Question about Cars & Trucks

1 Answer

Hazard and turn signal do not work

I just purchased this car and the hazards and turn signal do not operate. Does the flasher under the dash control both.

Posted by on

  • Sylvia Vasquez Nov 07, 2012

    its a 1995 ford thunderbird lx

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 75,005 Answers

You most likely need to replace the combination flasher relay a very common problem.
.
The Electronic Flasher is located behind behind and under LH side of the instrument panel, left of steering column

Posted on Nov 07, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

goalie39
  • 469 Answers

SOURCE: turn signals and hazard don't work

Next best guess is the flasher unit has failed, this could be your little blue box, pick up a replacement at any auto parts store and replace it.

Posted on Apr 15, 2009

  • 272 Answers

SOURCE: 1997 sonoma turn signal flasher

The flashers are located behind the instrument panel trim, roughly between the base of the steering wheel and the ashtray, just to the left of the car lighter. To access the flashers, you need to at least loosen the lower instrument panel trim. Just under the steering column there are two screws with star heads. One to the left of the column and one to the right. You need to remove both of these screws. You will need to remove your ashtray. On the upper left corner of the hole left by removing the ashtray is a 9/32 hex head screw. You need to remove it. Once these three screws are removed you should be able to pull down on this portion of trim under your instrument cluster. When you do this it may cause trim around your instrument cluster to loosen that you can just pop back into place with your hand. You won't need to pull down to far on this trim piece as there are still some screws holding the bottom. You should be able to pull it down far enough to see the flasher units behind and just to the left of the cigarette lighter. There are two flasher units and I found that the one on the right is for the turn signals.On the left the other is for the hazard flashers. It may be a hand scraping experience to replace the flasher but it beats paying someone to do it for you. They are easy to recognize because the are silver and round metallic plug ins. The flasher unit on the left is for the emergency flashers and the one on the right is for turn signals. You can place the emergency flasher unit into the slot the turn signal unit belongs until you get a replacement. These flasher units are pretty cheap.

Posted on Jun 02, 2009

  • 4369 Answers

SOURCE: where is the turn signal\hazard flasher located?

it's in the auxiliary relay box behind the glove box.

13350 is base part number on flasher

Posted on Feb 03, 2010

Testimonial: "Actually found it located behind the radio mounted on a brace. Removed cover and relay pulls out. About 1" cube with 5 terminals on it."

  • 1 Answer

SOURCE: 1999 Camry Turn signals and hazard lights not working.

located on the firewall panel on the left side of the floorboard on the drivers side

Posted on Mar 27, 2010

  • 1 Answer

SOURCE: turn signals hazards flasher don't work jeep

I NEED TO LOCATE THE SWITCH WHERE IS IT ?
MY INDICATORS NOR HAZARD LIGHTS ARE WORKING I DONT KNOW WHAT IS WRONG WITH IT CHANGED BULBS BUT NOTHIGN THEY ALL WENT OUT AT THE SAME TIME
SO THERE MUST BE A RELAY SWITCH SOMEWHER BUT DONT KNOW WHERE ?
THANKS FOR HELPING

Posted on Apr 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

LOCATION OF TURN SIGNAL FLASHER 2001 BONNEVILLE


It's part of the hazard switch , electronic module !
Turn Signal/Hazard Flasher Module
In the center of the IP part of the hazard flasher switch

2001 pontiac bonneville flasher module-0gh0golvpqxksfrzlnez2sc5-2-0.jpg

Jun 06, 2017 | Cars & Trucks

1 Answer

1985 LeSabre flashers work turn signals don't need location of turn signal switch or are they one of the same


You mean turn signal flasher? No, the hazard flasher and turn flasher on older cars were separate. Often, the hazard flasher was right of the steering column (under the dash), and the turn flasher was left of the column. Look for two similar canisters. Turn the hazard lights on and locate the hazard flasher by feel or hearing. The turn flasher will be the other one. They both may be retained by metal clips.

Sep 16, 2015 | Cars & Trucks

2 Answers

Where is the emergency flasher relay located on 2013 Rogue?


Here is what the service manual says. Looks like it is not a flasher relay but a function of the body control module.

TURN SIGNAL AND HAZARD WARNING LAMP SYSTEMSystem Description OUTLINE Turn signal lamp and the hazard warning lamp is controlled by combination switch reading function and the flasher control function of BCM.
TURN SIGNAL LAMP OPERATION - BCM detects the combination switch condition by the combination switch reading function. - BCM supplies voltage to the right (left) turn signal lamp circuit when the ignition switch is turned ON and the turn signal switch is in the right (left) position. BCM blinks the turn signal lamp.
HAZARD WARNING LAMP OPERATION BCM supplies voltage to both turn signal lamp circuit when the hazard switch is turned ON. BCM blinks the hazard warning lamp.
TURN SIGNAL INDICATOR LAMP AND TURN SIGNAL SOUND OPERATION - BCM transmits the turn indicator signal to the combination meter with CAN communication while the turn signal lamp and the hazard warning lamp are operating. - Combination meter outputs the turn signal sound with the integrated buzzer while blinking the turn signal indicator lamp according to the turn indicator signal.
HIGH FLASHER OPERATION (FAIL-SAFE) - BCM detects the turn signal lamp circuit status by the terminal current value. - BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal lamp operating. NOTE: The blinking speed is normal while operating the hazard warning lamp.

Oct 13, 2014 | 2013 Nissan Rogue

1 Answer

I have a 1987 chevy deluxe r10 dont have any turn signal I have head light brake lights park light an hazard lights but no right turn signal nor left turn signal I have check all fuses and put a new signal...


I think you might have a separate flasher for the turn signals under the dash. The turn and hazard flasher would look alike. Turn you hazards on and find the flasher for it under the dash. You will probably be able to feel it working and hear it clicking. The other flasher under the dash is for the turn signals. Try replacing that one. I think it was in later years they began to combine the two into a single composite flasher.

Mar 01, 2013 | Chevrolet Cars & Trucks

1 Answer

Can,t get signal or flashers to work on 1997 Dodge Intrepid


I assume you've checked the Fuses :p Obviously that hasnt worked and the bulbs and lights haven't worked either... SO try this????
Open the driver's side door and examine the end of the dash for an access panel. Behind the access panel are fuses and flashers. There are two flashers inside the access panel for controlling the turn signal and the hazard lights. You can distinguish them apart from each other by turning on the hazards or the turn signal and feeling for the clicking. If you turned on the hazards, then the flasher that is clicking is the hazard flasher.
Remove the turn signal flasher from the dash and reinstall the new flasher into the vacated slot in the dash. Close the access panel and start thetruck . Check the turn signals for proper operation and make sure the hazards work as well.


Please let me know how it goes
  • Jan 07, 2012 | Cars & Trucks

    1 Answer

    No turn signals or hazards???


    Check the FLASHER unit; the turn signal flasher is mounted in a clip on the right side of the steering column support bracket. The hazard flasher is located in the component center, under the instrument panel, on the right side. Replace the flasher by unplugging the old one and plugging in the new one.

    Hazard flasher -->> The Flasher is located: Front seating area, passenger side, under dash, below glove compartment, mounted in fuse panel

    Turn signal -->> The Flasher is located: Front seating area, driver side, under dash, mounted on passenger side of steering column

    Good luck (remember comment and rated this).

    Apr 23, 2010 | 1995 Chevrolet Monte Carlo

    3 Answers

    Turn signals wont work fuses are good?


    the hazard switch above the radio is your problem. if you put on your signals and they don't flash turn hazards on then off and they will flash. (changing this *** will fix your problem

    Aug 30, 2009 | 1999 Pontiac Grand Am GT

    4 Answers

    Flasher location


    I believe the hazard/flasher relay is located under/left of the dash . I think if you remove the under panel under the steering column it should be attached to the BCM bracket under the dash on the left side.

    Remove the left instrument panel (IP) insulator.
    Remove the steering column filler panel.
    Slide the hazard and turn signal flasher to the right, releasing the tabs from the Body Control Module (BCM) bracket.
    Disconnect the electrical connector from the hazard and turn signal flasher.

    Hope this helps.....

    Apr 29, 2009 | 2003 Pontiac Grand Prix

    1 Answer

    Turn signals are not working


    check for faulty signal light flasher located under L/S dash. Separate flasher for hazard lights and signal lights.

    Mar 30, 2009 | 1994 Buick Park Avenue

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    41 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    75005 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...