start issues. If equipped the remote start system must be removed before investigation of PATS-related, no-start issues.
Each encoded ignition key must be programmed into the vehicle's powertrain electronic control (PCM) before it can be used to start the engine. There are special diagnostic repair procedures described in this section that must be carried out if a new encoded ignition key is necessary.
This system contains a new feature named Unlimited Key Mode. This feature allows a customer to program more than eight keys to the vehicle if they request it. Each vehicle in Unlimited Key Mode is set up with a special Unlimited Transponder Security Key. This allows all the customer vehicles to share the same keys, but no other keys from outside can be used to operate the vehicles. For an individual customer, any randomly selected Security Key is acceptable. Refer to Unlimited Key Mode Programming in Key Programming Switch State Control in this section.
The PATS transceiver module communicates with the encoded ignition key. The module is located behind the steering column shroud and contains an antenna connected to a small electronics module. During each vehicle start sequence, the transceiver module reads the encoded ignition key identification code and sends data to the PCM.
The control functions are contained in the PCM. This module carries out all of the PATS functions, such as receiving the identification code from the encoded ignition key and controlling the engine enable. The PCM initiates the key interrogation sequence when the vehicle ignition switch is turned to RUN or START.
All elements of the PATS must be functional before the engine is allowed to start. If any of the components are not working correctly, the vehicle will not start.
The PATS uses a visual theft indicator. The indicator will prove out for three seconds when the ignition switch is turned to RUN or START under normal operation. If there is a PATS concern, this indicator will either flash rapidly or glow steadily when the ignition switch is turned to RUN or START. The PATS system also flashes the theft indicator every two seconds at ignition OFF to act as a visual deterrent.
The following will activate the PATS and will disable the vehicle from starting:
  • incorrectly encoded ignition key
  • damaged encoded ignition key
  • unprogrammed key
  • non-encoded key (key has no electronics)
  • damaged wiring
  • damaged transceiver
  • damaged PCM

May 26, 2009 | 2003 Ford Windstar

2 Answers

My 2000 Ford Taurus will not start because of the security system


the security system resets itself after about 15 minutes. If it was the security system, the car would not crank over. Why do you think it's the security system?
do you have gas in tank?

Is it a Ford security system, with the flashing light on the dash?


Principles of Operation
The PATS uses a specially encoded ignition key, this key is not compatible with previous vehicles or any current model year vehicles. Each specially encoded ignition key contains a permanently installed electronic device called a transponder. Each transponder contains a unique encrypted identification code out of over 18 billion, billion combinations.
Each encoded ignition key must be programmed into the vehicle's powertrain control module (PCM) before it can be used to start the engine. There are special diagnostic repair procedures outlined in this manual that must be carried out if a new encoded ignition key is necessary.
This system contains a new feature named Unlimited Key Mode. This feature allows a customer to program more than eight keys to their vehicle if they request it. Each vehicle in Unlimited Key Mode is set up with a special Unlimited Transponder Security Key. This allows all the customer vehicles to share the same keys, but no other keys from outside can be used to operate the vehicles. For an individual customer, any randomly selected Security Key is acceptable. Refer to Key Programming—Unlimited Key Mode in this section.
The PATS transceiver module communicates with the encoded ignition key. The module is located behind the steering wheel column shroud and contains an antenna connected to a small electronics module. During each vehicle start sequence, the transceiver module reads the encoded ignition key identification code and sends data to the PCM.
The control functions are contained in the PCM. This module carries out all of the PATS functions, such as receiving the identification code from the encoded ignition key and controlling the engine enable. The PCM initiates the key interrogation sequence when the vehicle ignition switch is turned to RUN or START.
All elements of the PATS must be functional before the engine is allowed to start. If any of the components are not working correctly, the vehicle will not start.
The PATS uses a visual theft indicator. The indicator will prove out for three seconds when the ignition switch is turned to RUN or START under normal operation. If there is a PATS problem, this indicator will either flash rapidly or glow steadily when the ignition switch is turned to RUN or START. The PATS system also flashes the theft indicator every two seconds at ignition OFF to act as a visual deterrent.
The PATS will be activated and will disable the vehicle from starting if there is a:
  • improper encoded ignition key (example — Taurus/Sable key).
  • damaged encoded ignition key.
  • unprogrammed key.
  • non-encoded key (key has no electronics).
  • damaged wiring.
  • damaged transceiver.

Apr 13, 2009 | 2000 Ford Taurus

3 Answers

2004 Ford Explorer won't start. Think we need to


it resets itself.

Principles of Operation
The PATS uses a specially encoded ignition key. Each encoded ignition key contains a permanently installed electronic device called a transponder. Each transponder contains a unique electronic identification code out of over 18 billion, billion combinations.
The passive anti-theft system (PATS), also known as SecuriLock ®, uses radio frequency identification technology to deter a drive-away theft. This system is known as SecuriLock® in North America, Safeguard® in the U.K., and PATS in Continental Europe. Passive means that it does not require any activity from the user.
The SecuriLock® System (PATS) is not compatible with aftermarket remote start systems, which allow the vehicle to be started from outside the vehicle. These systems may reduce the vehicle security level, and also may cause no-start issues. If equipped the remote start system must be removed before investigation of PATS-related, no-start issues.
Each encoded ignition key must be programmed into the vehicle's powertrain control (PCM) before it can be used to start the engine. There are special diagnostic repair procedures described in this section that must be carried out if a new encoded ignition key is necessary.
This system contains a new feature named Unlimited Key Mode. This feature allows a customer to program more than eight keys to the vehicle if they request it. Each vehicle in Unlimited Key Mode is set up with a special Unlimited Transponder Security Key. This allows all the customer vehicles to share the same keys, but no other keys from outside can be used to operate the vehicles. For an individual customer, any randomly selected Security Key is acceptable. Refer to Unlimited Key Mode Programming in Key Programming Switch State Control in this section.
The PATS transceiver module communicates with the encoded ignition key. The module is located behind the steering column shroud and contains an antenna connected to a small electronics module. During each vehicle start sequence, the transceiver module reads the encoded ignition key identification code and sends data to the PCM.
The control functions are contained in the PCM. This module carries out all of the PATS functions, such as receiving the identification code from the encoded ignition key and controlling the engine enable. The PCM initiates the key interrogation sequence when the vehicle ignition switch is turned to RUN or START.
All elements of the PATS must be functional before the engine is allowed to start. If any of the components are not working correctly, the vehicle will not start.
The PATS uses a visual theft indicator. The indicator will prove out for three seconds when the ignition switch is turned to RUN or START under normal operation. If there is a PATS concern, this indicator will either flash rapidly or glow steadily when the ignition switch is turned to RUN or START. The PATS system also flashes the theft indicator every two seconds at ignition OFF to act as a visual deterrent.
The PATS will be activated and will disable the vehicle from starting if there is a:
  • incorrectly encoded ignition key
  • damaged encoded ignition key
  • unprogrammed key
  • non-encoded key (key has no electronics)
  • damaged wiring
  • damaged transceiver
  • damaged PCM

Feb 22, 2009 | 1999 Mercury Cougar

2 Answers

Antitheft and battery lite on 2006 ford freestar


Try your spare key first. also, does the anti theft visual indicator (red flashing light) prove out, that is light for three seconds when key is turned to on.

here's some info.

Principles of Operation
The passive anti-theft system (PATS) uses a specially encoded ignition key. Each encoded ignition key contains a permanently installed electronic device called a transponder. Each transponder contains a unique electronic identification code out of over 18 billion, billion combinations.
The passive anti-theft system (PATS), also known as SecuriLock ®, uses radio frequency identification technology to deter a drive-away theft. This system is known as SecuriLock® in North America, Safeguard® in the U.K., and PATS in continental Europe. Passive means that it does not require any activity from the user.
The SecuriLock® System (PATS) is not compatible with NON-FORD remote start systems, which allow the vehicle to be started from outside the vehicle. These systems may reduce the vehicle security level, and also may cause no-start issues. If equipped, the remote start system must be removed before investigation of PATS-related, no-start issues.
Each encoded ignition key must be programmed into the vehicle's powertrain control module (PCM) before it can be used to start the engine. The correct ignition key is a different design than prior model years. Consult the Rotunda Key Ordering Guide for the correct part number. There are special diagnostic repair procedures described in this section that must be carried out if a new encoded ignition key is necessary.
This system contains a new feature named Unlimited Key Mode. This feature allows a customer to program more than eight keys to the vehicle if they request it. Each vehicle in Unlimited Key Mode is set up with a special unlimited transponder security key. This allows all the customer vehicles to share the same keys, but no other keys from outside can be used to operate the vehicles. For an individual customer, any randomly selected security key is acceptable. Refer to Unlimited Key Mode Programming in Key Programming Switch State Control in this section.
The PATS transceiver module communicates with the encoded ignition key. The module is located behind the steering column shroud and contains an antenna connected to a small electronics module. During each vehicle start sequence, the transceiver module reads the encoded ignition key identification code and sends data to the PCM.
The control functions are contained in the PCM. This module carries out all of the PATS functions, such as receiving the identification code from the encoded ignition key and controlling the engine enable. The PCM initiates the key interrogation sequence when the vehicle ignition switch is turned to RUN or START.
All elements of the PATS must be functional before the engine is allowed to start. If any of the components are not working correctly, the vehicle will not start.
PATS uses a visual theft indicator. The indicator will prove out for three seconds when the ignition switch is turned to RUN or START under normal operation. If there is a PATS concern, this indicator will either flash rapidly or glow steadily when the ignition switch is turned to RUN or START. The PATS system also flashes the theft indicator every two seconds at ignition OFF to act as a visual deterrent.
PATS will be activated and will disable the vehicle from starting if there is:
  • an incorrectly encoded ignition key.
  • a damaged encoded ignition key.
  • an unprogrammed key
  • a non-encoded key (key has no electronics).
  • damaged wiring.
  • a damaged transceiver.
  • a damaged PCM.

Jan 09, 2009 | 2004 Ford Taurus

Not finding what you are looking for?
2003 Ford Escort Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...